[U-Boot] [PATCH v2 08/14] arm/km: redefine piggy 4 reg names to avoid conflicts
Holger Brunck
holger.brunck at keymile.com
Wed Jun 13 15:33:14 CEST 2012
From: Valentin Longchamp <valentin.longchamp at keymile.com>
Some very similar #defines for reg addresses are used in a later patch
(managed_switch support for km_arm).
Signed-off-by: Valentin Longchamp <valentin.longchamp at keymile.com>
cc: Holger Brunck <holger.brunck at keymile.com>
cc: Prafulla Wadaskar <prafulla at marvell.com>
---
changes for v2:
- nothing
board/keymile/km_arm/km_arm.c | 22 +++++++++++-----------
1 files changed, 11 insertions(+), 11 deletions(-)
diff --git a/board/keymile/km_arm/km_arm.c b/board/keymile/km_arm/km_arm.c
index 5c9ba8f..d9cd4a0 100644
--- a/board/keymile/km_arm/km_arm.c
+++ b/board/keymile/km_arm/km_arm.c
@@ -332,13 +332,13 @@ void dram_init_banksize(void)
#if (defined(CONFIG_KM_PIGGY4_88E6061))
-#define PHY_LED_SEL 0x18
-#define PHY_LED0_LINK (0x5)
-#define PHY_LED1_ACT (0x8<<4)
-#define PHY_LED2_INT (0xe<<8)
-#define PHY_SPEC_CTRL 0x1c
+#define PHY_LED_SEL_REG 0x18
+#define PHY_LED0_LINK (0x5)
+#define PHY_LED1_ACT (0x8<<4)
+#define PHY_LED2_INT (0xe<<8)
+#define PHY_SPEC_CTRL_REG 0x1c
#define PHY_RGMII_CLK_STABLE (0x1<<10)
-#define PHY_CLSA (0x1<<1)
+#define PHY_CLSA (0x1<<1)
/* Configure and enable MV88E3018 PHY */
void reset_phy(void)
@@ -350,15 +350,15 @@ void reset_phy(void)
return;
/* RGMII clk transition on data stable */
- if (miiphy_read(name, CONFIG_PHY_BASE_ADR, PHY_SPEC_CTRL, ®) != 0)
+ if (!miiphy_read(name, CONFIG_PHY_BASE_ADR, PHY_SPEC_CTRL_REG, ®))
printf("Error reading PHY spec ctrl reg\n");
- if (miiphy_write(name, CONFIG_PHY_BASE_ADR, PHY_SPEC_CTRL,
- reg | PHY_RGMII_CLK_STABLE | PHY_CLSA) != 0)
+ if (!miiphy_write(name, CONFIG_PHY_BASE_ADR, PHY_SPEC_CTRL_REG,
+ reg | PHY_RGMII_CLK_STABLE | PHY_CLSA))
printf("Error writing PHY spec ctrl reg\n");
/* leds setup */
- if (miiphy_write(name, CONFIG_PHY_BASE_ADR, PHY_LED_SEL,
- PHY_LED0_LINK | PHY_LED1_ACT | PHY_LED2_INT) != 0)
+ if (!miiphy_write(name, CONFIG_PHY_BASE_ADR, PHY_LED_SEL_REG,
+ PHY_LED0_LINK | PHY_LED1_ACT | PHY_LED2_INT))
printf("Error writing PHY LED reg\n");
/* reset the phy */
--
1.7.1
More information about the U-Boot
mailing list