[U-Boot] [PATCH v5 06/13] mkconfig: add support for SPL CPU
Allen Martin
amartin at nvidia.com
Tue Jun 26 00:55:28 CEST 2012
Add support for specifying a different CPU for main u-boot and SPL
u-boot builds. This is done by adding an optional SPL CPU after the
main CPU in boards.cfg as follows:
normal_cpu:spl_cpu
This this case CPU will be set to "normal_cpu" during the main u-boot
build and "spl_cpu" during the SPL build.
Signed-off-by: Allen Martin <amartin at nvidia.com>
Acked-by: Stephen Warren <swarren at wwwdotorg.org>
---
boards.cfg | 5 +++++
doc/README.SPL | 12 ++++++++++++
mkconfig | 24 ++++++++++++++++--------
3 files changed, 33 insertions(+), 8 deletions(-)
diff --git a/boards.cfg b/boards.cfg
index f7f1190..8958ba2 100644
--- a/boards.cfg
+++ b/boards.cfg
@@ -11,6 +11,11 @@
# Lines starting with '#' are comments.
# Blank lines are ignored.
#
+# The CPU field takes the form:
+# cpu[:spl_cpu]
+# If spl_cpu is specified the make variable CPU will be set to this
+# during the SPL build.
+#
# The options field takes the form:
# <board config name>[:comma separated config options]
# Each config option has the form (value defaults to "1"):
diff --git a/doc/README.SPL b/doc/README.SPL
index 0276953..e4a5ac3 100644
--- a/doc/README.SPL
+++ b/doc/README.SPL
@@ -66,3 +66,15 @@ CONFIG_SPL_DMA_SUPPORT (drivers/dma/libdma.o)
CONFIG_SPL_POST_MEM_SUPPORT (post/drivers/memory.o)
CONFIG_SPL_NAND_LOAD (drivers/mtd/nand/nand_spl_load.o)
CONFIG_SPL_SPI_LOAD (drivers/mtd/spi/spi_spl_load.o)
+
+
+Normally CPU is assumed to be the same between the SPL and normal
+u-boot build. However it is possible to specify a different CPU for
+the SPL build for cases where the SPL is expected to run on a
+different CPU model from the main u-boot. This is done by specifying
+an SPL CPU in boards.cfg as follows:
+
+ normal_cpu:spl_cpu
+
+This this case CPU will be set to "normal_cpu" during the main u-boot
+build and "spl_cpu" during the SPL build.
diff --git a/mkconfig b/mkconfig
index 3e9c695..cc77a56 100755
--- a/mkconfig
+++ b/mkconfig
@@ -59,7 +59,8 @@ CONFIG_NAME="${1%_config}"
[ "${BOARD_NAME}" ] || BOARD_NAME="${1%_config}"
arch="$2"
-cpu="$3"
+cpu=`echo $3 | awk 'BEGIN {FS = ":"} ; {print $1}'`
+spl_cpu=`echo $3 | awk 'BEGIN {FS = ":"} ; {print $2}'`
if [ "$4" = "-" ] ; then
board=${BOARD_NAME}
else
@@ -130,13 +131,20 @@ fi
#
# Create include file for Make
#
-echo "ARCH = ${arch}" > config.mk
-echo "CPU = ${cpu}" >> config.mk
-echo "BOARD = ${board}" >> config.mk
-
-[ "${vendor}" ] && echo "VENDOR = ${vendor}" >> config.mk
-
-[ "${soc}" ] && echo "SOC = ${soc}" >> config.mk
+( echo "ARCH = ${arch}"
+ if [ ! -z "$spl_cpu" ] ; then
+ echo 'ifeq ($(CONFIG_SPL_BUILD),y)'
+ echo "CPU = ${spl_cpu}"
+ echo "else"
+ echo "CPU = ${cpu}"
+ echo "endif"
+ else
+ echo "CPU = ${cpu}"
+ fi
+ echo "BOARD = ${board}"
+
+ [ "${vendor}" ] && echo "VENDOR = ${vendor}"
+ [ "${soc}" ] && echo "SOC = ${soc}" ) > config.mk
# Assign board directory to BOARDIR variable
if [ -z "${vendor}" ] ; then
--
1.7.9.5
More information about the U-Boot
mailing list