[U-Boot] [PATCH 15/21] arm/km: add kmnusa board support
Holger Brunck
holger.brunck at keymile.com
Wed Mar 21 16:49:34 CET 2012
This board is similar to portl2, but it has the u-boot environment
in a SPI NOR flash and not in an i2c eeprom like portl2 have.
Some other details:
- IVM EEPROM is at adress: pca9547:70:9
- PCI is enabled
- PIGGY4 is connected via MV88E6352 simple switch. There is no phy
between the simple switch and the kirkwood.
Signed-off-by: Holger Brunck <holger.brunck at keymile.com>
Signed-off-by: Valentin Longchamp <valentin.longchamp at keymile.com>
cc: Gerlando Falauto <gerlando.falauto at keymile.com>
cc: Prafulla Wadaskar <prafulla at marvell.com>
---
MAINTAINERS | 1 +
board/keymile/km_arm/128M16-1.cfg | 290 +++++++++++++++++++++++++++++++++++++
board/keymile/km_arm/km_arm.c | 9 +-
boards.cfg | 1 +
include/configs/km/km_arm.h | 44 +++++-
include/configs/km_kirkwood.h | 67 +++++++--
6 files changed, 388 insertions(+), 24 deletions(-)
create mode 100644 board/keymile/km_arm/128M16-1.cfg
diff --git a/MAINTAINERS b/MAINTAINERS
index 652113f..ddf9613 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -743,6 +743,7 @@ Sergey Lapin <slapin at ossfans.org>
Valentin Longchamp <valentin.longchamp at keymile.com>
km_kirkwood ARM926EJS (Kirkwood SoC)
+ kmnusa ARM926EJS (Kirkwood SoC)
mgcoge3un ARM926EJS (Kirkwood SoC)
portl2 ARM926EJS (Kirkwood SoC)
diff --git a/board/keymile/km_arm/128M16-1.cfg b/board/keymile/km_arm/128M16-1.cfg
new file mode 100644
index 0000000..cef8ea6
--- /dev/null
+++ b/board/keymile/km_arm/128M16-1.cfg
@@ -0,0 +1,290 @@
+#
+# (C) Copyright 2010
+# Heiko Schocher, DENX Software Engineering, hs at denx.de.
+#
+# (C) Copyright 2012
+# Valentin Longchamp, Keymile AG, valentin.longchamp at keymile.com
+# Stefan Bigler, Keymile AG, stefan.bigler at keymile.com
+#
+# (C) Copyright 2012
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
+# MA 02110-1301 USA
+#
+# Refer docs/README.kwimage for more details about how-to configure
+# and create kirkwood boot image
+#
+
+# Boot Media configurations
+BOOT_FROM spi # Boot from SPI flash
+
+DATA 0xFFD10000 0x01112222 # MPP Control 0 Register
+# bit 3-0: 2, MPPSel0 SPI_CSn (1=NF_IO[2])
+# bit 7-4: 2, MPPSel1 SPI_SI (1=NF_IO[3])
+# bit 12-8: 2, MPPSel2 SPI_SCK (1=NF_IO[4])
+# bit 15-12: 2, MPPSel3 SPI_SO (1=NF_IO[5])
+# bit 19-16: 1, MPPSel4 NF_IO[6]
+# bit 23-20: 1, MPPSel5 NF_IO[7]
+# bit 27-24: 1, MPPSel6 SYSRST_O
+# bit 31-28: 0, MPPSel7 GPO[7]
+
+DATA 0xFFD10004 0x03303300 # MPP Control 1 Register
+# bit 3-0: 0, MPPSel8 GPIO[8]
+# bit 7-4: 0, MPPSel9 GPIO[9]
+# bit 12-8: 3, MPPSel10 UA0_TXD
+# bit 15-12: 3, MPPSel11 UA0_RXD
+# bit 19-16: 0, MPPSel12 not connected
+# bit 23-20: 3, MPPSel13 UA1_TXD
+# bit 27-24: 3, MPPSel14 UA1_RXD
+# bit 31-28: 0, MPPSel15 GPIO[15]
+
+DATA 0xFFD10008 0x00001100 # MPP Control 2 Register
+# bit 3-0: 0, MPPSel16 GPIO[16]
+# bit 7-4: 0, MPPSel17 not connected
+# bit 12-8: 1, MPPSel18 NF_IO[0]
+# bit 15-12: 1, MPPSel19 NF_IO[1]
+# bit 19-16: 0, MPPSel20 GPIO[20]
+# bit 23-20: 0, MPPSel21 GPIO[21]
+# bit 27-24: 0, MPPSel22 GPIO[22]
+# bit 31-28: 0, MPPSel23 GPIO[23]
+
+# MPP Control 3-6 Register untouched (MPP24-49)
+
+DATA 0xFFD100E0 0x1B1B1B1B # IO Configuration 0 Register
+# bit 2-0: 3, Reserved
+# bit 5-3: 3, Reserved
+# bit 6: 0, Reserved
+# bit 7: 0, RGMII-pads voltage = 3.3V
+# bit 10-8: 3, Reserved
+# bit 13-11: 3, Reserved
+# bit 14: 0, Reserved
+# bit 15: 0, MPP RGMII-pads voltage = 3.3V
+# bit 31-16 0x1B1B, Reserved
+
+DATA 0xFFD20134 0x66666666 # L2 RAM Timing 0 Register
+# bit 0-1: 2, Tag RAM RTC RAM0
+# bit 3-2: 1, Tag RAM WTC RAM0
+# bit 7-4: 6, Reserve
+# bit 9-8: 2, Valid RAM RTC RAM
+# bit 11-10: 1, Valid RAM WTC RAM
+# bit 13-12: 2, Dirty RAM RTC RAM
+# bit 15-14: 1, Dirty RAM WTC RAM
+# bit 17-16: 2, Data RAM RTC RAM0
+# bit 19-18: 1, Data RAM WTC RAM0
+# bit 21-20: 2, Data RAM RTC RAM1
+# bit 23-22: 1, Data RAM WTC RAM1
+# bit 25-24: 2, Data RAM RTC RAM2
+# bit 27-26: 1, Data RAM WTC RAM2
+# bit 29-28: 2, Data RAM RTC RAM3
+# bit 31-30: 1, Data RAM WTC RAM4
+
+DATA 0xFFD20138 0x66666666 # L2 RAM Timing 1 Register
+# bit 15-0: ???, Reserve
+# bit 17-16: 2, ECC RAM RTC RAM0
+# bit 19-18: 1, ECC RAM WTC RAM0
+# bit 31-20: ???,Reserve
+
+DATA 0xFFD20154 0x00000200 # CPU RAM Management Control3 Register
+# bit 23-0: 0x000200, Addr Config tuning
+# bit 31-24: 0, Reserved
+
+# ??? Missing register # CPU RAM Management Control2 Register
+
+DATA 0xFFD2014C 0x00001C00 # CPU RAM Management Control1 Register
+# bit 15-0: 0x1C00, Opmux Tuning
+# bit 31-16: 0, Pc Dp Tuning
+
+DATA 0xFFD20148 0x00000001 # CPU RAM Management Control0 Register
+# bit 1-0: 1, addr clk tune
+# bit 3-2: 0, reserved
+# bit 5-4: 0, dtcmp clk tune
+# bit 7-6: 0, reserved
+# bit 9-8: 0, macdrv clk tune
+# bit 11-10: 0, opmuxgm2 clk tune
+# bit 15-14: 0, rf clk tune
+# bit 17-16: 0, rfbypass clk tune
+# bit 19-18: 0, pc dp clk tune
+# bit 23-20: 0, icache clk tune
+# bit 27:24: 0, dcache clk tune
+# bit 31:28: 0, regfile tunin
+
+# SDRAM initalization
+DATA 0xFFD01400 0x430004E0 # SDRAM Configuration Register
+# bit 13-0: 0x4E0, DDR2 clks refresh rate
+# bit 14: 0, reserved
+# bit 15: 0, reserved
+# bit 16: 0, CPU to Dram Write buffer policy
+# bit 17: 0, Enable Registered DIMM or Equivalent Sampling Logic
+# bit 19-18: 0, reserved
+# bit 23-20: 0, reserved
+# bit 24: 1, enable exit self refresh mode on DDR access
+# bit 25: 1, required
+# bit 29-26: 0, reserved
+# bit 31-30: 1, reserved
+
+DATA 0xFFD01404 0x36543000 # DDR Controller Control Low
+# bit 3-0: 0, reserved
+# bit 4: 0, 2T mode =addr/cmd in same cycle
+# bit 5: 0, clk is driven during self refresh, we don't care for APX
+# bit 6: 0, use recommended falling edge of clk for addr/cmd
+# bit 7-11: 0, reserved
+# bit 12-13: 1, reserved, required 1
+# bit 14: 0, input buffer always powered up
+# bit 17-15: 0, reserved
+# bit 18: 1, cpu lock transaction enabled
+# bit 19: 0, reserved
+# bit 23-20: 5, recommended value for CL=4 and STARTBURST_DEL disabled bit31=0
+# bit 27-24: 6, CL+1, STARTBURST sample stages, for freqs 200-399MHz, unbuffered DIMM
+# bit 30-28: 3, required
+# bit 31: 0,no additional STARTBURST delay
+
+DATA 0xFFD01408 0x2302444e # DDR Timing (Low) (active cycles value +1)
+# bit 3-0: 0xE, TRAS, 15 clk (45 ns)
+# bit 7-4: 0x4, TRCD, 5 clk (15 ns)
+# bit 11-8: 0x4, TRP, 5 clk (15 ns)
+# bit 15-12: 0x4, TWR, 5 clk (15 ns)
+# bit 19-16: 0x2, TWTR, 3 clk (7.5 ns)
+# bit 20: 0, extended TRAS msb
+# bit 23-21: 0, reserved
+# bit 27-24: 0x3, TRRD, 4 clk (10 ns)
+# bit 31-28: 0x2, TRTP, 3 clk (7.5 ns)
+
+DATA 0xFFD0140C 0x0000003e # DDR Timing (High)
+# bit 6-0: 0x3E, TRFC, 63 clk (195 ns)
+# bit 8-7: 0, TR2R
+# bit 10-9: 0, TR2W
+# bit 12-11: 0, TW2W
+# bit 31-13: 0, reserved
+
+DATA 0xFFD01410 0x00000001 # DDR Address Control
+# bit 1-0: 1, Cs0width=x16
+# bit 3-2: 0, Cs0size=2Gb
+# bit 5-4: 0, Cs1width=nonexistent
+# bit 7-6: 0, Cs1size =nonexistent
+# bit 9-8: 0, Cs2width=nonexistent
+# bit 11-10: 0, Cs2size =nonexistent
+# bit 13-12: 0, Cs3width=nonexistent
+# bit 15-14: 0, Cs3size =nonexistent
+# bit 16: 0, Cs0AddrSel
+# bit 17: 0, Cs1AddrSel
+# bit 18: 0, Cs2AddrSel
+# bit 19: 0, Cs3AddrSel
+# bit 31-20: 0, required
+
+DATA 0xFFD01414 0x00000000 # DDR Open Pages Control
+# bit 0: 0, OpenPage enabled
+# bit 31-1: 0, required
+
+DATA 0xFFD01418 0x00000000 # DDR Operation
+# bit 3-0: 0, DDR cmd
+# bit 31-4: 0, required
+
+DATA 0xFFD0141C 0x00000652 # DDR Mode
+# bit 2-0: 2, Burst Length = 4
+# bit 3: 0, Burst Type
+# bit 6-4: 5, CAS Latency = 5
+# bit 7: 0, Test mode
+# bit 8: 0, DLL Reset
+# bit 11-9: 3, Write recovery for auto-precharge must be 3
+# bit 12: 0, Active power down exit time, fast exit
+# bit 14-13: 0, reserved
+# bit 31-15: 0, reserved
+
+DATA 0xFFD01420 0x00000006 # DDR Extended Mode
+# bit 0: 0, DDR DLL enabled
+# bit 1: 1, DDR drive strength reduced
+# bit 2: 1, DDR ODT control lsb, 75 ohm termination [RTT0]
+# bit 5-3: 0, required
+# bit 6: 0, DDR ODT control msb, 75 ohm termination [RTT1]
+# bit 9-7: 0, required
+# bit 10: 0, differential DQS enabled
+# bit 11: 0, required
+# bit 12: 0, DDR output buffer enabled
+# bit 31-13: 0 required
+
+DATA 0xFFD01424 0x0000F17F # DDR Controller Control High
+# bit 2-0: 7, required
+# bit 3: 1, MBUS Burst Chop disabled
+# bit 6-4: 7, required
+# bit 7: 0, reserved
+# bit 8: 1, add sample stage required for f > 266 MHz
+# bit 9: 0, no half clock cycle addition to dataout
+# bit 10: 0, 1/4 clock cycle skew enabled for addr/ctl signals
+# bit 11: 0, 1/4 clock cycle skew disabled for write mesh
+# bit 15-12:0xf, required
+# bit 31-16: 0, required
+
+DATA 0xFFD01428 0x00074510 # DDR2 SDRAM Timing Low
+# bit 3-0: 0, required
+# bit 7-4: 1, M_ODT assertion 1 cycle after read
+# bit 11-8: 5, M_ODT de-assertion 5 cycles after read
+# (ODT turn off delay 2,5 clk cycles)
+# bit 15-12: 4, internal ODT assertion
+# bit 19-16: 7, internal ODT de-assertion
+# bit 31-20: 0, required
+
+DATA 0xFFD0147c 0x00007451 # DDR2 SDRAM Timing High
+# bit 3-0: 1, M_ODT assertion
+# bit 7-4: 5, M_ODT de-assertion
+# bit 11-8: 4, internal ODT assertion 1 cycles after write
+# bit 15-12: 7, internal ODT de-assertion 7 cycles after write
+
+DATA 0xFFD01500 0x00000000 # CS[0]n Base address to 0x0
+# bit 23-0: 0, reserved
+# bit 31-24: 0, CPU CS Window0 Base Address, addr bits [31:24]
+
+DATA 0xFFD01504 0x0FFFFFF1 # CS[0]n Size
+# bit 0: 1, Window enabled
+# bit 1: 0, Write Protect disabled
+# bit 3-2: 0, CS0 hit selected
+# bit 23-4:ones, required
+# bit 31-24: 0x0F, Size (i.e. 256MB)
+
+DATA 0xFFD0150C 0x00000000 # CS[1]n Size, window disabled
+DATA 0xFFD01514 0x00000000 # CS[2]n Size, window disabled
+DATA 0xFFD0151C 0x00000000 # CS[3]n Size, window disabled
+
+DATA 0xFFD01494 0x00010000 # DDR ODT Control (Low)
+# bit 3-0: 0, ODT0Rd, MODT[0] not asserted during read from DRAM CS0
+# bit 7-4: 0, ODT0Rd, MODT[1] not asserted
+# bit 11-8: 0, required
+# big 15-11: 0, required
+# bit 19-16: 1, ODT0Wr, MODT[0] asserted during write to DRAM CS0
+# bit 23-20: 0, ODT0Wr, MODT[1] not asserted
+# bit 27-24: 0, required
+# bit 31-28: 0, required
+
+DATA 0xFFD01498 0x00000000 # DDR ODT Control (High)
+# bit 1-0: 0, ODT0 controlled by ODT Control (low) register above
+# bit 3-2: 0, ODT1 controlled by register
+# bit 31-4: 0, required
+
+DATA 0xFFD0149C 0x0000E801 # CPU ODT Control
+# bit 3-0: 1, ODTRd, Internal ODT asserted during read from DRAM bank0
+# bit 7-4: 0, ODTWr, Internal ODT not asserted during write to DRAM
+# bit 9-8: 0, ODTEn, controlled by ODTRd and ODTWr
+# bit 11-10: 2, DQ_ODTSel. ODT select turned on, 75 ohm
+# bit 13-12: 2, STARTBURST ODT buffer selected, 75 ohm
+# bit 14: 1, STARTBURST ODT enabled
+# bit 15: 1, Use ODT Block
+
+DATA 0xFFD01480 0x00000001 # DDR Initialization Control
+# bit 0: 1, enable DDR init upon this register write
+# bit 31-1: 0, reserved
+
+# End of Header extension
+DATA 0x0 0x0
diff --git a/board/keymile/km_arm/km_arm.c b/board/keymile/km_arm/km_arm.c
index 10c9a5f..ff57e60 100644
--- a/board/keymile/km_arm/km_arm.c
+++ b/board/keymile/km_arm/km_arm.c
@@ -134,10 +134,11 @@ int startup_allowed(void)
}
#endif
-#if (defined(CONFIG_MGCOGE3UN)|defined(CONFIG_PORTL2))
+#if (defined(CONFIG_MGCOGE3UN)|defined(CONFIG_PORTL2)| \
+ defined(CONFIG_KM_PIGGY4_88E6352))
/*
- * These two boards have always ethernet present. Its connected to the mv
- * switch.
+ * All boards with PIGGY4 connected via a simple switch have ethernet always
+ * present.
*/
int ethernet_present(void)
{
@@ -367,7 +368,7 @@ void reset_phy(void)
/* reset the phy */
miiphy_reset(name, CONFIG_PHY_BASE_ADR);
}
-#else
+#elif !defined(CONFIG_KM_PIGGY4_88E6352)
/* Configure and enable MV88E1118 PHY on the piggy*/
void reset_phy(void)
{
diff --git a/boards.cfg b/boards.cfg
index 08ac582..869d181 100644
--- a/boards.cfg
+++ b/boards.cfg
@@ -139,6 +139,7 @@ calimain arm arm926ejs calimain omicron
dns325 arm arm926ejs - d-link kirkwood
km_kirkwood arm arm926ejs km_arm keymile kirkwood km_kirkwood:KM_KIRKWOOD,KM_DISABLE_PCI
km_kirkwood_pci arm arm926ejs km_arm keymile kirkwood km_kirkwood:KM_KIRKWOOD_PCI,KM_RECONFIG_XLX
+kmnusa arm arm926ejs km_arm keymile kirkwood km_kirkwood:KM_NUSA
mgcoge3un arm arm926ejs km_arm keymile kirkwood
portl2 arm arm926ejs km_arm keymile kirkwood
inetspace_v2 arm arm926ejs netspace_v2 LaCie kirkwood lacie_kw:INETSPACE_V2
diff --git a/include/configs/km/km_arm.h b/include/configs/km/km_arm.h
index edb8f4e..5f05e8f 100644
--- a/include/configs/km/km_arm.h
+++ b/include/configs/km/km_arm.h
@@ -57,6 +57,13 @@
#define CONFIG_CMD_SF
#define CONFIG_SOFT_I2C /* I2C bit-banged */
+#if defined CONFIG_KM_ENV_IS_IN_SPI_NOR
+#define CONFIG_ENV_SPI_BUS 0
+#define CONFIG_ENV_SPI_CS 0
+#define CONFIG_ENV_SPI_MAX_HZ 5000000
+#define CONFIG_ENV_SPI_MODE SPI_MODE_3
+#endif
+
#include "asm/arch/config.h"
#define CONFIG_SYS_TEXT_BASE 0x07d00000 /* code address before reloc */
@@ -211,6 +218,15 @@ int get_scl(void);
/*
* Environment variables configurations
*/
+#if defined CONFIG_KM_ENV_IS_IN_SPI_NOR
+#define CONFIG_ENV_IS_IN_SPI_FLASH /* use SPI-Flash for environment vars */
+#define CONFIG_ENV_OFFSET 0xc0000 /* no bracets! */
+#define CONFIG_ENV_SIZE 0x02000 /* Size of Environment */
+#define CONFIG_ENV_SECT_SIZE 0x10000
+#define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET + \
+ CONFIG_ENV_SECT_SIZE)
+#define CONFIG_ENV_TOTAL_SIZE 0x20000 /* no bracets! */
+#else
#define CONFIG_ENV_IS_IN_EEPROM /* use EEPROM for environment vars */
#define CONFIG_SYS_DEF_EEPROM_ADDR 0x50
#define CONFIG_ENV_EEPROM_IS_ON_I2C
@@ -218,11 +234,11 @@ int get_scl(void);
#define CONFIG_ENV_OFFSET 0x0 /* no bracets! */
#define CONFIG_ENV_SIZE (0x2000 - CONFIG_ENV_OFFSET)
#define CONFIG_I2C_ENV_EEPROM_BUS KM_ENV_BUS "\0"
-
-/* offset redund: (CONFIG_ENV_OFFSET + CONFIG_ENV_SIZE) */
-#define CONFIG_SYS_REDUNDAND_ENVIRONMENT
#define CONFIG_ENV_OFFSET_REDUND 0x2000 /* no bracets! */
#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE)
+#endif
+
+#define CONFIG_SYS_REDUNDAND_ENVIRONMENT
#define CONFIG_SPI_FLASH
#define CONFIG_SPI_FLASH_STMICRO
@@ -240,17 +256,27 @@ int get_scl(void);
"sf probe 0;sf erase 0 50000;" \
"sf write ${load_addr_r} 0 ${filesize};\0"
-/*
- * Default environment variables
- */
-#define CONFIG_EXTRA_ENV_SETTINGS \
- CONFIG_KM_DEF_ENV \
+#if defined CONFIG_KM_ENV_IS_IN_SPI_NOR
+#define CONFIG_KM_NEW_ENV \
+ "newenv=sf probe 0;" \
+ "sf erase " xstr(CONFIG_ENV_OFFSET) " " \
+ xstr(CONFIG_ENV_TOTAL_SIZE)"\0"
+#else
+#define CONFIG_KM_NEW_ENV \
"newenv=setenv addr 0x100000 && " \
"i2c dev 1; mw.b ${addr} 0 4 && " \
"eeprom write " xstr(CONFIG_SYS_DEF_EEPROM_ADDR) \
" ${addr} " xstr(CONFIG_ENV_OFFSET) " 4 && " \
"eeprom write " xstr(CONFIG_SYS_DEF_EEPROM_ADDR) \
- " ${addr} " xstr(CONFIG_ENV_OFFSET_REDUND) " 4\0" \
+ " ${addr} " xstr(CONFIG_ENV_OFFSET_REDUND) " 4\0"
+#endif
+
+/*
+ * Default environment variables
+ */
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ CONFIG_KM_DEF_ENV \
+ CONFIG_KM_NEW_ENV \
"arch=arm\0" \
"EEprom_ivm=" KM_IVM_BUS "\0" \
""
diff --git a/include/configs/km_kirkwood.h b/include/configs/km_kirkwood.h
index f639edc..97aa617 100644
--- a/include/configs/km_kirkwood.h
+++ b/include/configs/km_kirkwood.h
@@ -6,8 +6,9 @@
* (C) Copyright 2009
* Stefan Roese, DENX Software Engineering, sr at denx.de.
*
- * (C) Copyright 2011
- * Holger Brunck, Keymile GmbH Hannover, holger.brunck at keymile.de
+ * (C) Copyright 2011-2012
+ * Holger Brunck, Keymile GmbH Hannover, holger.brunck at keymile.com
+ * Valentin Longchamp, Keymile AG, valentin.longchamp at keymile.com
*
* See file CREDITS for list of people who contributed to this
* project.
@@ -36,23 +37,67 @@
#ifndef _CONFIG_KM_KIRKWOOD_H
#define _CONFIG_KM_KIRKWOOD_H
-/* include common defines/options for all arm based Keymile boards */
-#include "km/km_arm.h"
-
-/*
- * Version number information
- */
#if defined(CONFIG_KM_KIRKWOOD)
-#define CONFIG_IDENT_STRING "\nKeymile Kirkwood"
+#define CONFIG_IDENT_STRING "\nKeymile Kirkwood"
#undef CONFIG_KIRKWOOD_PCIE_INIT
+#define KM_IVM_BUS "pca9544a:70:9" /* I2C2 (Mux-Port 1)*/
#elif defined(CONFIG_KM_KIRKWOOD_PCI)
-#define CONFIG_IDENT_STRING "\nKeymile Kirkwood PCI"
+#define CONFIG_IDENT_STRING "\nKeymile Kirkwood PCI"
+#define KM_IVM_BUS "pca9544a:70:9" /* I2C2 (Mux-Port 1)*/
+/* KM_NUSA */
+#elif defined(CONFIG_KM_NUSA)
+#define KM_IVM_BUS "pca9547:70:9" /* I2C2 (Mux-Port 1)*/
+#define CONFIG_IDENT_STRING "\nKeymile NUSA"
+#undef CONFIG_SYS_KWD_CONFIG
+#define CONFIG_SYS_KWD_CONFIG \
+ $(SRCTREE)/$(CONFIG_BOARDDIR)/128M16-1.cfg
+#define CONFIG_KM_ENV_IS_IN_SPI_NOR
+#define CONFIG_KM_FPGA_CONFIG
+#define CONFIG_KM_PIGGY4_88E6352
+
+#else
+#error ("Board unsupported")
#endif
+/* include common defines/options for all arm based Keymile boards */
+#include "km/km_arm.h"
+
#define CONFIG_HOSTNAME km_kirkwood
-#define KM_IVM_BUS "pca9544a:70:9" /* I2C2 (Mux-Port 1)*/
+#ifndef CONFIG_KM_ENV_IS_IN_SPI_NOR
#define KM_ENV_BUS "pca9544a:70:d" /* I2C2 (Mux-Port 5)*/
+#endif
+
+#if defined(CONFIG_KM_PIGGY4_88E6352)
+/*
+ * Some keymile boards like mgcoge5un & nusa1 have their PIGGY4 connected via
+ * an Marvell 88E6352 simple switch.
+ * In this case we have to change the default settings for the etherent mac.
+ * There is NO ethernet phy. The ARM and Switch are conencted directly over
+ * RGMII in MAC-MAC mode
+ * In this case 1GBit full duplex and autoneg off
+ */
+#define PORT_SERIAL_CONTROL_VALUE ( \
+ MVGBE_FORCE_LINK_PASS | \
+ MVGBE_DIS_AUTO_NEG_FOR_DUPLX | \
+ MVGBE_DIS_AUTO_NEG_FOR_FLOW_CTRL | \
+ MVGBE_ADV_NO_FLOW_CTRL | \
+ MVGBE_FORCE_FC_MODE_NO_PAUSE_DIS_TX | \
+ MVGBE_FORCE_BP_MODE_NO_JAM | \
+ (1 << 9) /* Reserved bit has to be 1 */ | \
+ MVGBE_DO_NOT_FORCE_LINK_FAIL | \
+ MVGBE_DIS_AUTO_NEG_SPEED_GMII | \
+ MVGBE_DTE_ADV_0 | \
+ MVGBE_MIIPHY_MAC_MODE | \
+ MVGBE_AUTO_NEG_NO_CHANGE | \
+ MVGBE_MAX_RX_PACKET_1552BYTE | \
+ MVGBE_CLR_EXT_LOOPBACK | \
+ MVGBE_SET_FULL_DUPLEX_MODE | \
+ MVGBE_EN_FLOW_CTRL_TX_RX_IN_FULL_DUPLEX |\
+ MVGBE_SET_GMII_SPEED_TO_1000 |\
+ MVGBE_SET_MII_SPEED_TO_100)
+
+#endif
/* GPIO Pin from kirkwood connected to PROGRAM_B pin of the xilinx FPGA */
#define KM_XLX_PROGRAM_B_PIN 39
--
1.7.1
More information about the U-Boot
mailing list