[U-Boot] [PATCH V1 RESEND 04/12] st_smi: Enhance the error handling

[Amit Virdi]

This commit does the following:
 - Reports error if SNOR flash is not found on the board
 - Changes smi_read_sr to return error using which a retry mechanism is
   implemented for reading flash status

Signed-off-by: Vipin Kumar <vipin.kumar at st.com>
Signed-off-by: Amit Virdi <amit.virdi at st.com>
---
 drivers/mtd/st_smi.c |   34 +++++++++++++++++++++-------------
 1 files changed, 21 insertions(+), 13 deletions(-)

diff --git a/drivers/mtd/st_smi.c b/drivers/mtd/st_smi.c
index ec19b0d..ce50fc1 100644
--- a/drivers/mtd/st_smi.c
+++ b/drivers/mtd/st_smi.c
@@ -108,11 +108,17 @@ static ulong flash_get_size(ulong base, int banknum)
 {
 	flash_info_t *info = &flash_info[banknum];
 	struct flash_dev *dev;
-	unsigned int value;
+	int value;
 	unsigned int density;
 	int i;
 
 	value = smi_read_id(info, banknum);
+
+	if (value < 0) {
+		printf("Flash id could not be read\n");
+		return 0;
+	}
+
 	density = (value >> 16) & 0xff;
 
 	for (i = 0, dev = &flash_ids[0]; dev->density != 0x0;
@@ -140,7 +146,7 @@ static ulong flash_get_size(ulong base, int banknum)
  * This routine will get the status register of the flash chip present at the
  * given bank
  */
-static unsigned int smi_read_sr(int bank)
+static int smi_read_sr(int bank)
 {
 	u32 ctrlreg1;
 
@@ -174,13 +180,11 @@ static unsigned int smi_read_sr(int bank)
  */
 static int smi_wait_till_ready(int bank, int timeout)
 {
-	int count;
-	unsigned int sr;
+	int sr;
 
 	/* One chip guarantees max 5 msec wait here after page writes,
 	   but potentially three seconds (!) after page erase. */
-	for (count = 0; count < timeout; count++) {
-
+	do {
 		sr = smi_read_sr(bank);
 		if (sr < 0)
 			break;
@@ -189,7 +193,8 @@ static int smi_wait_till_ready(int bank, int timeout)
 
 		/* Try again after 1m-sec */
 		udelay(1000);
-	}
+	} while (timeout--);
+
 	printf("SMI controller is still in wait, timeout=%d\n", timeout);
 	return -EIO;
 }
@@ -205,6 +210,7 @@ static int smi_write_enable(int bank)
 {
 	u32 ctrlreg1;
 	int timeout = WMODE_TOUT;
+	int sr;
 
 	/* Store the CTRL REG1 state */
 	ctrlreg1 = readl(&smicntl->smi_cr1);
@@ -221,14 +227,16 @@ static int smi_write_enable(int bank)
 	/* Restore the CTRL REG1 state */
 	writel(ctrlreg1, &smicntl->smi_cr1);
 
-	while (timeout--) {
-		if (smi_read_sr(bank) & (1 << (bank + WM_SHIFT)))
+	do {
+		sr = smi_read_sr(bank);
+		if (sr < 0)
 			break;
-		udelay(1000);
-	}
+		else if (sr & (1 << (bank + WM_SHIFT)))
+			return 0;
 
-	if (timeout)
-		return 0;
+		/* Try again after 1m-sec */
+		udelay(1000);
+	} while (timeout--);
 
 	return -1;
 }
-- 
1.7.2.2