[U-Boot] [PATCH] ATMEL/PIO: Enable new feature of PIO on Atmel device
Bo Shen
voice.shen at atmel.com
Mon May 14 11:00:16 CEST 2012
Enable new PIO feature supported by Atmel SoC.
Using CPU_HAS_PIO3 micro to enable PIO new feature.
Signed-off-by: Bo Shen <voice.shen at atmel.com>
---
arch/arm/include/asm/arch-at91/at91_pio.h | 71 ++++++++++++++++-
drivers/gpio/at91_gpio.c | 123 ++++++++++++++++++++++++++++-
2 files changed, 191 insertions(+), 3 deletions(-)
diff --git a/arch/arm/include/asm/arch-at91/at91_pio.h b/arch/arm/include/asm/arch-at91/at91_pio.h
index 416cabf..4ceedee 100644
--- a/arch/arm/include/asm/arch-at91/at91_pio.h
+++ b/arch/arm/include/asm/arch-at91/at91_pio.h
@@ -66,14 +66,50 @@ typedef struct at91_port {
u32 puer; /* 0x64 Pull-up Enable Register */
u32 pusr; /* 0x68 Pad Pull-up Status Register */
u32 reserved4;
+#if defined(CPU_HAS_PIO3)
+ u32 abcdsr1; /* 0x70 Peripheral ABCD Select Register 1 */
+ u32 abcdsr2; /* 0x74 Peripheral ABCD Select Register 2 */
+ u32 reserved5[2];
+ u32 ifscdr; /* 0x80 Input Filter SCLK Disable Register */
+ u32 ifscer; /* 0x84 Input Filter SCLK Enable Register */
+ u32 ifscsr; /* 0x88 Input Filter SCLK Status Register */
+ u32 scdr; /* 0x8C SCLK Divider Debouncing Register */
+ u32 ppddr; /* 0x90 Pad Pull-down Disable Register */
+ u32 ppder; /* 0x94 Pad Pull-down Enable Register */
+ u32 ppdsr; /* 0x98 Pad Pull-down Status Register */
+ u32 reserved6; /* */
+#else
u32 asr; /* 0x70 Select A Register */
u32 bsr; /* 0x74 Select B Register */
u32 absr; /* 0x78 AB Select Status Register */
u32 reserved5[9]; /* */
+#endif
u32 ower; /* 0xA0 Output Write Enable Register */
u32 owdr; /* 0xA4 Output Write Disable Register */
- u32 owsr; /* OxA8 utput Write Status Register */
+ u32 owsr; /* OxA8 Output Write Status Register */
+#if defined(CPU_HAS_PIO3)
+ u32 reserved7; /* */
+ u32 aimer; /* 0xB0 Additional INT Modes Enable Register */
+ u32 aimdr; /* 0xB4 Additional INT Modes Disable Register */
+ u32 aimmr; /* 0xB8 Additional INT Modes Mask Register */
+ u32 reserved8; /* */
+ u32 esr; /* 0xC0 Edge Select Register */
+ u32 lsr; /* 0xC4 Level Select Register */
+ u32 elsr; /* 0xC8 Edge/Level Status Register */
+ u32 reserved9; /* 0xCC */
+ u32 fellsr; /* 0xD0 Falling /Low Level Select Register */
+ u32 rehlsr; /* 0xD4 Rising /High Level Select Register */
+ u32 frlhsr; /* 0xD8 Fall/Rise - Low/High Status Register */
+ u32 reserved10; /* */
+ u32 locksr; /* 0xE0 Lock Status */
+ u32 wpmr; /* 0xE4 Write Protect Mode Register */
+ u32 wpsr; /* 0xE8 Write Protect Status Register */
+ u32 reserved11[5]; /* */
+ u32 schmitt; /* 0x100 Schmitt Trigger Register */
+ u32 reserved12[63];
+#else
u32 reserved6[85];
+#endif
} at91_port_t;
typedef union at91_pio {
@@ -94,6 +130,13 @@ typedef union at91_pio {
#ifdef CONFIG_AT91_GPIO
int at91_set_a_periph(unsigned port, unsigned pin, int use_pullup);
int at91_set_b_periph(unsigned port, unsigned pin, int use_pullup);
+#if defined(CPU_HAS_PIO3)
+int at91_set_c_periph(unsigned port, unsigned pin, int use_pullup);
+int at91_set_d_periph(unsigned port, unsigned pin, int use_pullup);
+int at91_set_pio_debounce(unsigned port, unsigned pin, int is_on, int div);
+int at91_set_pio_pulldown(unsigned port, unsigned pin, int is_on);
+int at91_set_pio_disable_schmitt_trig(unsigned port, unsigned pin);
+#endif
int at91_set_pio_input(unsigned port, unsigned pin, int use_pullup);
int at91_set_pio_multi_drive(unsigned port, unsigned pin, int is_on);
int at91_set_pio_output(unsigned port, unsigned pin, int value);
@@ -137,11 +180,37 @@ int at91_get_pio_value(unsigned port, unsigned pin);
#define PIO_PUER 0x64 /* Pull-up Enable Register */
#define PIO_PUSR 0x68 /* Pull-up Status Register */
#define PIO_ASR 0x70 /* Peripheral A Select Register */
+#define PIO_ABCDSR1 0x70 /* Peripheral ABCD Select Register 1 */
#define PIO_BSR 0x74 /* Peripheral B Select Register */
+#define PIO_ABCDSR2 0x74 /* Peripheral ABCD Select Register 2 */
#define PIO_ABSR 0x78 /* AB Status Register */
+#define PIO_IFSCDR 0x80 /* Input Filter Slow Clock Disable Register */
+#define PIO_IFSCER 0x84 /* Input Filter Slow Clock Enable Register */
+#define PIO_IFSCSR 0x88 /* Input Filter Slow Clock Status Register */
+#define PIO_SCDR 0x8c /* Slow Clock Divider Debouncing Register */
+#define PIO_SCDR_DIV (0x3fff << 0) /* Slow Clock Divider Mask */
+#define PIO_PPDDR 0x90 /* Pad Pull-down Disable Register */
+#define PIO_PPDER 0x94 /* Pad Pull-down Enable Register */
+#define PIO_PPDSR 0x98 /* Pad Pull-down Status Register */
#define PIO_OWER 0xa0 /* Output Write Enable Register */
#define PIO_OWDR 0xa4 /* Output Write Disable Register */
#define PIO_OWSR 0xa8 /* Output Write Status Register */
+#define PIO_AIMER 0xb0 /* Additional INT Modes Enable Register */
+#define PIO_AIMDR 0xb4 /* Additional INT Modes Disable Register */
+#define PIO_AIMMR 0xb8 /* Additional INT Modes Mask Register */
+#define PIO_ESR 0xc0 /* Edge Select Register */
+#define PIO_LSR 0xc4 /* Level Select Register */
+#define PIO_ELSR 0xc8 /* Edge/Level Status Register */
+#define PIO_FELLSR 0xd0 /* Falling Edge/Low Level Select Register */
+#define PIO_REHLSR 0xd4 /* Rising Edge/ High Level Select Register */
+#define PIO_FRLHSR 0xd8 /* Fall/Rise - Low/High Status Register */
+#define PIO_SCHMITT 0x100 /* Schmitt Trigger Register */
+
+#define ABCDSR_PERIPH_A 0x0
+#define ABCDSR_PERIPH_B 0x1
+#define ABCDSR_PERIPH_C 0x2
+#define ABCDSR_PERIPH_D 0x3
+
#endif
#endif
diff --git a/drivers/gpio/at91_gpio.c b/drivers/gpio/at91_gpio.c
index be2a026..64dfd6c 100644
--- a/drivers/gpio/at91_gpio.c
+++ b/drivers/gpio/at91_gpio.c
@@ -86,7 +86,14 @@ int at91_set_a_periph(unsigned port, unsigned pin, int use_pullup)
mask = 1 << pin;
writel(mask, &pio->port[port].idr);
at91_set_pio_pullup(port, pin, use_pullup);
+#if defined(CPU_HAS_PIO3)
+ writel(readl(&pio->port[port].abcdsr1) & ~mask,
+ &pio->port[port].abcdsr1);
+ writel(readl(&pio->port[port].abcdsr2) & ~mask,
+ &pio->port[port].abcdsr2);
+#else
writel(mask, &pio->port[port].asr);
+#endif
writel(mask, &pio->port[port].pdr);
}
return 0;
@@ -104,12 +111,63 @@ int at91_set_b_periph(unsigned port, unsigned pin, int use_pullup)
mask = 1 << pin;
writel(mask, &pio->port[port].idr);
at91_set_pio_pullup(port, pin, use_pullup);
+#if defined(CPU_HAS_PIO3)
+ writel(readl(&pio->port[port].abcdsr1) | mask,
+ &pio->port[port].abcdsr1);
+ writel(readl(&pio->port[port].abcdsr2) & ~mask,
+ &pio->port[port].abcdsr2);
+#else
writel(mask, &pio->port[port].bsr);
+#endif
writel(mask, &pio->port[port].pdr);
}
return 0;
}
+#if defined(CPU_HAS_PIO3)
+/*
+ * mux the pin to the "C" internal peripheral role.
+ */
+int at91_set_c_periph(unsigned port, unsigned pin, int use_pullup)
+{
+ at91_pio_t *pio = (at91_pio_t *) ATMEL_BASE_PIOA;
+ u32 mask;
+
+ if ((port < ATMEL_PIO_PORTS) && (pin < 32)) {
+ mask = 1 << pin;
+ writel(mask, &pio->port[port].idr);
+ at91_set_pio_pullup(port, pin, use_pullup);
+ writel(readl(&pio->port[port].abcdsr1) & ~mask,
+ &pio->port[port].abcdsr1);
+ writel(readl(&pio->port[port].abcdsr2) | mask,
+ &pio->port[port].abcdsr2);
+ writel(mask, &pio->port[port].pdr);
+ }
+ return 0;
+}
+
+/*
+ * mux the pin to the "D" internal peripheral role.
+ */
+int at91_set_d_periph(unsigned port, unsigned pin, int use_pullup)
+{
+ at91_pio_t *pio = (at91_pio_t *) ATMEL_BASE_PIOA;
+ u32 mask;
+
+ if ((port < ATMEL_PIO_PORTS) && (pin < 32)) {
+ mask = 1 << pin;
+ writel(mask, &pio->port[port].idr);
+ at91_set_pio_pullup(port, pin, use_pullup);
+ writel(readl(&pio->port[port].abcdsr1) | mask,
+ &pio->port[port].abcdsr1);
+ writel(readl(&pio->port[port].abcdsr2) | mask,
+ &pio->port[port].abcdsr2);
+ writel(mask, &pio->port[port].pdr);
+ }
+ return 0;
+}
+#endif
+
/*
* mux the pin to the gpio controller (instead of "A" or "B" peripheral), and
* configure it for an input.
@@ -162,14 +220,75 @@ int at91_set_pio_deglitch(unsigned port, unsigned pin, int is_on)
if ((port < ATMEL_PIO_PORTS) && (pin < 32)) {
mask = 1 << pin;
- if (is_on)
+ if (is_on) {
+#if defined(CPU_HAS_PIO3)
+ writel(mask, &pio->port[port].ifscdr);
+#endif
writel(mask, &pio->port[port].ifer);
- else
+ } else
writel(mask, &pio->port[port].ifdr);
}
return 0;
}
+#if defined(CPU_HAS_PIO3)
+/*
+ * enable/disable the debounce filter.
+ */
+int at91_set_pio_debounce(unsigned port, unsigned pin, int is_on, int div)
+{
+ at91_pio_t *pio = (at91_pio_t *) ATMEL_BASE_PIOA;
+ u32 mask;
+
+ if ((port < ATMEL_PIO_PORTS) && (pin < 32)) {
+ mask = 1 << pin;
+ if (is_on) {
+ writel(mask, &pio->port[port].ifscer);
+ writel(div & PIO_SCDR_DIV, &pio->port[port].scdr);
+ writel(mask, &pio->port[port].ifer);
+ } else
+ writel(mask, &pio->port[port].ifdr);
+ }
+ return 0;
+}
+
+/*
+ * enable/disable the pull-down.
+ * If pull-up already enabled while calling the function, we disable it.
+ */
+int at91_set_pio_pulldown(unsigned port, unsigned pin, int is_on)
+{
+ at91_pio_t *pio = (at91_pio_t *) ATMEL_BASE_PIOA;
+ u32 mask;
+
+ if ((port < ATMEL_PIO_PORTS) && (pin < 32)) {
+ mask = 1 << pin;
+ writel(mask, &pio->port[port].pudr);
+ if (is_on)
+ writel(mask, &pio->port[port].ppder);
+ else
+ writel(mask, &pio->port[port].ppddr);
+ }
+ return 0;
+}
+
+/*
+ * disable Schmitt trigger
+ */
+int at91_set_pio_disable_schmitt_trig(unsigned port, unsigned pin)
+{
+ at91_pio_t *pio = (at91_pio_t *) ATMEL_BASE_PIOA;
+ u32 mask;
+
+ if ((port < ATMEL_PIO_PORTS) && (pin < 32)) {
+ mask = 1 << pin;
+ writel(readl(&pio->port[port].schmitt) | mask,
+ &pio->port[port].schmitt);
+ }
+ return 0;
+}
+#endif
+
/*
* enable/disable the multi-driver. This is only valid for output and
* allows the output pin to run as an open collector output.
--
1.7.10
More information about the U-Boot
mailing list