[U-Boot] [PATCH v4 13/27] arm/km: convert mgcoge3un target to km_kirkwood
Valentin Longchamp
valentin.longchamp at keymile.com
Tue May 15 16:10:50 CEST 2012
From: Holger Brunck <holger.brunck at keymile.com>
Use the generic header km_kirkwood.h and get rid of the
board specific header.
Signed-off-by: Holger Brunck <holger.brunck at keymile.com>
Signed-off-by: Valentin Longchamp <valentin.longchamp at keymile.com>
cc: Gerlando Falauto <gerlando.falauto at keymile.com>
cc: Prafulla Wadaskar <prafulla at marvell.com>
---
board/keymile/km_arm/km_arm.c | 9 ++--
boards.cfg | 2 +-
include/configs/km_kirkwood.h | 46 +++++++++++++++++++++
include/configs/mgcoge3un.h | 87 -----------------------------------------
4 files changed, 51 insertions(+), 93 deletions(-)
delete mode 100644 include/configs/mgcoge3un.h
diff --git a/board/keymile/km_arm/km_arm.c b/board/keymile/km_arm/km_arm.c
index bd002b0..18cb24c 100644
--- a/board/keymile/km_arm/km_arm.c
+++ b/board/keymile/km_arm/km_arm.c
@@ -113,7 +113,7 @@ u32 kwmpp_config[] = {
0
};
-#if defined(CONFIG_MGCOGE3UN)
+#if defined(CONFIG_KM_MGCOGE3UN)
/*
* Wait for startup OK from mgcoge3ne
*/
@@ -133,8 +133,7 @@ int startup_allowed(void)
}
#endif
-#if (defined(CONFIG_MGCOGE3UN)|defined(CONFIG_PORTL2)| \
- defined(CONFIG_KM_PIGGY4_88E6352))
+#if (defined(CONFIG_KM_PIGGY4_88E6061)|defined(CONFIG_KM_PIGGY4_88E6352))
/*
* All boards with PIGGY4 connected via a simple switch have ethernet always
* present.
@@ -202,7 +201,7 @@ int misc_init_r(void)
printf("Overwriting MACH_TYPE with %d!!!\n", mach_type);
gd->bd->bi_arch_number = mach_type;
}
-#if defined(CONFIG_MGCOGE3UN)
+#if defined(CONFIG_KM_MGCOGE3UN)
char *wait_for_ne;
wait_for_ne = getenv("waitforne");
if (wait_for_ne != NULL) {
@@ -349,7 +348,7 @@ void dram_init_banksize(void)
}
}
-#if (defined(CONFIG_MGCOGE3UN)|defined(CONFIG_PORTL2))
+#if (defined(CONFIG_KM_MGCOGE3UN)|defined(CONFIG_PORTL2))
#define PHY_LED_SEL 0x18
#define PHY_LED0_LINK (0x5)
diff --git a/boards.cfg b/boards.cfg
index d903f03..64b0d69 100644
--- a/boards.cfg
+++ b/boards.cfg
@@ -140,7 +140,7 @@ dns325 arm arm926ejs - d-link
km_kirkwood arm arm926ejs km_arm keymile kirkwood km_kirkwood:KM_KIRKWOOD,KM_DISABLE_PCI
km_kirkwood_pci arm arm926ejs km_arm keymile kirkwood km_kirkwood:KM_KIRKWOOD_PCI,KM_RECONFIG_XLX
kmnusa arm arm926ejs km_arm keymile kirkwood km_kirkwood:KM_NUSA
-mgcoge3un arm arm926ejs km_arm keymile kirkwood
+mgcoge3un arm arm926ejs km_arm keymile kirkwood km_kirkwood:KM_MGCOGE3UN
kmcoge5un arm arm926ejs km_arm keymile kirkwood km_kirkwood:KMCOGE5UN
portl2 arm arm926ejs km_arm keymile kirkwood
inetspace_v2 arm arm926ejs netspace_v2 LaCie kirkwood lacie_kw:INETSPACE_V2
diff --git a/include/configs/km_kirkwood.h b/include/configs/km_kirkwood.h
index e6f0e36..d1f3351 100644
--- a/include/configs/km_kirkwood.h
+++ b/include/configs/km_kirkwood.h
@@ -58,6 +58,20 @@
#define CONFIG_KM_FPGA_CONFIG
#define CONFIG_KM_PIGGY4_88E6352
+/* KM_MGCOGE3UN */
+#elif defined(CONFIG_KM_MGCOGE3UN)
+#define CONFIG_IDENT_STRING "\nKeymile COGE3UN"
+#define CONFIG_HOSTNAME mgcoge3un
+#define KM_IVM_BUS "pca9547:70:9" /* I2C2 (Mux-Port 1)*/
+#undef CONFIG_SYS_KWD_CONFIG
+#define CONFIG_SYS_KWD_CONFIG \
+ $(SRCTREE)/$(CONFIG_BOARDDIR)/kwbimage-memphis.cfg
+#define CONFIG_KM_BOARD_EXTRA_ENV "waitforne=true\0"
+#define CONFIG_PIGGY_MAC_ADRESS_OFFSET 3
+#define CONFIG_KM_DISABLE_PCIE
+#define CONFIG_KM_PIGGY4_88E6061
+
+/* KMCOGE5UN */
#elif defined(CONFIG_KMCOGE5UN)
#define CONFIG_IDENT_STRING "\nKeymile COGE5UN"
#define KM_IVM_BUS "pca9547:70:9" /* I2C2 (Mux-Port 1)*/
@@ -111,7 +125,39 @@
#endif
+#ifdef CONFIG_KM_PIGGY4_88E6061
+/*
+ * Some keymile boards like mgcoge3un have their PIGGY4 connected via
+ * an Marvell 88E6061 simple switch.
+ * In this case we have to change the default settings for the
+ * ethernet phy connected to the kirkwood.
+ * In this case 100MB full duplex and autoneg off
+ */
+#define PORT_SERIAL_CONTROL_VALUE ( \
+ MVGBE_FORCE_LINK_PASS | \
+ MVGBE_DIS_AUTO_NEG_FOR_DUPLX | \
+ MVGBE_DIS_AUTO_NEG_FOR_FLOW_CTRL | \
+ MVGBE_ADV_NO_FLOW_CTRL | \
+ MVGBE_FORCE_FC_MODE_NO_PAUSE_DIS_TX | \
+ MVGBE_FORCE_BP_MODE_NO_JAM | \
+ (1 << 9) /* Reserved bit has to be 1 */ | \
+ MVGBE_DO_NOT_FORCE_LINK_FAIL | \
+ MVGBE_DIS_AUTO_NEG_SPEED_GMII | \
+ MVGBE_DTE_ADV_0 | \
+ MVGBE_MIIPHY_MAC_MODE | \
+ MVGBE_AUTO_NEG_NO_CHANGE | \
+ MVGBE_MAX_RX_PACKET_1552BYTE | \
+ MVGBE_CLR_EXT_LOOPBACK | \
+ MVGBE_SET_FULL_DUPLEX_MODE | \
+ MVGBE_DIS_FLOW_CTRL_TX_RX_IN_FULL_DUPLEX |\
+ MVGBE_SET_GMII_SPEED_TO_10_100 |\
+ MVGBE_SET_MII_SPEED_TO_100)
+#endif
+
/* GPIO Pin from kirkwood connected to PROGRAM_B pin of the xilinx FPGA */
#define KM_XLX_PROGRAM_B_PIN 39
+#ifdef CONFIG_KM_DISABLE_PCI
+#undef CONFIG_KIRKWOOD_PCIE_INIT
+#endif
#endif /* _CONFIG_KM_KIRKWOOD */
diff --git a/include/configs/mgcoge3un.h b/include/configs/mgcoge3un.h
deleted file mode 100644
index 156821c..0000000
--- a/include/configs/mgcoge3un.h
+++ /dev/null
@@ -1,87 +0,0 @@
-/*
- * (C) Copyright 2009
- * Marvell Semiconductor <www.marvell.com>
- * Prafulla Wadaskar <prafulla at marvell.com>
- *
- * (C) Copyright 2009
- * Stefan Roese, DENX Software Engineering, sr at denx.de.
- *
- * (C) Copyright 2010-2011
- * Holger Brunck, Keymile GmbH Hannover, holger.brunck at keymile.com
- *
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
- * MA 02110-1301 USA
- */
-
-/* for linking errors see
- * http://lists.denx.de/pipermail/u-boot/2009-July/057350.html */
-
-#ifndef _CONFIG_MGCOGE3UN_H
-#define _CONFIG_MGCOGE3UN_H
-
-/* include common defines/options for all arm based Keymile boards */
-#include "km/km_arm.h"
-
-/*
- * Version number information
- */
-#define CONFIG_IDENT_STRING "\nKeymile MGCOGE3UN"
-#define CONFIG_HOSTNAME mgcoge3un
-#define CONFIG_MGCOGE3UN
-
-#define KM_IVM_BUS "pca9547:70:9" /* I2C2 (Mux-Port 1)*/
-#define KM_ENV_BUS "pca9547:70:d" /* I2C2 (Mux-Port 5)*/
-
-/* we use a new RAM type on mgcoge3un board */
-#undef CONFIG_SYS_KWD_CONFIG
-#define CONFIG_SYS_KWD_CONFIG $(SRCTREE)/$(CONFIG_BOARDDIR)/kwbimage-memphis.cfg
-
-/*
- * mgcoge3un has a fixed link to the marvell switch
- * with 100MB full duplex and autoneg off, for this
- * reason we have to change the default settings
- */
-#define PORT_SERIAL_CONTROL_VALUE ( \
- MVGBE_FORCE_LINK_PASS | \
- MVGBE_DIS_AUTO_NEG_FOR_DUPLX | \
- MVGBE_DIS_AUTO_NEG_FOR_FLOW_CTRL | \
- MVGBE_ADV_NO_FLOW_CTRL | \
- MVGBE_FORCE_FC_MODE_NO_PAUSE_DIS_TX | \
- MVGBE_FORCE_BP_MODE_NO_JAM | \
- (1 << 9) /* Reserved bit has to be 1 */ | \
- MVGBE_DO_NOT_FORCE_LINK_FAIL | \
- MVGBE_DIS_AUTO_NEG_SPEED_GMII | \
- MVGBE_DTE_ADV_0 | \
- MVGBE_MIIPHY_MAC_MODE | \
- MVGBE_AUTO_NEG_NO_CHANGE | \
- MVGBE_MAX_RX_PACKET_1552BYTE | \
- MVGBE_CLR_EXT_LOOPBACK | \
- MVGBE_SET_FULL_DUPLEX_MODE | \
- MVGBE_DIS_FLOW_CTRL_TX_RX_IN_FULL_DUPLEX |\
- MVGBE_SET_GMII_SPEED_TO_10_100 |\
- MVGBE_SET_MII_SPEED_TO_100)
-
-#define CONFIG_KM_BOARD_EXTRA_ENV "waitforne=true\0"
-#define CONFIG_PIGGY_MAC_ADRESS_OFFSET 3
-
-/*
- * PCIe port not used on mgcoge3un
- */
-#undef CONFIG_KIRKWOOD_PCIE_INIT
-
-#endif /* _CONFIG_MGCOGE3UN_H */
--
1.7.1
More information about the U-Boot
mailing list