[U-Boot] [PATCH 3/7] OMAP5: Configure the io settings for omap5432 uevm board
Lokesh Vutla
lokeshvutla at ti.com
Tue May 22 12:03:23 CEST 2012
This patch adds the IO settings required for OMAP5432 uevm's DDR3 pads
Signed-off-by: Lokesh Vutla <lokeshvutla at ti.com>
---
arch/arm/cpu/armv7/omap5/hwinit.c | 98 +++++++++++++++++++++++++------
arch/arm/include/asm/arch-omap5/omap.h | 15 +++++-
2 files changed, 93 insertions(+), 20 deletions(-)
diff --git a/arch/arm/cpu/armv7/omap5/hwinit.c b/arch/arm/cpu/armv7/omap5/hwinit.c
index e2f76a1..df0b760 100644
--- a/arch/arm/cpu/armv7/omap5/hwinit.c
+++ b/arch/arm/cpu/armv7/omap5/hwinit.c
@@ -52,6 +52,81 @@ static struct gpio_bank gpio_bank_54xx[6] = {
const struct gpio_bank *const omap_gpio_bank = gpio_bank_54xx;
#ifdef CONFIG_SPL_BUILD
+/* LPDDR2 specific IO settings */
+static void io_settings_lpddr2(void)
+{
+ struct omap_sys_ctrl_regs *ioregs_base =
+ (struct omap_sys_ctrl_regs *) SYSCTRL_GENERAL_CORE_BASE;
+
+ writel(DDR_IO_I_34OHM_SR_FASTEST_WD_DQ_NO_PULL_DQS_PULL_DOWN,
+ &(ioregs_base->control_ddrch1_0));
+ writel(DDR_IO_I_34OHM_SR_FASTEST_WD_DQ_NO_PULL_DQS_PULL_DOWN,
+ &(ioregs_base->control_ddrch1_1));
+ writel(DDR_IO_I_34OHM_SR_FASTEST_WD_DQ_NO_PULL_DQS_PULL_DOWN,
+ &(ioregs_base->control_ddrch2_0));
+ writel(DDR_IO_I_34OHM_SR_FASTEST_WD_DQ_NO_PULL_DQS_PULL_DOWN,
+ &(ioregs_base->control_ddrch2_1));
+ writel(DDR_IO_I_34OHM_SR_FASTEST_WD_CK_CKE_NCS_CA_PULL_DOWN,
+ &(ioregs_base->control_lpddr2ch1_0));
+ writel(DDR_IO_I_34OHM_SR_FASTEST_WD_CK_CKE_NCS_CA_PULL_DOWN,
+ &(ioregs_base->control_lpddr2ch1_1));
+ writel(DDR_IO_0_DDR2_DQ_INT_EN_ALL_DDR3_CA_DIS_ALL,
+ &(ioregs_base->control_ddrio_0));
+ writel(DDR_IO_1_DQ_OUT_EN_ALL_DQ_INT_EN_ALL,
+ &(ioregs_base->control_ddrio_1));
+ writel(DDR_IO_2_CA_OUT_EN_ALL_CA_INT_EN_ALL,
+ &(ioregs_base->control_ddrio_2));
+}
+
+/* DDR3 specific IO settings */
+static void io_settings_ddr3(void)
+{
+ u32 io_settings = 0;
+ struct omap_sys_ctrl_regs *ioregs_base =
+ (struct omap_sys_ctrl_regs *) SYSCTRL_GENERAL_CORE_BASE;
+
+ writel(DDR_IO_I_40OHM_SR_SLOWEST_WD_DQ_NO_PULL_DQS_NO_PULL,
+ &(ioregs_base->control_ddr3ch1_0));
+ writel(DDR_IO_I_40OHM_SR_FAST_WD_DQ_NO_PULL_DQS_NO_PULL,
+ &(ioregs_base->control_ddrch1_0));
+ writel(DDR_IO_I_40OHM_SR_FAST_WD_DQ_NO_PULL_DQS_NO_PULL,
+ &(ioregs_base->control_ddrch1_1));
+
+ writel(DDR_IO_I_40OHM_SR_SLOWEST_WD_DQ_NO_PULL_DQS_NO_PULL,
+ &(ioregs_base->control_ddr3ch2_0));
+ writel(DDR_IO_I_40OHM_SR_FAST_WD_DQ_NO_PULL_DQS_NO_PULL,
+ &(ioregs_base->control_ddrch2_0));
+ writel(DDR_IO_I_40OHM_SR_FAST_WD_DQ_NO_PULL_DQS_NO_PULL,
+ &(ioregs_base->control_ddrch2_1));
+
+ writel(DDR_IO_0_VREF_CELLS_DDR3_VALUE,
+ &(ioregs_base->control_ddrio_0));
+ writel(DDR_IO_1_VREF_CELLS_DDR3_VALUE,
+ &(ioregs_base->control_ddrio_1));
+ writel(DDR_IO_2_VREF_CELLS_DDR3_VALUE,
+ &(ioregs_base->control_ddrio_2));
+
+ /* omap5432 does not use lpddr2 */
+ writel(0x0, &(ioregs_base->control_lpddr2ch1_0));
+ writel(0x0, &(ioregs_base->control_lpddr2ch1_1));
+
+ writel(SDRAM_CONFIG_EXT_RD_LVL_11_SAMPLES,
+ &(ioregs_base->control_emif1_sdram_config_ext));
+ writel(SDRAM_CONFIG_EXT_RD_LVL_11_SAMPLES,
+ &(ioregs_base->control_emif2_sdram_config_ext));
+
+ /* Disable DLL select */
+ io_settings = (readl(&(ioregs_base->control_port_emif1_sdram_config))
+ & 0xFFEFFFFF);
+ writel(io_settings,
+ &(ioregs_base->control_port_emif1_sdram_config));
+
+ io_settings = (readl(&(ioregs_base->control_port_emif2_sdram_config))
+ & 0xFFEFFFFF);
+ writel(io_settings,
+ &(ioregs_base->control_port_emif2_sdram_config));
+}
+
/*
* Some tuning of IOs for optimal power and performance
*/
@@ -115,25 +190,10 @@ void do_io_settings(void)
(sc_fast << 17) | (sc_fast << 14);
writel(io_settings, &(ioregs_base->control_smart3io_padconf_1));
- /* LPDDR2 io settings */
- writel(DDR_IO_I_34OHM_SR_FASTEST_WD_DQ_NO_PULL_DQS_PULL_DOWN,
- &(ioregs_base->control_ddrch1_0));
- writel(DDR_IO_I_34OHM_SR_FASTEST_WD_DQ_NO_PULL_DQS_PULL_DOWN,
- &(ioregs_base->control_ddrch1_1));
- writel(DDR_IO_I_34OHM_SR_FASTEST_WD_DQ_NO_PULL_DQS_PULL_DOWN,
- &(ioregs_base->control_ddrch2_0));
- writel(DDR_IO_I_34OHM_SR_FASTEST_WD_DQ_NO_PULL_DQS_PULL_DOWN,
- &(ioregs_base->control_ddrch2_1));
- writel(DDR_IO_I_34OHM_SR_FASTEST_WD_CK_CKE_NCS_CA_PULL_DOWN,
- &(ioregs_base->control_lpddr2ch1_0));
- writel(DDR_IO_I_34OHM_SR_FASTEST_WD_CK_CKE_NCS_CA_PULL_DOWN,
- &(ioregs_base->control_lpddr2ch1_1));
- writel(DDR_IO_0_DDR2_DQ_INT_EN_ALL_DDR3_CA_DIS_ALL,
- &(ioregs_base->control_ddrio_0));
- writel(DDR_IO_1_DQ_OUT_EN_ALL_DQ_INT_EN_ALL,
- &(ioregs_base->control_ddrio_1));
- writel(DDR_IO_2_CA_OUT_EN_ALL_CA_INT_EN_ALL,
- &(ioregs_base->control_ddrio_2));
+ if (omap_revision() <= OMAP5430_ES1_0)
+ io_settings_lpddr2();
+ else
+ io_settings_ddr3();
/* Efuse settings */
writel(EFUSE_1, &(ioregs_base->control_efuse_1));
diff --git a/arch/arm/include/asm/arch-omap5/omap.h b/arch/arm/include/asm/arch-omap5/omap.h
index 0a4c8ec..f0658d0 100644
--- a/arch/arm/include/asm/arch-omap5/omap.h
+++ b/arch/arm/include/asm/arch-omap5/omap.h
@@ -179,7 +179,14 @@ struct omap_sys_ctrl_regs {
u32 control_srcomp_east_side; /*0x4A002E7C*/
u32 control_srcomp_west_side; /*0x4A002E80*/
u32 control_srcomp_code_latch; /*0x4A002E84*/
- u32 pad4[3680198];
+ u32 pad4[3679394];
+ u32 control_port_emif1_sdram_config; /*0x4AE0C110*/
+ u32 control_port_emif1_lpddr2_nvm_config; /*0x4AE0C114*/
+ u32 control_port_emif2_sdram_config; /*0x4AE0C118*/
+ u32 pad5[10];
+ u32 control_emif1_sdram_config_ext; /* 0x4AE0C144 */
+ u32 control_emif2_sdram_config_ext; /* 0x4AE0C148 */
+ u32 pad6[789];
u32 control_smart1nopmio_padconf_0; /* 0x4AE0CDA0 */
u32 control_smart1nopmio_padconf_1; /* 0x4AE0CDA4 */
u32 control_padconf_mode; /* 0x4AE0CDA8 */
@@ -234,6 +241,12 @@ struct omap_sys_ctrl_regs {
#define DDR_IO_1_DQ_OUT_EN_ALL_DQ_INT_EN_ALL 0x8421084
#define DDR_IO_2_CA_OUT_EN_ALL_CA_INT_EN_ALL 0x8421000
+#define DDR_IO_I_40OHM_SR_SLOWEST_WD_DQ_NO_PULL_DQS_NO_PULL 0x7C7C7C6C
+#define DDR_IO_I_40OHM_SR_FAST_WD_DQ_NO_PULL_DQS_NO_PULL 0x64646464
+#define DDR_IO_0_VREF_CELLS_DDR3_VALUE 0xBAE8C631
+#define DDR_IO_1_VREF_CELLS_DDR3_VALUE 0xBC6318DC
+#define DDR_IO_2_VREF_CELLS_DDR3_VALUE 0x0
+
#define EFUSE_1 0x45145100
#define EFUSE_2 0x45145100
#define EFUSE_3 0x45145100
--
1.7.5.4
More information about the U-Boot
mailing list