[U-Boot] SMSC LAN9514 on TI DM37x board

Felix Radensky felix at embedded-sol.com
Tue Nov 6 09:24:32 CET 2012


Hi Marek,

On 11/06/2012 12:57 AM, Marek Vasut wrote:
> Can you please avoid top-posting? Does U-Boot even support your USB device?
>

Sorry about top-posting. My USB device is supported by smsc95xx.c driver
in drivers/usb/eth.
>> Thanks a lot.
>>
>> Felix.
>>
>> On 11/02/2012 08:38 AM, Felix Radensky wrote:
>>> Hi,
>>>
>>> I'm running u-boot-2012.10 on a custom DM37x based board.
>>> The board has LAN9514 USB Ethernet adapter connected
>>> in EHCI host controller via USB3320 ULPI PHY. This is very
>>> similar to BeagleBoard XM. Both Ethernet and USB hub work
>>> in linux-2.6.37 from TI PSP 04.02.00.07. In u-boot however,
>>> neither Ethernet nor mass storage devices attached to hub
>>> are not detected.
>>>
>>> Below is boot log:
>>>
>>> U-Boot 2012.10 (Nov 02 2012 - 00:44:41)
>>>
>>> OMAP36XX/37XX-GP ES1.2, CPU-OPP2, L3-165MHz, Max CPU Clock 1 Ghz
>>> Pro4Tech MVC404 board + LPDDR/NAND
>>> I2C:   ready
>>> DRAM:  256 MiB
>>> NAND:  512 MiB
>>> MMC:   OMAP SD/MMC: 0
>>> In:    serial
>>> Out:   serial
>>> Err:   serial
>>> Net:   Net Initialization Skipped
>>> No ethernet found.
>>> Hit any key to stop autoboot:  0
>>> MVC404>  usb start
>>> (Re)start USB...
>>> USB:   Register 1313 NbrPorts 3
>>> USB EHCI 1.00
>>> scanning bus for devices... 1 USB Device(s) found
>>>
>>>         scanning bus for storage devices... 0 Storage Device(s) found
>>>         scanning bus for ethernet devices... 0 Ethernet Device(s) found
>>>
>>> MVC404>  usb info
>>> 1: Hub,  USB Revision 2.0
>>>
>>>   - u-boot EHCI Host Controller
>>>   - Class: Hub
>>>   - PacketSize: 64  Configurations: 1
>>>   - Vendor: 0x0000  Product 0x0000 Version 1.0
>>>
>>>     Configuration: 1
>>>     - Interfaces: 1 Self Powered 0mA
>>>
>>>       Interface: 0
>>>       - Alternate Setting 0, Endpoints: 1
>>>       - Class Hub
>>>       - Endpoint 1 In Interrupt MaxPacket 8 Interval 255ms
>>>
>>> I have the following definitions in the code:
>>>
>>> #define CONFIG_USB_OMAP3
>>> #define CONFIG_USB_EHCI
>>> #define CONFIG_USB_EHCI_OMAP
>>> #define CONFIG_SYS_USB_EHCI_MAX_ROOT_PORTS    3
>>> #define CONFIG_OMAP_EHCI_PHY1_RESET_GPIO    24
>>> #define CONFIG_USB_ULPI
>>> #define CONFIG_USB_ULPI_VIEWPORT_OMAP
>>> #define CONFIG_USB_STORAGE
>>>
>>> static struct omap_usbhs_board_data usbhs_bdata = {
>>>
>>>      .port_mode[0] = OMAP_EHCI_PORT_MODE_PHY,
>>>      .port_mode[1] = OMAP_USBHS_PORT_MODE_UNUSED,
>>>      .port_mode[2] = OMAP_USBHS_PORT_MODE_UNUSED
>>>
>>> };
>>>
>>> MUX_VAL(CP(ETK_D15_ES2),    (IDIS | PTD | DIS | M4)) /*GPIO_24*/
>>>
>>> I'd appreciate any help in fixing the problem.
>>>
>>> Thanks.
>>>
>>> Felix Radensky.
>>> _______________________________________________
>>> U-Boot mailing list
>>> U-Boot at lists.denx.de
>>> http://lists.denx.de/mailman/listinfo/u-boot

Felix.


More information about the U-Boot mailing list