[U-Boot] [PATCH v2 01/13] mx31: Move EHCI definitions to ehci-fsl.h

Stefano Babic sbabic at denx.de
Sat Nov 10 08:42:24 CET 2012


On 08/11/2012 21:27, Benoît Thébaudeau wrote:
> The EHCI definitions in i.MX31's imx-regs.h are MXC-generic, so move them to
> ehci-fsl.h so that all MXC SoCs can use them.
> 
> Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau at advansee.com>
> Cc: Marek Vasut <marex at denx.de>
> Cc: Stefano Babic <sbabic at denx.de>
> ---

Hi Benoît,

> Changes for v2: None.
> 
>  .../arch/arm/include/asm/arch-mx31/imx-regs.h      |   26 --------------------
>  .../include/usb/ehci-fsl.h                         |   22 +++++++++++++++++
>  2 files changed, 22 insertions(+), 26 deletions(-)
> 

By applying this patchset I see several minor issues reported by checkpatch:

WARNING: line over 80 characters
#303: FILE: drivers/usb/host/ehci-mx5.c:43:
+#define MXC_OTG_UCTRL_OWIE_BIT		(1 << 27)	/* OTG wakeup intr enable */

WARNING: line over 80 characters
#305: FILE: drivers/usb/host/ehci-mx5.c:45:
+#define MXC_H1_UCTRL_H1UIE_BIT		(1 << 12)	/* Host1 ULPI interrupt enable */

WARNING: line over 80 characters
#306: FILE: drivers/usb/host/ehci-mx5.c:46:
+#define MXC_H1_UCTRL_H1WIE_BIT		(1 << 11)	/* HOST1 wakeup intr enable */

WARNING: line over 80 characters
#312: FILE: drivers/usb/host/ehci-mx5.c:50:
+#define MXC_OTG_PHYCTRL_OC_DIS_BIT	(1 << 8)	/* OTG Disable Overcurrent
Event */

WARNING: line over 80 characters
#313: FILE: drivers/usb/host/ehci-mx5.c:51:
+#define MXC_H1_OC_DIS_BIT		(1 << 5)	/* UH1 Disable Overcurrent Event */

WARNING: line over 80 characters
#343: FILE: drivers/usb/host/ehci-mx5.c:174:
+			v &= ~MXC_H1_UCTRL_H1PM_BIT; /* HOST1 power mask unused */

WARNING: line over 80 characters
#352: FILE: drivers/usb/host/ehci-mx5.c:190:
+			v &= ~MXC_H2_UCTRL_H2PM_BIT; /* HOST2 power mask unused */

WARNING: line over 80 characters
#641: FILE: drivers/usb/host/ehci-mx5.c:47:
+#define MXC_OTG_UCTRL_O_PWR_POL_BIT	(1 << 24)	/* OTG power pin polarity */

WARNING: line over 80 characters
#645: FILE: drivers/usb/host/ehci-mx5.c:51:
+#define MXC_H1_UCTRL_H1_PWR_POL_BIT	(1 << 8)	/* HOST1 power pin polarity */

WARNING: line over 80 characters
#648: FILE: drivers/usb/host/ehci-mx5.c:54:
+#define MXC_OTG_PHYCTRL_OC_POL_BIT	(1 << 9)	/* OTG Polarity of
Overcurrent */

WARNING: line over 80 characters
#650: FILE: drivers/usb/host/ehci-mx5.c:56:
+#define MXC_H1_OC_POL_BIT		(1 << 6)	/* UH1 Polarity of Overcurrent */

WARNING: line over 80 characters
#652: FILE: drivers/usb/host/ehci-mx5.c:58:
+#define MXC_OTG_PHYCTRL_PWR_POL_BIT	(1 << 3)	/* OTG Power Pin Polarity */

WARNING: line over 80 characters
#873: FILE: drivers/usb/host/ehci-mxc.c:85:
+			MX25_H1_OCPOL_BIT | MX25_H1_TLL_BIT | MX25_H1_USBTE_BIT |

WARNING: line over 80 characters
#1078: FILE: drivers/usb/host/ehci-mxc.c:184:
+			MX35_H1_OCPOL_BIT | MX35_H1_TLL_BIT | MX35_H1_USBTE_BIT |

WARNING: line over 80 characters
#1179: FILE: board/freescale/mx35pdk/mx35pdk.c:105:
+	mxc_request_iomux(MX35_PIN_USBOTG_PWR, MUX_CONFIG_SION | MUX_CONFIG_FUNC);

WARNING: line over 80 characters
#1180: FILE: board/freescale/mx35pdk/mx35pdk.c:106:
+	mxc_request_iomux(MX35_PIN_USBOTG_OC, MUX_CONFIG_SION | MUX_CONFIG_FUNC);

total: 0 errors, 16 warnings, 810 lines checked

Can you fix them ? Thanks !

Best regards,
Stefano

-- 
=====================================================================
DENX Software Engineering GmbH,     MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sbabic at denx.de
=====================================================================


More information about the U-Boot mailing list