[U-Boot] [PATCH v2 01/13] mx31: Move EHCI definitions to ehci-fsl.h
Benoît Thébaudeau
benoit.thebaudeau at advansee.com
Sat Nov 10 13:37:12 CET 2012
Hi Stefano,
On Saturday, November 10, 2012 8:42:24 AM, Stefano Babic wrote:
> On 08/11/2012 21:27, Benoît Thébaudeau wrote:
> > The EHCI definitions in i.MX31's imx-regs.h are MXC-generic, so
> > move them to
> > ehci-fsl.h so that all MXC SoCs can use them.
> >
> > Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau at advansee.com>
> > Cc: Marek Vasut <marex at denx.de>
> > Cc: Stefano Babic <sbabic at denx.de>
> > ---
>
> Hi Benoît,
>
> > Changes for v2: None.
> >
> > .../arch/arm/include/asm/arch-mx31/imx-regs.h | 26
> > --------------------
> > .../include/usb/ehci-fsl.h | 22
> > +++++++++++++++++
> > 2 files changed, 22 insertions(+), 26 deletions(-)
> >
>
> By applying this patchset I see several minor issues reported by
> checkpatch:
>
> WARNING: line over 80 characters
> #303: FILE: drivers/usb/host/ehci-mx5.c:43:
> +#define MXC_OTG_UCTRL_OWIE_BIT (1 << 27) /* OTG wakeup intr enable
> */
>
> WARNING: line over 80 characters
> #305: FILE: drivers/usb/host/ehci-mx5.c:45:
> +#define MXC_H1_UCTRL_H1UIE_BIT (1 << 12) /* Host1 ULPI interrupt
> enable */
>
> WARNING: line over 80 characters
> #306: FILE: drivers/usb/host/ehci-mx5.c:46:
> +#define MXC_H1_UCTRL_H1WIE_BIT (1 << 11) /* HOST1 wakeup intr
> enable */
>
> WARNING: line over 80 characters
> #312: FILE: drivers/usb/host/ehci-mx5.c:50:
> +#define MXC_OTG_PHYCTRL_OC_DIS_BIT (1 << 8) /* OTG Disable
> Overcurrent
> Event */
>
> WARNING: line over 80 characters
> #313: FILE: drivers/usb/host/ehci-mx5.c:51:
> +#define MXC_H1_OC_DIS_BIT (1 << 5) /* UH1 Disable Overcurrent Event
> */
>
> WARNING: line over 80 characters
> #343: FILE: drivers/usb/host/ehci-mx5.c:174:
> + v &= ~MXC_H1_UCTRL_H1PM_BIT; /* HOST1 power mask unused */
>
> WARNING: line over 80 characters
> #352: FILE: drivers/usb/host/ehci-mx5.c:190:
> + v &= ~MXC_H2_UCTRL_H2PM_BIT; /* HOST2 power mask unused */
>
> WARNING: line over 80 characters
> #641: FILE: drivers/usb/host/ehci-mx5.c:47:
> +#define MXC_OTG_UCTRL_O_PWR_POL_BIT (1 << 24) /* OTG power pin
> polarity */
>
> WARNING: line over 80 characters
> #645: FILE: drivers/usb/host/ehci-mx5.c:51:
> +#define MXC_H1_UCTRL_H1_PWR_POL_BIT (1 << 8) /* HOST1 power pin
> polarity */
>
> WARNING: line over 80 characters
> #648: FILE: drivers/usb/host/ehci-mx5.c:54:
> +#define MXC_OTG_PHYCTRL_OC_POL_BIT (1 << 9) /* OTG Polarity of
> Overcurrent */
>
> WARNING: line over 80 characters
> #650: FILE: drivers/usb/host/ehci-mx5.c:56:
> +#define MXC_H1_OC_POL_BIT (1 << 6) /* UH1 Polarity of Overcurrent
> */
>
> WARNING: line over 80 characters
> #652: FILE: drivers/usb/host/ehci-mx5.c:58:
> +#define MXC_OTG_PHYCTRL_PWR_POL_BIT (1 << 3) /* OTG Power Pin
> Polarity */
>
> WARNING: line over 80 characters
> #873: FILE: drivers/usb/host/ehci-mxc.c:85:
> + MX25_H1_OCPOL_BIT | MX25_H1_TLL_BIT | MX25_H1_USBTE_BIT |
>
> WARNING: line over 80 characters
> #1078: FILE: drivers/usb/host/ehci-mxc.c:184:
> + MX35_H1_OCPOL_BIT | MX35_H1_TLL_BIT | MX35_H1_USBTE_BIT |
>
> WARNING: line over 80 characters
> #1179: FILE: board/freescale/mx35pdk/mx35pdk.c:105:
> + mxc_request_iomux(MX35_PIN_USBOTG_PWR, MUX_CONFIG_SION |
> MUX_CONFIG_FUNC);
>
> WARNING: line over 80 characters
> #1180: FILE: board/freescale/mx35pdk/mx35pdk.c:106:
> + mxc_request_iomux(MX35_PIN_USBOTG_OC, MUX_CONFIG_SION |
> MUX_CONFIG_FUNC);
>
> total: 0 errors, 16 warnings, 810 lines checked
>
> Can you fix them ? Thanks !
OK, I'll do that. For the #define-s, do you prefer that I move the comment to
the previous line, or that I split the end of the comment to the next line?
Best regards,
Benoît
More information about the U-Boot
mailing list