[U-Boot] [PATCH V3 28/32] mx6q_4x_mt41j128.cfg: add mx6 solo/duallite support

Troy Kisky troy.kisky at boundarydevices.com
Thu Oct 4 03:47:30 CEST 2012


Signed-off-by: Troy Kisky <troy.kisky at boundarydevices.com>
---
 board/freescale/imx/ddr/mx6q_4x_mt41j128.cfg |  120 +++++++++++++++++++-------
 1 file changed, 87 insertions(+), 33 deletions(-)

diff --git a/board/freescale/imx/ddr/mx6q_4x_mt41j128.cfg b/board/freescale/imx/ddr/mx6q_4x_mt41j128.cfg
index 9e20db0..f45f93e 100644
--- a/board/freescale/imx/ddr/mx6q_4x_mt41j128.cfg
+++ b/board/freescale/imx/ddr/mx6q_4x_mt41j128.cfg
@@ -49,6 +49,15 @@ BOOT_FROM      sd
  *      Address   absolute address of the register
  *      value     value to be stored in the register
  */
+/*
+ * DDR3 settings
+ * MX6Q    ddr is limited to 1066 Mhz, currently 1056 MHz(528 MHz clock),
+ *	   memory bus width: 64 bits, x16/x32/x64
+ * MX6DL   ddr is limited to 800 MHz(400 MHz clock)
+ *	   memory bus width: 64 bits, x16/x32/x64
+ * MX6SOLO ddr is limited to 800 MHz(400 MHz clock)
+ *	   memory bus width: 32 bits, x16/x32
+ */
 WRITE_ENTRY1(IOM_DRAM_SDQS0, 0x00000030)
 WRITE_ENTRY1(IOM_DRAM_SDQS1, 0x00000030)
 WRITE_ENTRY1(IOM_DRAM_SDQS2, 0x00000030)
@@ -90,6 +99,7 @@ WRITE_ENTRY1(IOM_GRP_B6DS, 0x00000030)
 WRITE_ENTRY1(IOM_GRP_B7DS, 0x00000030)
 
 WRITE_ENTRY1(IOM_GRP_ADDDS, 0x00000030)
+
 /* (differential input) */
 WRITE_ENTRY1(IOM_DDRMODE_CTL, 0x00020000)
 /* disable ddr pullups */
@@ -119,48 +129,92 @@ WRITE_ENTRY1(MMDC_P0_MDMISC, 0x00081740)
  * MDSCR, con_req
  */
 WRITE_ENTRY1(MMDC_P0_MDSCR, 0x00008000)
+
 /*
- * MDCFG0, tRFC=0x56 clocks, tXS=0x5b clocks
- * tXP=4 clocks, tXPDLL=13 clocks
- * tFAW=24 clocks, cas=8 cycles
+ * MDCFG0,
+ * MX6Q:
+ *	tRFC=0x56 clocks, tXS=0x5b clocks, tXP=4 clocks, tXPDLL=13 clocks
+ *	tFAW=24 clocks, cas=8 cycles
+ * MX6DL/SOLO:
+ *	tRFC=0x6a clocks, tXS=0x6e clocks, tXP=3 clocks, tXPDLL=10 clocks
+ *	 tFAW=19 clocks, cas=6 cycles
  */
-WRITE_ENTRY1(MMDC_P0_MDCFG0, 0x555A7975)
+WRITE_ENTRY2(MMDC_P0_MDCFG0, 0x555A7975, 0x696D5323)
+
 /*
- * MDCFG1, tRDC=8, tRP=8, tRC=27,tRAS=20,tRPA=tRP+1,tWR=8
- * tMRD=4, tCWL=6
+ * MDCFG1,
+ * MX6Q:
+ *	tRDC=8, tRP=8, tRC=27, tRAS=20, tRPA=tRP+1, tWR=8, tMRD=4, tCWL=6
+ * MX6DL/SOLO:
+ *	tRDC=6, tRP=6, tRC=20, tRAS=15, tRPA=tRP+1, tWR=7, tMRD=4, tCWL=5
  */
-WRITE_ENTRY1(MMDC_P0_MDCFG1, 0xFF538E64)
+WRITE_ENTRY2(MMDC_P0_MDCFG1, 0xFF538E64, 0xB66E8C63)
+
 /*
  * MDCFG2,tDLLK=512,tRTP=4,tWTR=4,tRRD=4
  */
 WRITE_ENTRY1(MMDC_P0_MDCFG2, 0x01FF00DB)
 WRITE_ENTRY1(MMDC_P0_MDRWD, 0x000026D2)
-
 WRITE_ENTRY1(MMDC_P0_MDOR, 0x005B0E21)
-WRITE_ENTRY1(MMDC_P0_MDOTC, 0x09444040)
-WRITE_ENTRY1(MMDC_P0_MDPDC, 0x00025576)
 
 /*
- * Mx6Q - 64 bit wide ddr
+ * MMDC_MDOTC,
+ * MX6Q:
+ *	tAOFPD=2 cycles, tAONPD=2, tANPD=5, tAXPD=5, tODTLon=5, tODT_idle_off=5
+ * MX6DL/SOLO:
+ *	tAOFPD=1 cycles, tAONPD=1, tANPD=4, tAXPD=4, tODTLon=4, tODT_idle_off=4
+ */
+WRITE_ENTRY2(MMDC_P0_MDOTC, 0x09444040, 0x00333030)
+
+/*
+ * MDPDC - [17:16](2) => CKE pulse width = 3 cycles.
+ * [15:12](5) => PWDT_1 = 256 cycles
+ * [11:8](5) =>PWDR_0 = 256 cycles
+ * MX6Q:       [2:0](6) => CKSRE = 6 cycles, [5:3](6) => CKSRX = 6 cycles
+ * MX6DL/SOLO: [2:0](5) => CKSRE = 5 cycles, [5:3](5) => CKSRX = 5 cycles
+ */
+WRITE_ENTRY2(MMDC_P0_MDPDC, 0x00025576, 0x0002556D)
+
+/*
+ * MX6Q/DL - 64 bit wide ddr
  * last address is  (1<<28 (base) + 1<<30  - 1)  / (1<<25) =
  * 	1<<3 + 1<<5 - 1 = 8 + 0x20 -1 = 0x27
  */
+/*
+ * MX6SOLO - 32 bit wide ddr
+ * last address is  (1<<28 (base) + 1<<29  - 1)  / (1<<25) =
+ *	1<<3 + 1<<4 - 1 = 8 + 0x10 -1 = 0x17
+ */
 /* MDASP, CS0_END */
-WRITE_ENTRY1(MMDC_P0_MDASP, 0x00000027)
+WRITE_ENTRY3(MMDC_P0_MDASP, 0x00000027, 0x00000027, 0x00000017)
 /*
- * MDCTL, CS0 enable, CS1 disabled, row=14, col=10, burst=8, width=64/32bit
- * mx6q   : row+col+bank+width=14+10+3+3=30 = 1G
+ * MDCTL, CS0 enable, CS1 disabled, row=14, col=10, burst=8
+ * MX6Q/DL: width=64bit row+col+bank+width=14+10+3+3=30 = 1G
+ * MX6SOLO: width=32bit row+col+bank+width=14+10+3+2=29 = 512M
  */
-WRITE_ENTRY1(MMDC_P0_MDCTL, 0x831A0000)
+WRITE_ENTRY3(MMDC_P0_MDCTL, 0x831A0000, 0x831A0000, 0x83190000)
 
-/* MDSCR, con_req, LOAD MR2, CS0, A3,A10 set (CAS Write=6), RZQ/2 */
-WRITE_ENTRY1(MMDC_P0_MDSCR, 0x04088032)
+/*
+ * LOAD MR2: MDSCR, con_req,  CS0, A10 set - RZQ/2
+ * MX6Q:    A3 set(CAS Write=6)
+ * MX6DL/SOLO: (CAS Write=5)
+ */
+WRITE_ENTRY2(MMDC_P0_MDSCR, 0x04088032, 0x04008032)
 /* LOAD MR3, CS0 */
 WRITE_ENTRY1(MMDC_P0_MDSCR, 0x00008033)
-/* LOAD MR1, CS0, A1,A6 set Rtt=RZQ/2, ODI=RZQ/7 */
-WRITE_ENTRY1(MMDC_P0_MDSCR, 0x00428031)
-/* LOAD MR0, CS0, A6,A8,A11 set CAS=8, WR=8, DLL reset */
-WRITE_ENTRY1(MMDC_P0_MDSCR, 0x09408030)
+
+/*
+ * LOAD MR1, CS0
+ * MX6Q: A6 set: Rtt=RZQ/2, A1 set: ODI=RZQ/7
+ * MX6DL/SOLO: A2 set: Rtt=RZQ/4, ODI=RZQ/6
+ */
+WRITE_ENTRY2(MMDC_P0_MDSCR, 0x00428031, 0x00048031)
+
+/* LOAD MR0, CS0 A8 set: DLL Reset
+ * MX6Q: A6 set: CAS=8 A11 set: WR=8
+ * MX6DL/SOLO: A4 set: CAS=5, A9,A10 set: WR=7
+ */
+WRITE_ENTRY2(MMDC_P0_MDSCR, 0x09408030, 0x07208030)
 
 /* ZQ calibrate, CS0 */
 WRITE_ENTRY1(MMDC_P0_MDSCR, 0x04008040)
@@ -173,18 +227,18 @@ WRITE_ENTRY1(MMDC_P0_MPODTCTRL, 0x00022227)
 WRITE_ENTRY1(MMDC_P1_MPODTCTRL, 0x00022227)
 
 /* MPDGCTRL0/1 DQS GATE*/
-WRITE_ENTRY1(MMDC_P0_MPDGCTRL0, 0x434B0350)
-WRITE_ENTRY1(MMDC_P0_MPDGCTRL1, 0x034C0359)
-WRITE_ENTRY1(MMDC_P1_MPDGCTRL0, 0x434B0350)
-WRITE_ENTRY1(MMDC_P1_MPDGCTRL1, 0x03650348)
-WRITE_ENTRY1(MMDC_P0_MPRDDLCTL, 0x4436383B)
-WRITE_ENTRY1(MMDC_P1_MPRDDLCTL, 0x39393341)
-WRITE_ENTRY1(MMDC_P0_MPWRDLCTL, 0x35373933)
-WRITE_ENTRY1(MMDC_P1_MPWRDLCTL, 0x48254A36)
-WRITE_ENTRY1(MMDC_P0_MPWLDECTRL0, 0x001F001F)
-WRITE_ENTRY1(MMDC_P0_MPWLDECTRL1, 0x001F001F)
-WRITE_ENTRY1(MMDC_P1_MPWLDECTRL0, 0x00440044)
-WRITE_ENTRY1(MMDC_P1_MPWLDECTRL1, 0x00440044)
+WRITE_ENTRY2(MMDC_P0_MPDGCTRL0, 0x434B0350, 0x42350231)
+WRITE_ENTRY2(MMDC_P0_MPDGCTRL1, 0x034C0359, 0x021A0218)
+WRITE_ENTRY2(MMDC_P1_MPDGCTRL0, 0x434B0350, 0x42350231)
+WRITE_ENTRY2(MMDC_P1_MPDGCTRL1, 0x03650348, 0x021A0218)
+WRITE_ENTRY2(MMDC_P0_MPRDDLCTL, 0x4436383B, 0x4B4B4E49)
+WRITE_ENTRY2(MMDC_P1_MPRDDLCTL, 0x39393341, 0x4B4B4E49)
+WRITE_ENTRY2(MMDC_P0_MPWRDLCTL, 0x35373933, 0x3F3F3035)
+WRITE_ENTRY2(MMDC_P1_MPWRDLCTL, 0x48254A36, 0x3F3F3035)
+WRITE_ENTRY2(MMDC_P0_MPWLDECTRL0, 0x001F001F, 0x0040003C)
+WRITE_ENTRY2(MMDC_P0_MPWLDECTRL1, 0x001F001F, 0x0032003E)
+WRITE_ENTRY2(MMDC_P1_MPWLDECTRL0, 0x00440044, 0x0040003C)
+WRITE_ENTRY2(MMDC_P1_MPWLDECTRL1, 0x00440044, 0x0032003E)
 
 /* MPMUR0 - Complete calibration by forced measurement */
 WRITE_ENTRY1(MMDC_P0_MPMUR0, 0x00000800)
-- 
1.7.9.5



More information about the U-Boot mailing list