[U-Boot] [PATCH V4] i.MX6: mx6qsabrelite: Add splash screen support

Eric Nelson eric.nelson at boundarydevices.com
Sat Sep 22 00:53:50 CEST 2012


Adds support for two LVDS panels and one RGB panel to the SABRE-Lite
board:
     Hannstar-XGA	- 1024 x 768 LVDS (Freescale part number MCIMX-LVDS1)
     wsvga-lvds		- 1024 x 600 LVDS (Boundary p/n Nit6X_1024x600)
     wvga-rgb		- 800 x 480 RGB (Boundary p/n Nit6X_800x480)

Auto-detects panel by probing the I2C touch controller of each.

Setting 'panel' environment variable to one of the names above will override
auto-detection.

Signed-off-by: Eric Nelson <eric.nelson at boundarydevices.com>
---
 board/freescale/mx6qsabrelite/mx6qsabrelite.c |  245 ++++++++++++++++++++++++-
 drivers/video/ipu_common.c                    |    2 +-
 include/configs/mx6qsabrelite.h               |   15 ++-
 3 files changed, 259 insertions(+), 3 deletions(-)

diff --git a/board/freescale/mx6qsabrelite/mx6qsabrelite.c b/board/freescale/mx6qsabrelite/mx6qsabrelite.c
index 4b4e89b..d274d8c 100644
--- a/board/freescale/mx6qsabrelite/mx6qsabrelite.c
+++ b/board/freescale/mx6qsabrelite/mx6qsabrelite.c
@@ -36,6 +36,11 @@
 #include <micrel.h>
 #include <miiphy.h>
 #include <netdev.h>
+#include <linux/fb.h>
+#include <ipu_pixfmt.h>
+#include <asm/arch/crm_regs.h>
+#include <i2c.h>
+
 DECLARE_GLOBAL_DATA_PTR;
 
 #define UART_PAD_CTRL  (PAD_CTL_PKE | PAD_CTL_PUE |	       \
@@ -372,14 +377,252 @@ int setup_sata(void)
 }
 #endif
 
+#if defined(CONFIG_VIDEO_IPUV3)
+static struct fb_videomode videomodes[] = {{
+		.name           = "Hannstar-XGA",
+		.refresh        = 60,
+		.xres           = 1024,
+		.yres           = 768,
+		.pixclock       = 15385,
+		.left_margin    = 220,
+		.right_margin   = 40,
+		.upper_margin   = 21,
+		.lower_margin   = 7,
+		.hsync_len      = 60,
+		.vsync_len      = 10,
+		.sync           = FB_SYNC_EXT, /* a.k.a. LVDS */
+		.vmode          = FB_VMODE_NONINTERLACED
+	}, {
+		.name           = "wsvga-lvds",
+		.refresh        = 60,
+		.xres           = 1024,
+		.yres           = 600,
+		.pixclock       = 15385,
+		.left_margin    = 220,
+		.right_margin   = 40,
+		.upper_margin   = 21,
+		.lower_margin   = 7,
+		.hsync_len      = 60,
+		.vsync_len      = 10,
+		.sync           = FB_SYNC_EXT, /* a.k.a. LVDS */
+		.vmode          = FB_VMODE_NONINTERLACED
+	}, {
+		.name           = "wvga-rgb",
+		.refresh        = 57,
+		.xres           = 800,
+		.yres           = 480,
+		.pixclock       = 37037,
+		.left_margin    = 40,
+		.right_margin   = 60,
+		.upper_margin   = 10,
+		.lower_margin   = 10,
+		.hsync_len      = 20,
+		.vsync_len      = 10,
+		.sync           = 0,
+		.vmode          = FB_VMODE_NONINTERLACED
+} };
+
+#define IS_LVDS(m) (FB_SYNC_EXT & (m).sync)
+
+struct i2c_display {
+	int bus;
+	int addr;
+	char const *name;
+};
+
+static struct i2c_display const i2c_displays[] = {
+{
+	.bus		= 2,
+	.addr		= 0x4,
+	.name           = "Hannstar-XGA",
+}, {
+	.bus		= 2,
+	.addr		= 0x38,
+	.name           = "wsvga-lvds",
+}, {
+	.bus		= 2,
+	.addr		= 0x48,
+	.name           = "wvga-rgb",
+} };
+
+static iomux_v3_cfg_t rgb_pads[] = {
+	MX6Q_PAD_DI0_DISP_CLK__IPU1_DI0_DISP_CLK,
+	MX6Q_PAD_DI0_PIN15__IPU1_DI0_PIN15,
+	MX6Q_PAD_DI0_PIN2__IPU1_DI0_PIN2,
+	MX6Q_PAD_DI0_PIN3__IPU1_DI0_PIN3,
+	MX6Q_PAD_DI0_PIN4__GPIO_4_20,
+	MX6Q_PAD_DISP0_DAT0__IPU1_DISP0_DAT_0,
+	MX6Q_PAD_DISP0_DAT1__IPU1_DISP0_DAT_1,
+	MX6Q_PAD_DISP0_DAT2__IPU1_DISP0_DAT_2,
+	MX6Q_PAD_DISP0_DAT3__IPU1_DISP0_DAT_3,
+	MX6Q_PAD_DISP0_DAT4__IPU1_DISP0_DAT_4,
+	MX6Q_PAD_DISP0_DAT5__IPU1_DISP0_DAT_5,
+	MX6Q_PAD_DISP0_DAT6__IPU1_DISP0_DAT_6,
+	MX6Q_PAD_DISP0_DAT7__IPU1_DISP0_DAT_7,
+	MX6Q_PAD_DISP0_DAT8__IPU1_DISP0_DAT_8,
+	MX6Q_PAD_DISP0_DAT9__IPU1_DISP0_DAT_9,
+	MX6Q_PAD_DISP0_DAT10__IPU1_DISP0_DAT_10,
+	MX6Q_PAD_DISP0_DAT11__IPU1_DISP0_DAT_11,
+	MX6Q_PAD_DISP0_DAT12__IPU1_DISP0_DAT_12,
+	MX6Q_PAD_DISP0_DAT13__IPU1_DISP0_DAT_13,
+	MX6Q_PAD_DISP0_DAT14__IPU1_DISP0_DAT_14,
+	MX6Q_PAD_DISP0_DAT15__IPU1_DISP0_DAT_15,
+	MX6Q_PAD_DISP0_DAT16__IPU1_DISP0_DAT_16,
+	MX6Q_PAD_DISP0_DAT17__IPU1_DISP0_DAT_17,
+	MX6Q_PAD_DISP0_DAT18__IPU1_DISP0_DAT_18,
+	MX6Q_PAD_DISP0_DAT19__IPU1_DISP0_DAT_19,
+	MX6Q_PAD_DISP0_DAT20__IPU1_DISP0_DAT_20,
+	MX6Q_PAD_DISP0_DAT21__IPU1_DISP0_DAT_21,
+	MX6Q_PAD_DISP0_DAT22__IPU1_DISP0_DAT_22,
+	MX6Q_PAD_DISP0_DAT23__IPU1_DISP0_DAT_23,
+};
+
+static iomux_v3_cfg_t backlight_pads[] = {
+	/* Backlight on RGB connector: J15 */
+	MX6Q_PAD_SD1_DAT3__GPIO_1_21 | MUX_PAD_CTRL(NO_PAD_CTRL),
+#define RGB_BACKLIGHT_GP IMX_GPIO_NR(1, 21)
+
+	/* Backlight on LVDS connector: J6 */
+	MX6Q_PAD_SD1_CMD__GPIO_1_18 | MUX_PAD_CTRL(NO_PAD_CTRL),
+#define LVDS_BACKLIGHT_GP IMX_GPIO_NR(1, 18)
+};
+
+int board_video_skip(void)
+{
+	int i;
+	int ret;
+	char const *panel = getenv("panel");
+	if (!panel) {
+		for (i = 0; i < ARRAY_SIZE(i2c_displays); i++) {
+			struct i2c_display const *dev = i2c_displays+i;
+			if ((0 == i2c_set_bus_num(dev->bus))
+			     &&
+			    (0 == i2c_probe(dev->addr))) {
+				panel = dev->name;
+				printf("auto-detected panel %s\n", panel);
+				break;
+			}
+		}
+		if (!panel) {
+			panel = videomodes[0].name;
+			printf("No panel detected: default to %s\n", panel);
+		}
+	}
+	for (i = 0; i < ARRAY_SIZE(videomodes); i++) {
+		if (!strcmp(panel, videomodes[i].name))
+			break;
+	}
+	if (i < ARRAY_SIZE(videomodes)) {
+		ret = ipuv3_fb_init(videomodes+i, 0, IPU_PIX_FMT_RGB666);
+		if (!ret) {
+			if (IS_LVDS(videomodes[i]))
+				gpio_direction_output(LVDS_BACKLIGHT_GP, 1);
+			else {
+				imx_iomux_v3_setup_multiple_pads(
+					rgb_pads,
+					 ARRAY_SIZE(rgb_pads));
+				gpio_direction_output(RGB_BACKLIGHT_GP, 1);
+			}
+			printf("Display: %s (%ux%u)\n",
+			       videomodes[i].name,
+			       videomodes[i].xres,
+			       videomodes[i].yres);
+		} else
+			printf("LCD %s cannot be configured: %d\n",
+			       videomodes[i].name, ret);
+	} else {
+		printf("unsupported panel %s\n", panel);
+		ret = -EINVAL;
+	}
+	return (0 != ret);
+}
+
+void lcd_iomux(void)
+{
+	struct mxc_ccm_reg *mxc_ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR;
+	struct anatop_regs *anatop = (struct anatop_regs *)ANATOP_BASE_ADDR;
+	struct iomuxc *iomux = (struct iomuxc *)IOMUXC_BASE_ADDR;
+
+	int reg;
+
+	/* Turn on LDB0,IPU,IPU DI0 clocks */
+	reg = __raw_readl(&mxc_ccm->CCGR3);
+	reg |=   MXC_CCM_CCGR3_IPU1_IPU_DI0_OFFSET
+		|MXC_CCM_CCGR3_LDB_DI0_MASK;
+	writel(reg, &mxc_ccm->CCGR3);
+
+	/* set PFD1_FRAC to 0x13 == 455 MHz (480*18)/0x13 */
+	writel(ANATOP_PFD_480_PFD1_FRAC_MASK, &anatop->pfd_480_clr);
+	writel(0x13<<ANATOP_PFD_480_PFD1_FRAC_SHIFT, &anatop->pfd_480_set);
+
+	/* set LDB0, LDB1 clk select to 011/011 */
+	reg = readl(&mxc_ccm->cs2cdr);
+	reg &= ~(MXC_CCM_CS2CDR_LDB_DI0_CLK_SEL_MASK
+		 |MXC_CCM_CS2CDR_LDB_DI1_CLK_SEL_MASK);
+	reg |= (3<<MXC_CCM_CS2CDR_LDB_DI0_CLK_SEL_OFFSET)
+	      |(3<<MXC_CCM_CS2CDR_LDB_DI1_CLK_SEL_OFFSET);
+	writel(reg, &mxc_ccm->cs2cdr);
+
+	reg = readl(&mxc_ccm->cscmr2);
+	reg |= MXC_CCM_CSCMR2_LDB_DI0_IPU_DIV;
+	writel(reg, &mxc_ccm->cscmr2);
+
+	reg = readl(&mxc_ccm->chsccdr);
+	reg &= ~(MXC_CCM_CHSCCDR_IPU1_DI0_PRE_CLK_SEL_MASK
+		|MXC_CCM_CHSCCDR_IPU1_DI0_PODF_MASK
+		|MXC_CCM_CHSCCDR_IPU1_DI0_CLK_SEL_MASK);
+	reg |= (CHSCCDR_CLK_SEL_LDB_DI0
+		<<MXC_CCM_CHSCCDR_IPU1_DI0_CLK_SEL_OFFSET)
+	      |(CHSCCDR_PODF_DIVIDE_BY_3
+		<<MXC_CCM_CHSCCDR_IPU1_DI0_PODF_OFFSET)
+	      |(CHSCCDR_IPU_PRE_CLK_540M_PFD
+		<<MXC_CCM_CHSCCDR_IPU1_DI0_PRE_CLK_SEL_OFFSET);
+	writel(reg, &mxc_ccm->chsccdr);
+
+	reg = IOMUXC_GPR2_BGREF_RRMODE_EXTERNAL_RES
+	     |IOMUXC_GPR2_DI1_VS_POLARITY_ACTIVE_HIGH
+	     |IOMUXC_GPR2_DI0_VS_POLARITY_ACTIVE_LOW
+	     |IOMUXC_GPR2_BIT_MAPPING_CH1_SPWG
+	     |IOMUXC_GPR2_DATA_WIDTH_CH1_18BIT
+	     |IOMUXC_GPR2_BIT_MAPPING_CH0_SPWG
+	     |IOMUXC_GPR2_DATA_WIDTH_CH0_18BIT
+	     |IOMUXC_GPR2_LVDS_CH1_MODE_DISABLED
+	     |IOMUXC_GPR2_LVDS_CH0_MODE_ENABLED_DI0;
+	writel(reg, &iomux->gpr[2]);
+
+	reg = readl(&iomux->gpr[3]);
+	reg = (reg & ~IOMUXC_GPR3_LVDS0_MUX_CTL_MASK)
+	    | (IOMUXC_GPR3_MUX_SRC_IPU1_DI0
+	       <<IOMUXC_GPR3_LVDS0_MUX_CTL_OFFSET);
+	writel(reg, &iomux->gpr[3]);
+
+	/* backlights off until needed */
+	imx_iomux_v3_setup_multiple_pads(backlight_pads,
+					 ARRAY_SIZE(backlight_pads));
+	gpio_direction_input(LVDS_BACKLIGHT_GP);
+	gpio_direction_input(RGB_BACKLIGHT_GP);
+}
+#endif
+
 int board_early_init_f(void)
 {
 	setup_iomux_uart();
 	setup_buttons();
-
+#if defined(CONFIG_VIDEO_IPUV3)
+	lcd_iomux();
+#endif
 	return 0;
 }
 
+/*
+ * Do not overwrite the console
+ * Use always serial for U-Boot console
+ */
+int overwrite_console(void)
+{
+	return 1;
+}
+
 int board_init(void)
 {
        /* address of boot parameters */
diff --git a/drivers/video/ipu_common.c b/drivers/video/ipu_common.c
index cc8f881..5f0a1a8 100644
--- a/drivers/video/ipu_common.c
+++ b/drivers/video/ipu_common.c
@@ -218,7 +218,7 @@ static struct clk ipu_clk = {
 #else
 	.enable_reg = (u32 *)(CCM_BASE_ADDR +
 		offsetof(struct mxc_ccm_reg, CCGR3)),
-	.enable_shift = MXC_CCM_CCGR3_IPU1_IPU_DI0_OFFSET,
+	.enable_shift = MXC_CCM_CCGR3_IPU1_IPU_MASK,
 #endif
 	.enable = clk_ipu_enable,
 	.disable = clk_ipu_disable,
diff --git a/include/configs/mx6qsabrelite.h b/include/configs/mx6qsabrelite.h
index 72d0154..d0c3e0a 100644
--- a/include/configs/mx6qsabrelite.h
+++ b/include/configs/mx6qsabrelite.h
@@ -39,7 +39,7 @@
 #define CONFIG_REVISION_TAG
 
 /* Size of malloc() pool */
-#define CONFIG_SYS_MALLOC_LEN	       (CONFIG_ENV_SIZE + 2 * 1024 * 1024)
+#define CONFIG_SYS_MALLOC_LEN         (10 * 1024 * 1024)
 
 #define CONFIG_BOARD_EARLY_INIT_F
 #define CONFIG_MISC_INIT_R
@@ -121,6 +121,19 @@
 /* Miscellaneous commands */
 #define CONFIG_CMD_BMODE
 
+/* Framebuffer and LCD */
+#define CONFIG_VIDEO
+#define CONFIG_VIDEO_IPUV3
+#define CONFIG_CFB_CONSOLE
+#define CONFIG_VGA_AS_SINGLE_DEVICE
+#define CONFIG_SYS_CONSOLE_IS_IN_ENV
+#define CONFIG_SYS_CONSOLE_OVERWRITE_ROUTINE
+#define CONFIG_VIDEO_BMP_RLE8
+#define CONFIG_SPLASH_SCREEN
+#define CONFIG_BMP_16BPP
+#define CONFIG_VIDEO_LOGO
+#define CONFIG_IPUV3_CLK 260000000
+
 /* allow to overwrite serial and ethaddr */
 #define CONFIG_ENV_OVERWRITE
 #define CONFIG_CONS_INDEX	       1
-- 
1.7.9



More information about the U-Boot mailing list