[U-Boot] [PATCH v2 2/2] add Eukrea's CPUIMX25

Eric Bénard eric at eukrea.com
Sun Sep 23 14:03:06 CEST 2012


this board is based on an i.MX25 from Freescale.
It consists of a SOM containing :
- NAND flash (internal or external boot supported and tested)
- mDDR (64MB tested)
- ethernet PHY connected in RMII mode (tested)
and a baseboard containing :
- a serial transceiver on UART1 (tested)
- a SDCard connector on eSDHC1 (tested but disabled until Benoît's fix
  gets applied)

bootlog :
U-Boot 2012.10-rc1-00003-gdd12be5 (Sep 23 2012 - 13:53:21)

CPU:   Freescale i.MX25 rev1.2 at 399 MHz
Reset cause: POR

DRAM:  64 MiB
NAND:  256 MiB
MMC:
In:    serial
Out:   serial
Err:   serial
Net:   FEC
Hit any key to stop autoboot:  0

Signed-off-by: Eric Bénard <eric at eukrea.com>
---
v2: rebased against 2012.10-rc1, disabled eSDHC until proper fix
    from Benoît gets applied, updated bootlog.

 MAINTAINERS                               |    2 +
 board/eukrea/cpuimx25/Makefile            |   44 +++++++
 board/eukrea/cpuimx25/config.mk           |    5 +
 board/eukrea/cpuimx25/cpuimx25.c          |  123 ++++++++++++++++++
 board/eukrea/cpuimx25/imximage.cfg        |   55 ++++++++
 board/eukrea/cpuimx25/lowlevel_init.S     |  113 ++++++++++++++++
 boards.cfg                                |    2 +
 include/configs/cpuimx25.h                |  198 +++++++++++++++++++++++++++++
 nand_spl/board/eukrea/cpuimx25/Makefile   |   79 ++++++++++++
 nand_spl/board/eukrea/cpuimx25/config.mk  |    1 +
 nand_spl/board/eukrea/cpuimx25/u-boot.lds |   83 ++++++++++++
 11 files changed, 705 insertions(+), 0 deletions(-)
 create mode 100644 board/eukrea/cpuimx25/Makefile
 create mode 100644 board/eukrea/cpuimx25/config.mk
 create mode 100644 board/eukrea/cpuimx25/cpuimx25.c
 create mode 100644 board/eukrea/cpuimx25/imximage.cfg
 create mode 100644 board/eukrea/cpuimx25/lowlevel_init.S
 create mode 100644 include/configs/cpuimx25.h
 create mode 100644 nand_spl/board/eukrea/cpuimx25/Makefile
 create mode 100644 nand_spl/board/eukrea/cpuimx25/config.mk
 create mode 100644 nand_spl/board/eukrea/cpuimx25/u-boot.lds

diff --git a/MAINTAINERS b/MAINTAINERS
index aa54fe1..94e759f 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -606,6 +606,8 @@ Eric Benard <eric at eukrea.com>
 	cpuat91		ARM920T
 	cpu9260		ARM926EJS (AT91SAM9260 SoC)
 	cpu9G20		ARM926EJS (AT91SAM9G20 SoC)
+	cpuimx25	i.MX25
+	cpuimx25nand	i.MX25
 
 Ajay Bhargav <ajay.bhargav at einfochips.com>
 
diff --git a/board/eukrea/cpuimx25/Makefile b/board/eukrea/cpuimx25/Makefile
new file mode 100644
index 0000000..46131fd
--- /dev/null
+++ b/board/eukrea/cpuimx25/Makefile
@@ -0,0 +1,44 @@
+#
+# (C) Copyright 2009 DENX Software Engineering
+# Author: John Rigby <jcrigby at gmail.com>
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+include $(TOPDIR)/config.mk
+
+LIB	= $(obj)lib$(BOARD).o
+
+COBJS	:= cpuimx25.o
+SOBJS	:= lowlevel_init.o
+
+SRCS	:= $(SOBJS:.o=.S) $(COBJS:.o=.c)
+OBJS	:= $(addprefix $(obj),$(COBJS))
+SOBJS	:= $(addprefix $(obj),$(SOBJS))
+
+$(LIB):	$(obj).depend $(OBJS) $(SOBJS)
+	$(call cmd_link_o_target, $(OBJS) $(SOBJS))
+
+#########################################################################
+
+include $(SRCTREE)/rules.mk
+
+sinclude $(obj).depend
+
+#########################################################################
diff --git a/board/eukrea/cpuimx25/config.mk b/board/eukrea/cpuimx25/config.mk
new file mode 100644
index 0000000..18b2883
--- /dev/null
+++ b/board/eukrea/cpuimx25/config.mk
@@ -0,0 +1,5 @@
+ifdef CONFIG_NAND_SPL
+CONFIG_SYS_TEXT_BASE = 0x810c0000
+else
+CONFIG_SYS_TEXT_BASE = 0x81200000
+endif
diff --git a/board/eukrea/cpuimx25/cpuimx25.c b/board/eukrea/cpuimx25/cpuimx25.c
new file mode 100644
index 0000000..72fa8a5
--- /dev/null
+++ b/board/eukrea/cpuimx25/cpuimx25.c
@@ -0,0 +1,123 @@
+/*
+ * (C) Copyright 2009 DENX Software Engineering
+ * (C) Copyright 2012 Eukrea Electromatique <www.eukrea.com>
+ * Eric Benard <eric at eukrea.com>
+ *
+ * Based on tx25.c:
+ *   Author: John Rigby <jrigby at gmail.com>
+ *
+ * Based on imx27lite.c:
+ *   Copyright (C) 2008,2009 Eric Jarrige <jorasse at users.sourceforge.net>
+ *   Copyright (C) 2009 Ilya Yanok <yanok at emcraft.com>
+ * And:
+ *   RedBoot tx25_misc.c Copyright (C) 2009 Red Hat
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ *
+ */
+#include <common.h>
+#include <asm/io.h>
+#include <asm/arch/imx-regs.h>
+#include <asm/arch/imx25-pinmux.h>
+#include <asm/gpio.h>
+#include <asm/arch/sys_proto.h>
+#include <mmc.h>
+#include <fsl_esdhc.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+#ifdef CONFIG_FSL_ESDHC
+struct fsl_esdhc_cfg esdhc_cfg[1] = {
+	{IMX_MMC_SDHC1_BASE},
+};
+#endif
+
+int board_init()
+{
+#ifdef CONFIG_MXC_UART
+	mx25_uart1_init_pins();
+#endif
+	/* board id for linux */
+	gd->bd->bi_boot_params = PHYS_SDRAM_1 + 0x100;
+	return 0;
+}
+
+int board_late_init(void)
+{
+#ifdef CONFIG_FEC_MXC
+	mx25_fec_init_pins();
+#endif
+	return 0;
+}
+
+int dram_init(void)
+{
+	/* dram_init must store complete ramsize in gd->ram_size */
+	gd->ram_size = get_ram_size((void *)PHYS_SDRAM_1,
+				PHYS_SDRAM_1_SIZE);
+	return 0;
+}
+
+void dram_init_banksize(void)
+{
+	gd->bd->bi_dram[0].start = PHYS_SDRAM_1;
+	gd->bd->bi_dram[0].size = get_ram_size((void *)PHYS_SDRAM_1,
+			PHYS_SDRAM_1_SIZE);
+}
+
+int checkboard(void)
+{
+	printf("Eukrea Electromatique CPUIMX25\n");
+	return 0;
+}
+
+#ifdef CONFIG_FSL_ESDHC
+int board_mmc_getcd(struct mmc *mmc)
+{
+	struct iomuxc_mux_ctl *muxctl;
+	struct iomuxc_pad_ctl *padctl;
+	struct gpio_regs *gpio2 = (struct gpio_regs *)IMX_GPIO2_BASE;
+	u32 val;
+
+	muxctl = (struct iomuxc_mux_ctl *)IMX_IOPADMUX_BASE;
+	padctl = (struct iomuxc_pad_ctl *)IMX_IOPADCTL_BASE;
+
+	writel(MX25_PIN_MUX_MODE(5), &muxctl->pad_de_b);
+
+	writel(0x0, &padctl->pad_de_b);
+
+	val = readl(&gpio2->gpio_dir) & ~(1 << 20);
+	writel(val, &gpio2->gpio_dir);
+	val = readl(&gpio2->gpio_dr) & (1 << 20);
+	return val ? 0 : 1;
+
+}
+
+int board_mmc_init(bd_t *bis)
+{
+	struct iomuxc_mux_ctl *muxctl;
+	struct iomuxc_pad_ctl *padctl;
+	u32 sdhc1_mux_mode = MX25_PIN_MUX_MODE(0) | MX25_PIN_MUX_SION;
+	muxctl = (struct iomuxc_mux_ctl *)IMX_IOPADMUX_BASE;
+	writel(sdhc1_mux_mode, &muxctl->pad_sd1_cmd);
+	writel(sdhc1_mux_mode, &muxctl->pad_sd1_clk);
+	writel(sdhc1_mux_mode, &muxctl->pad_sd1_data0);
+	writel(sdhc1_mux_mode, &muxctl->pad_sd1_data1);
+	writel(sdhc1_mux_mode, &muxctl->pad_sd1_data2);
+	writel(sdhc1_mux_mode, &muxctl->pad_sd1_data3);
+	return fsl_esdhc_initialize(bis, &esdhc_cfg[0]);
+}
+#endif
diff --git a/board/eukrea/cpuimx25/imximage.cfg b/board/eukrea/cpuimx25/imximage.cfg
new file mode 100644
index 0000000..c0b7b20
--- /dev/null
+++ b/board/eukrea/cpuimx25/imximage.cfg
@@ -0,0 +1,55 @@
+#
+# (C) Copyright 2009
+# Stefano Babic DENX Software Engineering sbabic at denx.de.
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+# GNU General Public License for more details.
+#
+# Refer docs/README.imxmage for more details about how-to configure
+# and create imximage boot image
+#
+# The syntax is taken as close as possible with the kwbimage
+
+# Boot Device : one of
+# nand, sd, spi
+
+BOOT_FROM	nand
+
+# Device Configuration Data (DCD)
+#
+# Each entry must have the format:
+# Addr-type           Address        Value
+#
+# where:
+#	Addr-type register length (1,2 or 4 bytes)
+#	Address	  absolute address of the register
+#	value	  value to be stored in the register
+
+# MDDR init
+DATA 4 0xb8001010 0x00000004
+DATA 4 0xb8001000 0x92100000
+DATA 1 0x80000400 0x12344321
+DATA 4 0xb8001000 0xa2100000
+DATA 4 0x80000000 0x12344321
+DATA 4 0x80000000 0x12344321
+DATA 4 0xb8001000 0xb2100000
+DATA 1 0x80000033 0xda
+DATA 1 0x81000000 0xff
+DATA 4 0xb8001000 0x82216080
+DATA 4 0xb8001004 0x00295729
+DATA 4 0x53f80008 0x20034000
+
+# Enable the clocks
+DATA 4 0x53f8000c 0x1fffffff
+DATA 4 0x53f80010 0xffffffff
+DATA 4 0x53f80014 0xfdfff
diff --git a/board/eukrea/cpuimx25/lowlevel_init.S b/board/eukrea/cpuimx25/lowlevel_init.S
new file mode 100644
index 0000000..76e4e6f
--- /dev/null
+++ b/board/eukrea/cpuimx25/lowlevel_init.S
@@ -0,0 +1,113 @@
+/*
+ * (C) Copyright 2009 DENX Software Engineering
+ * (C) Copyright 2012 Eukrea Electromatique <www.eukrea.com>
+ * Eric Benard <eric at eukrea.com>
+ *
+ * Based on tx25 and zmx25:
+ * Author: John Rigby <jrigby at gmail.com>
+ *
+ * Based on U-Boot and RedBoot sources for several different i.mx
+ * platforms.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <asm/macro.h>
+#include <asm/arch/macro.h>
+#include <asm/arch/imx-regs.h>
+#include <generated/asm-offsets.h>
+
+.macro init_m3if
+	write32 0xb8003000, 0x1
+.endm
+
+.macro init_clocks
+	write32	0x53f80064, 0x00000000
+	write32	0x53f80008, 0x20034000
+
+	/*
+	 * enable all implemented clocks in all three
+	 * clock control registers
+	 */
+	write32	0x53f8000c, 0x1fffffff
+	write32	0x53f80010, 0xffffffff
+	write32	0x53f80014, 0xfdfff
+.endm
+
+.macro init_lpddr
+	/* Skip SDRAM initialization if we run from RAM */
+	cmp	pc, #0x80000000
+	bls	1f
+	cmp	pc, #0x90000000
+	bhi	1f
+
+	mov	pc, lr
+
+1:	ldr	r0, =IMX_ESDRAMC_BASE
+	ldr	r2, =IMX_SDRAM_BANK0_BASE
+
+	/*
+	 * reset SDRAM controller
+	 * then wait for initialization to complete
+	 */
+	ldr	r1, =(1 << 1) | (1 << 2) | (1 << 3)
+	str	r1, [r0, #ESDRAMC_ESDMISC]
+2:	ldr	r3, [r0, #ESDRAMC_ESDMISC]
+	tst	r3, #(1 << 31)
+	beq	2b
+	ldr	r1, =(1 << 2)
+	str	r1, [r0, #ESDRAMC_ESDMISC]
+
+	ldr	r1, =0x00295729
+	str	r1, [r0, #ESDRAMC_ESDCFG0]
+
+	/* control | precharge */
+	ldr	r1, =0x92100000
+	str	r1, [r0, #ESDRAMC_ESDCTL0]
+	/* dram command encoded in address */
+	strb	r1, [r2, #0x400]
+
+	/* auto refresh */
+	ldr	r1, =0xa2100000
+	str	r1, [r0, #ESDRAMC_ESDCTL0]
+	/* read dram twice to auto refresh */
+	str	r3, [r2]
+	str     r3, [r2]
+
+	/* control | load mode */
+	ldr	r1, =0xb2100000
+	str	r1, [r0, #ESDRAMC_ESDCTL0]
+
+	/* mode register of lpddram */
+	strb	r1, [r2, #0x33]
+
+	/* extended mode register of lpddrram */
+	ldr	r2, =0x81000000
+	strb	r1, [r2]
+
+	/* control | normal */
+	ldr	r1, =0x82216080
+	str	r1, [r0, #ESDRAMC_ESDCTL0]
+.endm
+
+.globl lowlevel_init
+lowlevel_init:
+	init_aips
+	init_max
+	init_m3if
+	init_clocks
+	init_lpddr
+	mov	pc, lr
diff --git a/boards.cfg b/boards.cfg
index 091c79f..2cd6e4d 100644
--- a/boards.cfg
+++ b/boards.cfg
@@ -176,6 +176,8 @@ dockstar                     arm         arm926ejs   -                   Seagate
 tk71                         arm         arm926ejs   tk71                karo           kirkwood
 devkit3250                   arm         arm926ejs   devkit3250          timll          lpc32xx
 jadecpu                      arm         arm926ejs   jadecpu             syteco         mb86r0x
+cpuimx25                     arm         arm926ejs   cpuimx25            eukrea         mx25		cpuimx25:IMX_CONFIG=board/eukrea/cpuimx25/imximage.cfg
+cpuimx25nand                 arm         arm926ejs   cpuimx25            eukrea         mx25		cpuimx25:NAND_U_BOOT
 mx25pdk                      arm         arm926ejs   mx25pdk             freescale      mx25		mx25pdk:IMX_CONFIG=board/freescale/mx25pdk/imximage.cfg
 tx25                         arm         arm926ejs   tx25                karo           mx25
 zmx25                        arm         arm926ejs   zmx25               syteco         mx25
diff --git a/include/configs/cpuimx25.h b/include/configs/cpuimx25.h
new file mode 100644
index 0000000..dc0a1d6
--- /dev/null
+++ b/include/configs/cpuimx25.h
@@ -0,0 +1,198 @@
+/*
+ * (C) Copyright 2009 DENX Software Engineering
+ * (C) Copyright 2012 Eukrea Electromatique <www.eukrea.com>
+ * Eric Benard <eric at eukrea.com>
+ *
+ * Based on tx25.c:
+ * Author: John Rigby <jrigby at gmail.com>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+/*
+ * Eukrea CPUIMX25 board - SoC Configuration
+ */
+#define CONFIG_MX25
+#define CONFIG_MX25_CLK32		32768	/* OSC32K frequency */
+#define CONFIG_SYS_HZ			1000
+
+#define	CONFIG_SYS_MONITOR_LEN		(256 << 10)	/* 256 kB for U-Boot */
+
+#ifndef MACH_TYPE_EUKREA_CPUIMX25SD
+#define MACH_TYPE_EUKREA_CPUIMX25SD	2820
+#endif
+
+#define CONFIG_MACH_TYPE MACH_TYPE_EUKREA_CPUIMX25SD
+
+#ifdef CONFIG_NAND_SPL
+/* Start copying real U-boot from the second page */
+#define CONFIG_SYS_NAND_U_BOOT_OFFS	0x800
+#define CONFIG_SYS_NAND_U_BOOT_SIZE	(CONFIG_SYS_MONITOR_LEN - \
+		CONFIG_SYS_NAND_U_BOOT_OFFS)
+
+#define CONFIG_SYS_NAND_U_BOOT_DST      (0x81200000)
+#define CONFIG_SYS_NAND_U_BOOT_START    CONFIG_SYS_NAND_U_BOOT_DST
+
+#define CONFIG_SYS_NAND_PAGE_SIZE	2048
+#define CONFIG_SYS_NAND_SPARE_SIZE	64
+#define CONFIG_SYS_NAND_BLOCK_SIZE	(128 * 1024)
+#define CONFIG_SYS_NAND_PAGE_COUNT	64
+#define CONFIG_SYS_NAND_SIZE		(256 * 1024 * 1024)
+#define CONFIG_SYS_NAND_BAD_BLOCK_POS	0
+#endif
+
+#define CONFIG_DISPLAY_CPUINFO
+
+#define CONFIG_CMDLINE_TAG			/* enable passing of ATAGs */
+#define CONFIG_SETUP_MEMORY_TAGS
+#define CONFIG_INITRD_TAG
+
+/*
+ * Memory Info
+ */
+/* malloc() len */
+#define CONFIG_SYS_MALLOC_LEN		(1 << 20)	/* 1 MiB */
+/*
+ * Board has 2 32MB banks of DRAM but there is a bug when using
+ * both so only the first is configured
+ */
+#define CONFIG_NR_DRAM_BANKS	1
+
+#define PHYS_SDRAM_1		0x80000000
+#define PHYS_SDRAM_1_SIZE	0x04000000
+
+/* 8MB DRAM test */
+#define CONFIG_SYS_MEMTEST_START	PHYS_SDRAM_1
+#define CONFIG_SYS_MEMTEST_END		(PHYS_SDRAM_1+0x0800000)
+
+/*
+ * Serial Info
+ */
+#define CONFIG_MXC_UART
+#define CONFIG_MXC_UART_BASE	UART1_BASE
+#define CONFIG_CONS_INDEX	1	/* use UART0 for console */
+#define CONFIG_BAUDRATE		115200	/* Default baud rate */
+
+#define CONFIG_MXC_GPIO
+
+/*
+ * MMC
+ */
+#if 0
+#define CONFIG_FSL_ESDHC
+#define CONFIG_SYS_FSL_ESDHC_ADDR	(0x53FB4000)
+#define CONFIG_SYS_FSL_ESDHC_NUM	1
+#define CONFIG_SYS_FSL_ESDHC_USE_PIO	1
+#endif
+
+#define CONFIG_MMC
+#define CONFIG_CMD_MMC
+#define CONFIG_GENERIC_MMC
+#define CONFIG_CMD_FAT
+#define CONFIG_DOS_PARTITION
+
+/*
+ * Flash & Environment
+ */
+/* No NOR flash present */
+#define CONFIG_SYS_NO_FLASH
+#define	CONFIG_ENV_OFFSET	CONFIG_SYS_MONITOR_LEN
+#define CONFIG_ENV_SIZE		(128 * 1024)	/* 128 kB NAND block size */
+#define CONFIG_ENV_OFFSET_REDUND	(CONFIG_ENV_OFFSET + CONFIG_ENV_SIZE)
+
+/* NAND */
+#define	CONFIG_ENV_IS_IN_NAND
+#define CONFIG_NAND_MXC
+#define CONFIG_NAND_MXC_V1_1
+#define CONFIG_MXC_NAND_REGS_BASE	(0xBB000000)
+#define CONFIG_SYS_MAX_NAND_DEVICE	1
+#define CONFIG_SYS_NAND_BASE		(0xBB000000)
+#define CONFIG_JFFS2_NAND
+#define CONFIG_MXC_NAND_HWECC
+#define CONFIG_SYS_NAND_LARGEPAGE
+
+/* U-Boot general configuration */
+#define CONFIG_SYS_PROMPT	"CPUIMX25 U-Boot > "
+#define CONFIG_SYS_CBSIZE	1024	/* Console I/O Buffer Size  */
+/* Print buffer sz */
+#define CONFIG_SYS_PBSIZE	(CONFIG_SYS_CBSIZE + \
+		sizeof(CONFIG_SYS_PROMPT) + 16)
+#define CONFIG_SYS_MAXARGS	32	/* max number of command args */
+/* Boot Argument Buffer Size */
+#define CONFIG_SYS_BARGSIZE	CONFIG_SYS_CBSIZE
+#define CONFIG_CMDLINE_EDITING
+#define CONFIG_SYS_LONGHELP
+
+/* U-Boot commands */
+#include <config_cmd_default.h>
+#define CONFIG_CMD_NAND
+#define CONFIG_CMD_CACHE
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_PING
+
+/*
+ * Ethernet
+ */
+#define CONFIG_FEC_MXC
+#define CONFIG_FEC_MXC_PHYADDR		0
+#define CONFIG_MII
+#define CONFIG_CMD_NET
+#define CONFIG_BOARD_LATE_INIT
+#define CONFIG_ENV_OVERWRITE
+
+#define CONFIG_BOOTDELAY	5
+
+#define CONFIG_LOADADDR		0x81000000	/* loadaddr env var */
+#define CONFIG_SYS_LOAD_ADDR	CONFIG_LOADADDR
+
+#define xstr(s)	str(s)
+#define str(s)	#s
+
+#define CONFIG_HOSTNAME "eukrea-cpuimx25"
+#define	CONFIG_EXTRA_ENV_SETTINGS					\
+	"netdev=eth0\0"							\
+	"nfsargs=setenv bootargs root=/dev/nfs rw "			\
+		"nfsroot=${serverip}:${rootpath}\0"			\
+	"ramargs=setenv bootargs root=/dev/ram rw\0"			\
+	"addip=setenv bootargs ${bootargs} "				\
+		"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}"	\
+		":${hostname}:${netdev}:off panic=1\0"			\
+	"addtty=setenv bootargs ${bootargs}"				\
+		" console=ttymxc0,${baudrate}\0"			\
+	"addmtd=setenv bootargs ${bootargs} ${mtdparts}\0"		\
+	"addmisc=setenv bootargs ${bootargs}\0"				\
+	"u-boot="CONFIG_HOSTNAME"/u-boot-"CONFIG_HOSTNAME".bin\0"	\
+	"kernel_addr_r=" xstr(CONFIG_LOADADDR) "\0"			\
+	"hostname="CONFIG_HOSTNAME"\0"					\
+	"bootfile="CONFIG_HOSTNAME"/uImage-"CONFIG_HOSTNAME".bin\0"	\
+	"rootpath=/srv/nfs/"CONFIG_HOSTNAME"\0"				\
+	"net_nfs=tftp ${kernel_addr_r} ${bootfile};"			\
+		"run nfsargs addip addtty addmtd addmisc;"		\
+		"bootm\0"						\
+	"bootcmd=run net_nfs\0"						\
+	"load=tftp ${loadaddr} ${u-boot}\0"				\
+	"update=nand erase 0 40000;nand write ${loadaddr} 0 40000\0"	\
+	"upd=run load update\0"						\
+
+/* additions for new relocation code, must be added to all boards */
+#define CONFIG_SYS_SDRAM_BASE		PHYS_SDRAM_1
+#define CONFIG_SYS_INIT_SP_ADDR		(CONFIG_SYS_SDRAM_BASE + 0x1000 - \
+					GENERATED_GBL_DATA_SIZE)
+
+#endif /* __CONFIG_H */
diff --git a/nand_spl/board/eukrea/cpuimx25/Makefile b/nand_spl/board/eukrea/cpuimx25/Makefile
new file mode 100644
index 0000000..d8b19c6
--- /dev/null
+++ b/nand_spl/board/eukrea/cpuimx25/Makefile
@@ -0,0 +1,79 @@
+#
+# (C) Copyright 2009 DENX Software Engineering
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundatio; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+CONFIG_NAND_SPL	= y
+
+include $(TOPDIR)/config.mk
+include $(TOPDIR)/nand_spl/board/$(BOARDDIR)/config.mk
+
+nandobj	:= $(OBJTREE)/nand_spl/
+
+LDSCRIPT= $(TOPDIR)/nand_spl/board/$(BOARDDIR)/u-boot.lds
+LDFLAGS := -T $(nandobj)u-boot.lds -Ttext $(CONFIG_SYS_TEXT_BASE) $(LDFLAGS) \
+	   $(LDFLAGS_FINAL)
+AFLAGS	+= -DCONFIG_SPL_BUILD -DCONFIG_NAND_SPL
+CFLAGS	+= -DCONFIG_SPL_BUILD -DCONFIG_NAND_SPL
+
+SOBJS	= start.o lowlevel_init.o
+COBJS	= nand_boot_fsl_nfc.o
+
+SRCS	:= $(SRCTREE)/nand_spl/nand_boot_fsl_nfc.c
+SRCS	+= $(SRCTREE)/arch/arm/cpu/arm926ejs/start.S
+SRCS	+= $(SRCTREE)/board/eukrea/cpuimx25/lowlevel_init.S
+OBJS	:= $(addprefix $(obj),$(SOBJS) $(COBJS))
+__OBJS	:= $(SOBJS) $(COBJS)
+LNDIR	:= $(nandobj)board/$(BOARDDIR)
+
+ALL	= $(nandobj)u-boot-spl $(nandobj)u-boot-spl.bin $(nandobj)u-boot-spl-16k.bin
+
+all:	$(obj).depend $(ALL)
+
+$(nandobj)u-boot-spl-16k.bin: $(nandobj)u-boot-spl
+	$(OBJCOPY) ${OBJCFLAGS} --pad-to=$(PAD_TO) -O binary $< $@
+
+$(nandobj)u-boot-spl.bin:	$(nandobj)u-boot-spl
+	$(OBJCOPY) ${OBJCFLAGS} -O binary $< $@
+
+$(nandobj)u-boot-spl:	$(OBJS) $(nandobj)u-boot.lds
+	cd $(LNDIR) && $(LD) $(LDFLAGS) $(__OBJS) \
+		-Map $(nandobj)u-boot-spl.map \
+		-o $@
+
+$(nandobj)u-boot.lds: $(LDSCRIPT)
+	$(CPP) $(CPPFLAGS) $(LDPPFLAGS) -ansi -D__ASSEMBLY__ -P - <$^ >$@
+
+#########################################################################
+
+$(obj)%.o:	$(SRCTREE)/arch/arm/cpu/arm926ejs/%.S
+	$(CC) $(AFLAGS) -c -o $@ $<
+
+$(obj)%.o:	$(SRCTREE)/board/eukrea/cpuimx25/%.S
+	$(CC) $(AFLAGS) -c -o $@ $<
+
+$(obj)%.o:	$(SRCTREE)/nand_spl/%.c
+	$(CC) $(CFLAGS) -c -o $@ $<
+
+# defines $(obj).depend target
+include $(SRCTREE)/rules.mk
+
+sinclude $(obj).depend
+
+#########################################################################
diff --git a/nand_spl/board/eukrea/cpuimx25/config.mk b/nand_spl/board/eukrea/cpuimx25/config.mk
new file mode 100644
index 0000000..68afbf1
--- /dev/null
+++ b/nand_spl/board/eukrea/cpuimx25/config.mk
@@ -0,0 +1 @@
+PAD_TO	:= 2048
diff --git a/nand_spl/board/eukrea/cpuimx25/u-boot.lds b/nand_spl/board/eukrea/cpuimx25/u-boot.lds
new file mode 100644
index 0000000..d2b08f6
--- /dev/null
+++ b/nand_spl/board/eukrea/cpuimx25/u-boot.lds
@@ -0,0 +1,83 @@
+/*
+ * (C) Copyright 2009
+ * Wolfgang Denk, DENX Software Engineering, wd at denx.de.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+OUTPUT_FORMAT("elf32-littlearm", "elf32-littlearm", "elf32-littlearm")
+OUTPUT_ARCH(arm)
+ENTRY(_start)
+SECTIONS
+{
+	. = 0x00000000;
+
+	. = ALIGN(4);
+	.text :
+	{
+		start.o			(.text)
+		lowlevel_init.o		(.text)
+		nand_boot_fsl_nfc.o	(.text)
+		*(.text)
+		. = 2K;
+	}
+
+	. = ALIGN(4);
+	.rodata : { *(.rodata) }
+
+	. = ALIGN(4);
+	.data : {
+		*(.data)
+	}
+
+	. = ALIGN(4);
+	__u_boot_cmd_start = .;
+	.u_boot_cmd : { *(.u_boot_cmd) }
+	__u_boot_cmd_end = .;
+
+	. = ALIGN(4);
+
+	.rel.dyn : {
+		__rel_dyn_start = .;
+		*(.rel*)
+		__rel_dyn_end = .;
+	}
+
+	.dynsym : {
+		__dynsym_start = .;
+		*(.dynsym)
+	}
+
+	_end = .;
+
+	.bss __rel_dyn_start (OVERLAY) : {
+		__bss_start = .;
+		*(.bss)
+		 . = ALIGN(4);
+		__bss_end__ = .;
+	}
+
+	/DISCARD/ : { *(.bss*) }
+	/DISCARD/ : { *(.dynstr*) }
+	/DISCARD/ : { *(.dynsym*) }
+	/DISCARD/ : { *(.dynamic*) }
+	/DISCARD/ : { *(.hash*) }
+	/DISCARD/ : { *(.plt*) }
+	/DISCARD/ : { *(.interp*) }
+	/DISCARD/ : { *(.gnu*) }
+}
-- 
1.7.7.6



More information about the U-Boot mailing list