[U-Boot] [PATCH v2 1/6] h2200: Add support for iPAQ h2200 palmtop

Marek Vasut marex at denx.de
Sun Sep 23 23:31:57 CEST 2012


Dear Łukasz Dałek,

> On 23.09.2012 23:04, Marek Vasut wrote:
> > Dear Łukasz Dałek,
> > 
> >> On 23.09.2012 22:52, Marek Vasut wrote:
> >>> Dear Łukasz Dałek,
> >>> 
> >>>> On 23.09.2012 22:05, Marek Vasut wrote:
> >>>>> Dear Łukasz Dałek,
> >>>>> 
> >>>>>> On 23.09.2012 21:31, Marek Vasut wrote:
> >>>>>>> Dear Łukasz Dałek,
> >>>>>>> 
> >>>>>>>> On 23.09.2012 17:43, Marek Vasut wrote:
> >>>>>>>>>> +	gd->ram_size = CONFIG_SYS_SDRAM_SIZE;
> >>>>>>>>>> +	return 0;
> >>>>>>>>>> +}
> >>>>>>>>>> diff --git a/board/h2200/h2200.h b/board/h2200/h2200.h
> >>>>>>>>>> new file mode 100644
> >>>>>>>>> 
> >>>>>>>>> Do you need this file at all? Can the udc_disconnect() not be put
> >>>>>>>>> somewhere into usb.h ?
> >>>>>>>> 
> >>>>>>>> Can I just move this declaration into h2200.c?
> >>>>>>> 
> >>>>>>> extern ... ? No, checkpatch will scream and extern is prohibited
> >>>>>>> for a good reason.
> >>>>>> 
> >>>>>> So where should I put it?
> >>>>> 
> >>>>> Isn't it a general call? some include/usb.h ?
> >>>> 
> >>>> For old layer maybe it is.
> >>>> 
> >>>> I'm not sure but include/usb.h is for device implementing usb host but
> >>>> pxa can only be device.
> >>> 
> >>> PXA can be both, actually u-boot is mostly about host. Just put it
> >>> there.
> >>> 
> >>>> Including usb.h generate error.
> >>>> 
> >>>> I'm going to add sd card support and other functions, maybe leaving it
> >>>> would be better idea?
> >>> 
> >>> Why do you think usb.h is not a good place ?
> >> 
> >> Because:
> >> #if defined(CONFIG_USB_UHCI) || defined(CONFIG_USB_OHCI) || \
> >> 
> >>       defined(CONFIG_USB_EHCI) || defined(CONFIG_USB_OHCI_NEW) || \
> >>       defined(CONFIG_USB_SL811HS) || defined(CONFIG_USB_ISP116X_HCD) ||
> >>       \ defined(CONFIG_USB_R8A66597_HCD) || defined(CONFIG_USB_DAVINCI)
> >>       || \ defined(CONFIG_USB_OMAP3) || defined(CONFIG_USB_DA8XX) || \
> >>       defined(CONFIG_USB_BLACKFIN) || defined(CONFIG_USB_AM35X)
> >> 
> >> ...
> >> #else
> >> #error USB Lowlevel not defined
> >> #endif
> >> 
> >> All of these definitions are usb host implementation (maybe OTG too) but
> >> pxa cannot be host.
> > 
> > PXA2xx is OHCI host with one OTG port.
> 
>  From pxa255 documentation:
> "The UDC supports 16 endpoints and can operate half-duplex at a rate of
> 12 Mbps (as a slave only,
> not as a host or hub controller)."
> 
> > what about include/usb/pxa27x_udc.h ... btw can't pxa27x and pxa25x UDC
> > use the same driver?
> 
> pxa27x_udc driver is using older layer which doesn't work with usb
> ethernet driver.
> 
> Btw. pxa27x can be host, pxa25x can't.

Can you update the new gadget driver to be compatible with pxa27x then ?

> Łukasz Dałek

Best regards,
Marek Vasut


More information about the U-Boot mailing list