[U-Boot] [PATCH V3] exynos: spl: Add a custom spi copy function
Minkyu Kang
mk7.kang at samsung.com
Mon Dec 2 09:48:31 CET 2013
On 09/10/13 16:55, Rajeshwari Birje wrote:
> Hi Minkyu Kang,
>
> Since this patch is related to arch/arm spi booting, I had a doubt
> where would it get merged in u-boot-samsung.git or u-boot-spi.git.
>
> This patch is based on "[U-Boot] [PATCH 4/4] spi: exynos: Support word
> transfers" which is already merged in u-boot-spi.git.
Now, that patch is merged to u-boot-samsung.
Anyway I'm OK to pick this patch to u-boot-spi.
>
> Regards,
> Rajeshwari Shinde.
>
> On Tue, Oct 8, 2013 at 6:42 PM, Rajeshwari S Shinde
> <rajeshwari.s at samsung.com> wrote:
>> This patch implements a custom spi_copy funtion to copy u-boot from SF
>> to RAM. This is faster then iROM spi_copy funtion as this runs spi at
>> 50Mhz and also in WORD mode of operation.
>>
>> Changed a printf in pinmux.c to debug just to avoid the compilation
>> error in SPL.
>>
>> Signed-off-by: Alim Akhtar <alim.akhtar at samsung.com>
>> Signed-off-by: Tom Wai-Hong Tam <waihong at chromium.org>
>> Signed-off-by: Rajeshwari S Shinde <rajeshwari.s at samsung.com>
>> ---
>> Based on following patch yet to be merged:
>> "[U-Boot] [PATCH 4/4] spi: exynos: Support word transfers"
>> Changes in V2:
>> - Corrected the commit message.
>> - Added a SPI timeout check.
>> - Corrected the comments.
>> Changes in V3:
>> - Rebased on the latest u-boot-spi tree.
>> arch/arm/cpu/armv7/exynos/pinmux.c | 2 +-
>> arch/arm/cpu/armv7/exynos/spl_boot.c | 122 ++++++++++++++++++++++++++++++++-
>> arch/arm/include/asm/arch-exynos/spi.h | 1 +
>> include/configs/exynos5250-dt.h | 2 +
>> 4 files changed, 123 insertions(+), 4 deletions(-)
>>
>> diff --git a/arch/arm/cpu/armv7/exynos/pinmux.c b/arch/arm/cpu/armv7/exynos/pinmux.c
>> index 8002bce..74cc700 100644
>> --- a/arch/arm/cpu/armv7/exynos/pinmux.c
>> +++ b/arch/arm/cpu/armv7/exynos/pinmux.c
>> @@ -462,7 +462,7 @@ static int exynos4_pinmux_config(int peripheral, int flags)
>> case PERIPH_ID_SDMMC1:
>> case PERIPH_ID_SDMMC3:
>> case PERIPH_ID_SDMMC4:
>> - printf("SDMMC device %d not implemented\n", peripheral);
>> + debug("SDMMC device %d not implemented\n", peripheral);
unrelated change.
>> return -1;
>> default:
>> debug("%s: invalid peripheral %d", __func__, peripheral);
>> diff --git a/arch/arm/cpu/armv7/exynos/spl_boot.c b/arch/arm/cpu/armv7/exynos/spl_boot.c
>> index 3651c00..6faf13f 100644
>> --- a/arch/arm/cpu/armv7/exynos/spl_boot.c
>> +++ b/arch/arm/cpu/armv7/exynos/spl_boot.c
>> @@ -10,8 +10,11 @@
>> #include <asm/arch/clock.h>
>> #include <asm/arch/clk.h>
>> #include <asm/arch/dmc.h>
>> +#include <asm/arch/periph.h>
>> +#include <asm/arch/pinmux.h>
>> #include <asm/arch/power.h>
>> #include <asm/arch/spl.h>
>> +#include <asm/arch/spi.h>
>>
>> #include "common_setup.h"
>> #include "clock_init.h"
>> @@ -59,6 +62,119 @@ static int config_branch_prediction(int set_cr_z)
>> }
>> #endif
>>
>> +static void spi_rx_tx(struct exynos_spi *regs, int todo,
>> + void *dinp, void const *doutp, int i)
>> +{
>> + uint *rxp = (uint *)(dinp + (i * (32 * 1024)));
>> + int rx_lvl, tx_lvl;
>> + uint out_bytes, in_bytes;
>> +
>> + out_bytes = todo;
>> + in_bytes = todo;
>> + setbits_le32(®s->ch_cfg, SPI_CH_RST);
>> + clrbits_le32(®s->ch_cfg, SPI_CH_RST);
>> + writel(((todo * 8) / 32) | SPI_PACKET_CNT_EN, ®s->pkt_cnt);
>> +
>> + while (in_bytes) {
>> + uint32_t spi_sts;
>> + int temp;
>> +
>> + spi_sts = readl(®s->spi_sts);
>> + rx_lvl = ((spi_sts >> 15) & 0x7f);
>> + tx_lvl = ((spi_sts >> 6) & 0x7f);
>> + while (tx_lvl < 32 && out_bytes) {
>> + temp = 0xffffffff;
>> + writel(temp, ®s->tx_data);
>> + out_bytes -= 4;
>> + tx_lvl += 4;
>> + }
>> + while (rx_lvl >= 4 && in_bytes) {
>> + temp = readl(®s->rx_data);
>> + if (rxp)
>> + *rxp++ = temp;
>> + in_bytes -= 4;
>> + rx_lvl -= 4;
>> + }
>> + }
>> +}
>> +
>> +/*
>> + * Copy uboot from spi flash to RAM
>> + *
>> + * @parma uboot_size size of u-boot to copy
>> + * @param uboot_addr address in u-boot to copy
>> + */
>> +static void exynos_spi_copy(unsigned int uboot_size, unsigned int uboot_addr)
>> +{
>> + int upto, todo;
>> + int i, timeout = 100;
>> + struct exynos_spi *regs = (struct exynos_spi *)CONFIG_ENV_SPI_BASE;
>> +
>> + set_spi_clk(PERIPH_ID_SPI1, 50000000); /* set spi clock to 50Mhz */
>> + /* set the spi1 GPIO */
>> + exynos_pinmux_config(PERIPH_ID_SPI1, PINMUX_FLAG_NONE);
>> +
>> + /* set pktcnt and enable it */
>> + writel(4 | SPI_PACKET_CNT_EN, ®s->pkt_cnt);
>> + /* set FB_CLK_SEL */
>> + writel(SPI_FB_DELAY_180, ®s->fb_clk);
>> + /* set CH_WIDTH and BUS_WIDTH as word */
>> + setbits_le32(®s->mode_cfg, SPI_MODE_CH_WIDTH_WORD |
>> + SPI_MODE_BUS_WIDTH_WORD);
>> + clrbits_le32(®s->ch_cfg, SPI_CH_CPOL_L); /* CPOL: active high */
>> +
>> + /* clear rx and tx channel if set priveously */
>> + clrbits_le32(®s->ch_cfg, SPI_RX_CH_ON | SPI_TX_CH_ON);
>> +
>> + setbits_le32(®s->swap_cfg, SPI_RX_SWAP_EN |
>> + SPI_RX_BYTE_SWAP |
>> + SPI_RX_HWORD_SWAP);
>> +
>> + /* do a soft reset */
>> + setbits_le32(®s->ch_cfg, SPI_CH_RST);
>> + clrbits_le32(®s->ch_cfg, SPI_CH_RST);
>> +
>> + /* now set rx and tx channel ON */
>> + setbits_le32(®s->ch_cfg, SPI_RX_CH_ON | SPI_TX_CH_ON | SPI_CH_HS_EN);
>> + clrbits_le32(®s->cs_reg, SPI_SLAVE_SIG_INACT); /* CS low */
>> +
>> + /* Send read instruction (0x3h) followed by a 24 bit addr */
>> + writel((SF_READ_DATA_CMD << 24) | SPI_FLASH_UBOOT_POS, ®s->tx_data);
>> +
>> + /* waiting for TX done */
>> + while (!(readl(®s->spi_sts) & SPI_ST_TX_DONE)) {
>> + if (!timeout) {
>> + debug("SPI TIMEOUT\n");
>> + break;
>> + }
>> + timeout--;
>> + }
>> +
>> + for (upto = 0, i = 0; upto < uboot_size; upto += todo, i++) {
>> + todo = min(uboot_size - upto, (1 << 15));
>> + spi_rx_tx(regs, todo, (void *)(uboot_addr),
>> + (void *)(SPI_FLASH_UBOOT_POS), i);
>> + }
>> +
>> + setbits_le32(®s->cs_reg, SPI_SLAVE_SIG_INACT);/* make the CS high */
>> +
>> + /*
>> + * Let put controller mode to BYTE as
>> + * SPI driver does not support WORD mode yet
>> + */
>> + clrbits_le32(®s->mode_cfg, SPI_MODE_CH_WIDTH_WORD |
>> + SPI_MODE_BUS_WIDTH_WORD);
>> + writel(0, ®s->swap_cfg);
>> +
>> + /*
>> + * Flush spi tx, rx fifos and reset the SPI controller
>> + * and clear rx/tx channel
>> + */
>> + clrsetbits_le32(®s->ch_cfg, SPI_CH_HS_EN, SPI_CH_RST);
>> + clrbits_le32(®s->ch_cfg, SPI_CH_RST);
>> + clrbits_le32(®s->ch_cfg, SPI_TX_CH_ON | SPI_RX_CH_ON);
>> +}
>> +
>> /*
>> * Copy U-boot from mmc to RAM:
>> * COPY_BL2_FNPTR_ADDR: Address in iRAM, which Contains
>> @@ -70,6 +186,7 @@ void copy_uboot_to_ram(void)
>>
>> u32 (*copy_bl2)(u32 offset, u32 nblock, u32 dst) = NULL;
>> u32 offset = 0, size = 0;
>> + struct spl_machine_param *param = spl_get_machine_params();
>> #ifdef CONFIG_SUPPORT_EMMC_BOOT
>> u32 (*copy_bl2_from_emmc)(u32 nblock, u32 dst);
>> void (*end_bootop_from_emmc)(void);
>> @@ -91,9 +208,8 @@ void copy_uboot_to_ram(void)
>> switch (bootmode) {
>> #ifdef CONFIG_SPI_BOOTING
>> case BOOT_MODE_SERIAL:
>> - offset = SPI_FLASH_UBOOT_POS;
>> - size = CONFIG_BL2_SIZE;
>> - copy_bl2 = get_irom_func(SPI_INDEX);
>> + /* Customised function to copy u-boot from SF */
>> + exynos_spi_copy(param->uboot_size, CONFIG_SYS_TEXT_BASE);
>> break;
>> #endif
>> case BOOT_MODE_MMC:
>> diff --git a/arch/arm/include/asm/arch-exynos/spi.h b/arch/arm/include/asm/arch-exynos/spi.h
>> index 147c1a7..0ba931b 100644
>> --- a/arch/arm/include/asm/arch-exynos/spi.h
>> +++ b/arch/arm/include/asm/arch-exynos/spi.h
>> @@ -30,6 +30,7 @@ struct exynos_spi {
>> #define EXYNOS_SPI_MAX_FREQ 50000000
>>
>> #define SPI_TIMEOUT_MS 10
>> +#define SF_READ_DATA_CMD 0x3
>>
>> /* SPI_CHCFG */
>> #define SPI_CH_HS_EN (1 << 6)
>> diff --git a/include/configs/exynos5250-dt.h b/include/configs/exynos5250-dt.h
>> index 8c21909..1d32396 100644
>> --- a/include/configs/exynos5250-dt.h
>> +++ b/include/configs/exynos5250-dt.h
>> @@ -154,6 +154,7 @@
>> #define COPY_BL2_FNPTR_ADDR 0x02020030
>>
>> #define CONFIG_SPL_LIBCOMMON_SUPPORT
>> +#define CONFIG_SPL_GPIO_SUPPORT
>>
>> /* specific .lds file */
>> #define CONFIG_SPL_LDSCRIPT "board/samsung/common/exynos-uboot-spl.lds"
>> @@ -292,6 +293,7 @@
>> /* SPI */
>> #define CONFIG_ENV_IS_IN_SPI_FLASH
>> #define CONFIG_SPI_FLASH
>> +#define CONFIG_ENV_SPI_BASE 0x12D30000
>>
>> #ifdef CONFIG_SPI_FLASH
>> #define CONFIG_EXYNOS_SPI
>> --
>> 1.7.12.4
>>
>> _______________________________________________
>> U-Boot mailing list
>> U-Boot at lists.denx.de
>> http://lists.denx.de/mailman/listinfo/u-boot
>
>
>
Thanks,
Minkyu Kang.
More information about the U-Boot
mailing list