[U-Boot] [PATCH v2 2/5] arm: omap3: Add SPL support to tao3530

[Stefan Roese]

Add SPL support for the Technexion TAO3530 SOM to replace
x-loader. Tested with the Thunder baseboard. Currently this is
only tested with the TAO3530 SOM revision (Ax/Bx).

Tested by booting via MMC and NAND.

Signed-off-by: Stefan Roese <sr at denx.de>
Cc: Tapani Utriainen <tapani at technexion.com>
Cc: Thorsten Eisbein <thorsten.eisbein at head-acoustics.de>
Cc: Tom Rini <trini at ti.com>
---
v2:
- Added CONFIG_NAND_OMAP_ECCSCHEME

 board/technexion/tao3530/tao3530.c | 27 +++++++++++++++-
 include/configs/tao3530.h          | 65 ++++++++++++++++++++++++++++++++++++++
 2 files changed, 91 insertions(+), 1 deletion(-)

diff --git a/board/technexion/tao3530/tao3530.c b/board/technexion/tao3530/tao3530.c
index 0668c25..9268d38 100644
--- a/board/technexion/tao3530/tao3530.c
+++ b/board/technexion/tao3530/tao3530.c
@@ -67,6 +67,31 @@ out:
 	return ret;
 }
 
+#ifdef CONFIG_SPL_BUILD
+/*
+ * Routine: get_board_mem_timings
+ * Description: If we use SPL then there is no x-loader nor config header
+ * so we have to setup the DDR timings ourself on both banks.
+ */
+void get_board_mem_timings(struct board_sdrc_timings *timings)
+{
+	if (tao3530_revision() < 3) {
+		/* 256MB / Bank */
+		timings->mcfg = MCFG(256 << 20, 14);	/* RAS-width 14 */
+		timings->ctrla = HYNIX_V_ACTIMA_165;
+		timings->ctrlb = HYNIX_V_ACTIMB_165;
+	} else {
+		/* 128MB / Bank */
+		timings->mcfg = MCFG(128 << 20, 13);	/* RAS-width 13 */
+		timings->ctrla = MICRON_V_ACTIMA_165;
+		timings->ctrlb = MICRON_V_ACTIMB_165;
+	}
+
+	timings->mr = MICRON_V_MR_165;
+	timings->rfr_ctrl = SDP_3430_SDRC_RFR_CTRL_165MHz;
+}
+#endif
+
 /*
  * Routine: board_init
  * Description: Early hardware init.
@@ -134,7 +159,7 @@ void set_muxconf_regs(void)
 	MUX_TAO3530();
 }
 
-#ifdef CONFIG_GENERIC_MMC
+#if defined(CONFIG_GENERIC_MMC) && !defined(CONFIG_SPL_BUILD)
 int board_mmc_init(bd_t *bis)
 {
 	omap_mmc_init(0, 0, 0, -1, -1);
diff --git a/include/configs/tao3530.h b/include/configs/tao3530.h
index e2d5b48..81aa9cc 100644
--- a/include/configs/tao3530.h
+++ b/include/configs/tao3530.h
@@ -5,6 +5,8 @@
  * Edward Lin <linuxfae at technexion.com>
  * Tapani Utriainen <linuxfae at technexion.com>
  *
+ * Copyright (C) 2013 Stefan Roese <sr at denx.de>
+ *
  * SPDX-License-Identifier:	GPL-2.0+
  */
 
@@ -298,4 +300,67 @@
 #define CONFIG_USB_STORAGE
 #define CONGIG_CMD_STORAGE
 
+/* Defines for SPL */
+#define CONFIG_SPL
+#define CONFIG_SPL_FRAMEWORK
+#define CONFIG_SPL_NAND_SIMPLE
+
+#define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR	0x300 /* address 0x60000 */
+#define CONFIG_SYS_U_BOOT_MAX_SIZE_SECTORS	0x200 /* 256 KB */
+#define CONFIG_SYS_MMC_SD_FAT_BOOT_PARTITION	1
+#define CONFIG_SPL_FAT_LOAD_PAYLOAD_NAME	"u-boot.img"
+
+#define CONFIG_SPL_BOARD_INIT
+#define CONFIG_SPL_LIBCOMMON_SUPPORT
+#define CONFIG_SPL_LIBDISK_SUPPORT
+#define CONFIG_SPL_I2C_SUPPORT
+#define CONFIG_SPL_LIBGENERIC_SUPPORT
+#define CONFIG_SPL_MMC_SUPPORT
+#define CONFIG_SPL_FAT_SUPPORT
+#define CONFIG_SPL_SERIAL_SUPPORT
+#define CONFIG_SPL_NAND_SUPPORT
+#define CONFIG_SPL_NAND_BASE
+#define CONFIG_SPL_NAND_DRIVERS
+#define CONFIG_SPL_NAND_ECC
+#define CONFIG_SPL_GPIO_SUPPORT
+#define CONFIG_SPL_POWER_SUPPORT
+#define CONFIG_SPL_OMAP3_ID_NAND
+#define CONFIG_SPL_LDSCRIPT		"$(CPUDIR)/omap-common/u-boot-spl.lds"
+
+/* NAND boot config */
+#define CONFIG_SYS_NAND_5_ADDR_CYCLE
+#define CONFIG_SYS_NAND_PAGE_COUNT	64
+#define CONFIG_SYS_NAND_PAGE_SIZE	2048
+#define CONFIG_SYS_NAND_OOBSIZE		64
+#define CONFIG_SYS_NAND_BLOCK_SIZE	(128 * 1024)
+#define CONFIG_SYS_NAND_BAD_BLOCK_POS	NAND_LARGE_BADBLOCK_POS
+/*
+ * Use the ECC/OOB layout from omap_gpmc.h that matches your chip:
+ * SP vs LP, 8bit vs 16bit: GPMC_NAND_HW_ECC_LAYOUT
+ */
+#define CONFIG_SYS_NAND_ECCPOS		{ 2, 3, 4, 5, 6, 7, 8, 9, \
+					 10, 11, 12, 13 }
+#define CONFIG_SYS_NAND_ECCSIZE		512
+#define CONFIG_SYS_NAND_ECCBYTES	3
+#define CONFIG_NAND_OMAP_ECCSCHEME	OMAP_ECC_HAM1_CODE_HW
+
+#define CONFIG_SYS_NAND_U_BOOT_START	CONFIG_SYS_TEXT_BASE
+#define CONFIG_SYS_NAND_U_BOOT_OFFS	0x80000
+
+#define CONFIG_SPL_TEXT_BASE		0x40200800
+#define CONFIG_SPL_MAX_SIZE		(54 * 1024)	/* 8 KB for stack */
+#define CONFIG_SPL_STACK		LOW_LEVEL_SRAM_STACK
+
+/*
+ * Use 0x80008000 as TEXT_BASE here for compatibility reasons with the
+ * older x-loader implementations. And move the BSS area so that it
+ * doesn't overlap with TEXT_BASE.
+ */
+#define CONFIG_SYS_TEXT_BASE		0x80008000
+#define CONFIG_SPL_BSS_START_ADDR	0x80100000
+#define CONFIG_SPL_BSS_MAX_SIZE		0x80000		/* 512 KB */
+
+#define CONFIG_SYS_SPL_MALLOC_START	0x80208000
+#define CONFIG_SYS_SPL_MALLOC_SIZE	0x100000
+
 #endif /* __CONFIG_H */
-- 
1.8.4.4