[U-Boot] [PATCH 2/5] port wandboards to use the generic distro configs

[Robert Nelson]

On Thu, Dec 5, 2013 at 8:18 PM, Dennis Gilmore <dennis at ausil.us> wrote:
> Signed-off-by: Dennis Gilmore <dennis at ausil.us>
> ---
>  include/configs/wandboard.h | 40 +++++++++++++++++++++++++++++++++++-----
>  1 file changed, 35 insertions(+), 5 deletions(-)
>
> diff --git a/include/configs/wandboard.h b/include/configs/wandboard.h
> index e9c7e64..02d8968 100644
> --- a/include/configs/wandboard.h
> +++ b/include/configs/wandboard.h
> @@ -40,6 +40,9 @@
>  #define CONFIG_CONS_INDEX              1
>  #define CONFIG_BAUDRATE                        115200
>
> +/* enable generic distro config */
> +#define DISTRO_DEFAULTS 1
> +
>  /* Command definition */
>  #include <config_cmd_default.h>
>
> @@ -48,7 +51,6 @@
>  #define CONFIG_CMD_BMODE
>  #define CONFIG_CMD_SETEXPR
>
> -#define CONFIG_BOOTDELAY               5
>
>  #define CONFIG_SYS_MEMTEST_START       0x10000000
>  #define CONFIG_SYS_MEMTEST_END         (CONFIG_SYS_MEMTEST_START + 500 * SZ_1M)
> @@ -65,6 +67,9 @@
>  #define CONFIG_CMD_MMC
>  #define CONFIG_GENERIC_MMC
>  #define CONFIG_BOUNCE_BUFFER
> +
> +#define CONFIG_BOOTDELAY               5
> +
>  #define CONFIG_CMD_EXT2
>  #define CONFIG_CMD_FAT
>  #define CONFIG_DOS_PARTITION
> @@ -74,6 +79,11 @@
>  #define CONFIG_CMD_DHCP
>  #define CONFIG_CMD_MII
>  #define CONFIG_CMD_NET
> +
> +#define CONFIG_OF_LIBFDT
> +#define CONFIG_CMD_BOOTZ
> +
> +/* Ethernet Configuration */
>  #define CONFIG_FEC_MXC
>  #define CONFIG_MII
>  #define IMX_FEC_BASE                   ENET_BASE_ADDR
> @@ -113,8 +123,30 @@
>         "fdt_high=0xffffffff\0" \
>         "initrd_high=0xffffffff\0" \
>         "fdt_file=" CONFIG_DEFAULT_FDT_FILE "\0" \
> -       "fdt_addr=0x11000000\0" \
> +       "fdt_addr=0x11100000\0" \
> +       "fdt_addr_r=0x11200000\0" \
> +       "pxefile_addr_r=0x11300000\0" \
> +       "scr_addr_r=0x11400000\0" \
> +       "kernel_addr_r=0x11500000\0" \
> +       "ramdisk_addr_r=0x13500000\0" \
>         "boot_fdt=try\0" \
> +       "bootcmd_setup=mmc rescan\0" \
> +       "bootcmd_pxe=setenv bootfile \"\" ;dhcp; tftp ${fdt_addr} /dtb/${fdt_file}; pxe get; pxe boot\0" \
> +       "bootcmd_disk_scr=ext2load ${boot_ifc} ${bootdevice} ${scr_addr_r} boot.scr &&

Why all the non-generic "ext2load"'s? use just "load", then it'll work
with both fat, ext2/3/4 & btrfs...

Regards,

-- 
Robert Nelson
http://www.rcn-ee.com/