[U-Boot] [PATCH v2 35/35] doc: Update the zynq u-boot status

Jagannadha Sutradharudu Teki jagannadha.sutradharudu-teki at xilinx.com
Wed Dec 18 16:30:20 CET 2013


Updated doc/README.zynq to current status.

Signed-off-by: Jagannadha Sutradharudu Teki <jaganna at xilinx.com>
---
V2: none

 doc/README.zynq | 29 +++++++++++++++++++----------
 1 file changed, 19 insertions(+), 10 deletions(-)

diff --git a/doc/README.zynq b/doc/README.zynq
index 7cb87e3..732ef3f 100644
--- a/doc/README.zynq
+++ b/doc/README.zynq
@@ -28,7 +28,16 @@ and I/O programmability.
   - zc770-xm012 (nor)
   - zc770-xm013 (dual parallel qspi, gem1)
 
-3. Bootmode
+3. Building
+
+# Configure for microzed board
+  $ make zynq_microzed_config
+    Configuring for zynq_microzed board...
+
+# Building
+  $ make DEVICE_TREE=zynq-microzed
+
+4. Bootmode
 
 Zynq has a facility to read the bootmode from the slcr bootmode register
 once user is setting through jumpers on the board - see page no:1546 on [5]
@@ -50,11 +59,11 @@ SLCR bootmode register Bit[3:0] values
 "modeboot" variable can assign any of "qspiboot", "norboot", "nandboot",
 "sdboot" or "jtagboot" bootmode strings at runtime.
 
-4. Mainline status
+5. Mainline status
 
 - Added basic board configurations support.
 - Added zynq u-boot bsp code - arch/arm/cpu/armv7/zynq
-- Added zynq boards named - zynq, zynq_dcc
+- Add zynq boards support - zc70x, zed, microzed, zc770
 - Added zynq drivers:
   serial - drivers/serial/serial_zynq.c
   net - drivers/net/zynq_gem.c
@@ -62,15 +71,15 @@ SLCR bootmode register Bit[3:0] values
   mmc - drivers/mmc/zynq_sdhci.c
   spi-  drivers/spi/zynq_spi.c
   i2c - drivers/i2c/zynq_i2c.c
+  qspi - drivers/spi/zynq_qspi.c
+  nand - drivers/mtd/nand/zynq_nand.c
+- Done proper cleanups on board configurations
+- Added basic FDT support for zynq boards
+- d-cache support for zynq_gem.c
 
-5. TODO
+6. TODO
 
-- Add zynq boards support - zc70x, zed, microzed, zc770
-- Add zynq qspi controller driver
-- Add zynq nand controller driver
-- d-cache support for zynq_gem.c
-- FDT support for zynq boards
-- Need proper cleanups on board configurations
+- Add FDT support on individual drivers.
 
 [1] http://www.xilinx.com/products/boards-and-kits/EK-Z7-ZC702-G.htm
 [2] http://www.xilinx.com/products/boards-and-kits/EK-Z7-ZC706-G.htm
-- 
1.8.3




More information about the U-Boot mailing list