[U-Boot] [PATCH V2 5/7] smdk5420: Implement callbacks needed by exynos_fb driver
Simon Glass
sjg at chromium.org
Thu Dec 19 21:40:09 CET 2013
Hi Ajay,
On 12 November 2013 05:27, Ajay Kumar <ajaykumar.rs at samsung.com> wrote:
> Add callbacks to set up DP-HPD, backlight and LCD power
> on SMDK5420.
>
> Signed-off-by: Ajay Kumar <ajaykumar.rs at samsung.com>
> ---
> board/samsung/smdk5420/smdk5420.c | 102 +++++++-------------------------------
> 1 file changed, 17 insertions(+), 85 deletions(-)
>
> diff --git a/board/samsung/smdk5420/smdk5420.c b/board/samsung/smdk5420/smdk5420.c
> index d85b953..75b22cc 100644
> --- a/board/samsung/smdk5420/smdk5420.c
> +++ b/board/samsung/smdk5420/smdk5420.c
> @@ -43,98 +43,30 @@ int exynos_init(void)
> }
>
> #ifdef CONFIG_LCD
> -void cfg_lcd_gpio(void)
> +void exynos_cfg_lcd_gpio(void)
> {
> - struct exynos5_gpio_part1 *gpio1 =
> - (struct exynos5_gpio_part1 *)samsung_get_base_gpio_part1();
> -
> - /* For Backlight */
> - s5p_gpio_cfg_pin(&gpio1->b2, 0, GPIO_OUTPUT);
> - s5p_gpio_set_value(&gpio1->b2, 0, 1);
> -
> - /* LCD power on */
> - s5p_gpio_cfg_pin(&gpio1->x1, 5, GPIO_OUTPUT);
> - s5p_gpio_set_value(&gpio1->x1, 5, 1);
> + struct exynos5420_gpio_part2 *gpio2 =
> + (struct exynos5420_gpio_part2 *)samsung_get_base_gpio_part2();
>
> /* Set Hotplug detect for DP */
> - s5p_gpio_cfg_pin(&gpio1->x0, 7, GPIO_FUNC(0x3));
> + s5p_gpio_cfg_pin(&gpio2->x0, 7, GPIO_FUNC(0x3));
> }
>
> -vidinfo_t panel_info = {
> - .vl_freq = 60,
> - .vl_col = 2560,
> - .vl_row = 1600,
> - .vl_width = 2560,
> - .vl_height = 1600,
> - .vl_clkp = CONFIG_SYS_LOW,
> - .vl_hsp = CONFIG_SYS_LOW,
> - .vl_vsp = CONFIG_SYS_LOW,
> - .vl_dp = CONFIG_SYS_LOW,
> - .vl_bpix = 4, /* LCD_BPP = 2^4, for output conosle on LCD */
> -
> - /* wDP panel timing infomation */
> - .vl_hspw = 32,
> - .vl_hbpd = 80,
> - .vl_hfpd = 48,
> -
> - .vl_vspw = 6,
> - .vl_vbpd = 37,
> - .vl_vfpd = 3,
> - .vl_cmd_allow_len = 0xf,
> -
> - .win_id = 3,
> - .cfg_gpio = cfg_lcd_gpio,
> - .backlight_on = NULL,
> - .lcd_power_on = NULL,
> - .reset_lcd = NULL,
> - .dual_lcd_enabled = 0,
> -
> - .init_delay = 0,
> - .power_on_delay = 0,
> - .reset_delay = 0,
> - .interface_mode = FIMD_RGB_INTERFACE,
> - .dp_enabled = 1,
> -};
> -
> -static struct edp_device_info edp_info = {
> - .disp_info = {
> - .h_res = 2560,
> - .h_sync_width = 32,
> - .h_back_porch = 80,
> - .h_front_porch = 48,
> - .v_res = 1600,
> - .v_sync_width = 6,
> - .v_back_porch = 37,
> - .v_front_porch = 3,
> - .v_sync_rate = 60,
> - },
> - .lt_info = {
> - .lt_status = DP_LT_NONE,
> - },
> - .video_info = {
> - .master_mode = 0,
> - .bist_mode = DP_DISABLE,
> - .bist_pattern = NO_PATTERN,
> - .h_sync_polarity = 0,
> - .v_sync_polarity = 0,
> - .interlaced = 0,
> - .color_space = COLOR_RGB,
> - .dynamic_range = VESA,
> - .ycbcr_coeff = COLOR_YCBCR601,
> - .color_depth = COLOR_8,
> - },
> -};
> -
> -static struct exynos_dp_platform_data dp_platform_data = {
> - .phy_enable = set_dp_phy_ctrl,
> - .edp_dev_info = &edp_info,
> -};
> -
> -void init_panel_info(vidinfo_t *vid)
> +void exynos_backlight_on(unsigned int onoff)
> {
> - vid->rgb_mode = MODE_RGB_P,
> + struct exynos5420_gpio_part1 *gpio1 =
> + (struct exynos5420_gpio_part1 *)samsung_get_base_gpio_part1();
> +
> + struct exynos5420_gpio_part2 *gpio2 =
> + (struct exynos5420_gpio_part2 *)samsung_get_base_gpio_part2();
> +
> + /* For PWM */
> + s5p_gpio_cfg_pin(&gpio1->b2, 0, GPIO_OUTPUT);
> + s5p_gpio_set_value(&gpio1->b2, 0, 1);
Can we use generic GPIO calls instead? gpio_set_value(), etc.
>
> - exynos_set_dp_platform_data(&dp_platform_data);
> + /* BL_EN */
> + s5p_gpio_cfg_pin(&gpio2->x1, 5, GPIO_OUTPUT);
> + s5p_gpio_set_value(&gpio2->x1, 5, 1);
> }
> #endif
>
> --
> 1.7.12.4
>
Regards,
Simon
More information about the U-Boot
mailing list