[U-Boot] [PATCH] TI:omap3: Drop omap3_zoom2
Tom Rini
trini at ti.com
Fri Dec 20 17:19:33 CET 2013
The omap3_zoom2 board has not been updated for a correct CONFIG_SYS_HZ
and Tom Rix's email has long been bouncing.
Signed-off-by: Tom Rini <trini at ti.com>
---
board/logicpd/zoom2/Makefile | 11 --
board/logicpd/zoom2/config.mk | 17 ---
board/logicpd/zoom2/debug_board.c | 44 -------
board/logicpd/zoom2/led.c | 116 ------------------
board/logicpd/zoom2/zoom2.c | 183 ----------------------------
board/logicpd/zoom2/zoom2.h | 142 ---------------------
board/logicpd/zoom2/zoom2_serial.c | 130 --------------------
board/logicpd/zoom2/zoom2_serial.h | 59 ---------
boards.cfg | 1 -
drivers/serial/ns16550.c | 5 +-
include/configs/omap3_zoom2.h | 237 ------------------------------------
11 files changed, 2 insertions(+), 943 deletions(-)
delete mode 100644 board/logicpd/zoom2/Makefile
delete mode 100644 board/logicpd/zoom2/config.mk
delete mode 100644 board/logicpd/zoom2/debug_board.c
delete mode 100644 board/logicpd/zoom2/led.c
delete mode 100644 board/logicpd/zoom2/zoom2.c
delete mode 100644 board/logicpd/zoom2/zoom2.h
delete mode 100644 board/logicpd/zoom2/zoom2_serial.c
delete mode 100644 board/logicpd/zoom2/zoom2_serial.h
delete mode 100644 include/configs/omap3_zoom2.h
diff --git a/board/logicpd/zoom2/Makefile b/board/logicpd/zoom2/Makefile
deleted file mode 100644
index 8ec5f25..0000000
--- a/board/logicpd/zoom2/Makefile
+++ /dev/null
@@ -1,11 +0,0 @@
-#
-# (C) Copyright 2000, 2001, 2002
-# Wolfgang Denk, DENX Software Engineering, wd at denx.de.
-#
-# SPDX-License-Identifier: GPL-2.0+
-#
-
-obj-y := zoom2.o
-obj-y += debug_board.o
-obj-y += zoom2_serial.o
-obj-$(CONFIG_STATUS_LED) += led.o
diff --git a/board/logicpd/zoom2/config.mk b/board/logicpd/zoom2/config.mk
deleted file mode 100644
index 1c382f7..0000000
--- a/board/logicpd/zoom2/config.mk
+++ /dev/null
@@ -1,17 +0,0 @@
-#
-# (C) Copyright 2009
-# Texas Instruments, <www.ti.com>
-#
-# Zoom II uses OMAP3 (ARM-CortexA8) CPU
-# see http://www.ti.com/ for more information on Texas Instruments
-#
-# SPDX-License-Identifier: GPL-2.0+
-#
-# Physical Address:
-# 0x80000000 (bank0)
-# 0xA0000000 (bank1)
-# Linux-Kernel is expected to be at 0x80008000, entry 0x80008000
-# (mem base + reserved)
-
-# For use with external or internal boots.
-CONFIG_SYS_TEXT_BASE = 0x80008000
diff --git a/board/logicpd/zoom2/debug_board.c b/board/logicpd/zoom2/debug_board.c
deleted file mode 100644
index 071f410..0000000
--- a/board/logicpd/zoom2/debug_board.c
+++ /dev/null
@@ -1,44 +0,0 @@
-/*
- * Copyright (c) 2009 Wind River Systems, Inc.
- * Tom Rix <Tom.Rix at windriver.com>
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-#include <common.h>
-#include <asm/arch/cpu.h>
-#include <asm/io.h>
-#include <asm/arch/mux.h>
-#include <asm/gpio.h>
-
-#define DEBUG_BOARD_CONNECTED 1
-#define DEBUG_BOARD_NOT_CONNECTED 0
-
-static int debug_board_connected = DEBUG_BOARD_CONNECTED;
-
-static void zoom2_debug_board_detect (void)
-{
- int val = 0;
-
- if (!gpio_request(158, "")) {
- /*
- * GPIO to query for debug board
- * 158 db board query
- */
- gpio_direction_input(158);
- val = gpio_get_value(158);
- }
-
- if (!val)
- debug_board_connected = DEBUG_BOARD_NOT_CONNECTED;
-}
-
-int zoom2_debug_board_connected (void)
-{
- static int first_time = 1;
-
- if (first_time) {
- zoom2_debug_board_detect ();
- first_time = 0;
- }
- return debug_board_connected;
-}
diff --git a/board/logicpd/zoom2/led.c b/board/logicpd/zoom2/led.c
deleted file mode 100644
index 5d37ac1..0000000
--- a/board/logicpd/zoom2/led.c
+++ /dev/null
@@ -1,116 +0,0 @@
-/*
- * Copyright (c) 2009 Wind River Systems, Inc.
- * Tom Rix <Tom.Rix at windriver.com>
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-#include <common.h>
-#include <status_led.h>
-#include <asm/arch/cpu.h>
-#include <asm/io.h>
-#include <asm/arch/sys_proto.h>
-#include <asm/gpio.h>
-
-static unsigned int saved_state[2] = {STATUS_LED_OFF, STATUS_LED_OFF};
-
-/*
- * GPIO LEDs
- * 173 red
- * 154 blue
- * 61 blue2
- */
-#define ZOOM2_LED_RED 173
-#define ZOOM2_LED_BLUE 154
-#define ZOOM2_LED_BLUE2 61
-
-void red_led_off(void)
-{
- /* red */
- if (!gpio_request(ZOOM2_LED_RED, "")) {
- gpio_direction_output(ZOOM2_LED_RED, 0);
- gpio_set_value(ZOOM2_LED_RED, 0);
- }
- saved_state[STATUS_LED_RED] = STATUS_LED_OFF;
-}
-
-void blue_led_off(void)
-{
- /* blue */
- if (!gpio_request(ZOOM2_LED_BLUE, "")) {
- gpio_direction_output(ZOOM2_LED_BLUE, 0);
- gpio_set_value(ZOOM2_LED_BLUE, 0);
- }
-
- /* blue 2 */
- if (!gpio_request(ZOOM2_LED_BLUE2, "")) {
- gpio_direction_output(ZOOM2_LED_BLUE2, 0);
- gpio_set_value(ZOOM2_LED_BLUE2, 0);
- }
- saved_state[STATUS_LED_BLUE] = STATUS_LED_OFF;
-}
-
-void red_led_on(void)
-{
- blue_led_off();
-
- /* red */
- if (!gpio_request(ZOOM2_LED_RED, "")) {
- gpio_direction_output(ZOOM2_LED_RED, 0);
- gpio_set_value(ZOOM2_LED_RED, 1);
- }
- saved_state[STATUS_LED_RED] = STATUS_LED_ON;
-}
-
-void blue_led_on(void)
-{
- red_led_off();
-
- /* blue */
- if (!gpio_request(ZOOM2_LED_BLUE, "")) {
- gpio_direction_output(ZOOM2_LED_BLUE, 0);
- gpio_set_value(ZOOM2_LED_BLUE, 1);
- }
-
- /* blue 2 */
- if (!gpio_request(ZOOM2_LED_BLUE2, "")) {
- gpio_direction_output(ZOOM2_LED_BLUE2, 0);
- gpio_set_value(ZOOM2_LED_BLUE2, 1);
- }
-
- saved_state[STATUS_LED_BLUE] = STATUS_LED_ON;
-}
-
-void __led_init (led_id_t mask, int state)
-{
- __led_set (mask, state);
-}
-
-void __led_toggle (led_id_t mask)
-{
- if (STATUS_LED_BLUE == mask) {
- if (STATUS_LED_ON == saved_state[STATUS_LED_BLUE])
- blue_led_off();
- else
- blue_led_on();
- } else if (STATUS_LED_RED == mask) {
- if (STATUS_LED_ON == saved_state[STATUS_LED_RED])
- red_led_off();
- else
- red_led_on();
- }
-}
-
-void __led_set (led_id_t mask, int state)
-{
- if (STATUS_LED_BLUE == mask) {
- if (STATUS_LED_ON == state)
- blue_led_on();
- else
- blue_led_off();
- } else if (STATUS_LED_RED == mask) {
- if (STATUS_LED_ON == state)
- red_led_on();
- else
- red_led_off();
- }
-}
diff --git a/board/logicpd/zoom2/zoom2.c b/board/logicpd/zoom2/zoom2.c
deleted file mode 100644
index e14de04..0000000
--- a/board/logicpd/zoom2/zoom2.c
+++ /dev/null
@@ -1,183 +0,0 @@
-/*
- * Copyright (c) 2009 Wind River Systems, Inc.
- * Tom Rix <Tom.Rix at windriver.com>
- *
- * Derived from Zoom1 code by
- * Nishanth Menon <nm at ti.com>
- * Sunil Kumar <sunilsaini05 at gmail.com>
- * Shashi Ranjan <shashiranjanmca05 at gmail.com>
- * Richard Woodruff <r-woodruff2 at ti.com>
- * Syed Mohammed Khasim <khasim at ti.com>
- *
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-#include <common.h>
-#include <netdev.h>
-#ifdef CONFIG_STATUS_LED
-#include <status_led.h>
-#endif
-#include <twl4030.h>
-#include <asm/io.h>
-#include <asm/arch/mmc_host_def.h>
-#include <asm/gpio.h>
-#include <asm/arch/mem.h>
-#include <asm/arch/mux.h>
-#include <asm/arch/sys_proto.h>
-#include <asm/mach-types.h>
-#include "zoom2.h"
-#include "zoom2_serial.h"
-
-DECLARE_GLOBAL_DATA_PTR;
-
-/*
- * This the the zoom2, board specific, gpmc configuration for the
- * quad uart on the debug board. The more general gpmc configurations
- * are setup at the cpu level in arch/arm/cpu/armv7/omap3/mem.c
- *
- * The details of the setting of the serial gpmc setup are not available.
- * The values were provided by another party.
- */
-static u32 gpmc_serial_TL16CP754C[GPMC_MAX_REG] = {
- 0x00011000,
- 0x001F1F01,
- 0x00080803,
- 0x1D091D09,
- 0x041D1F1F,
- 0x1D0904C4, 0
-};
-
-/* Used to track the revision of the board */
-static zoom2_revision revision = ZOOM2_REVISION_UNKNOWN;
-
-/*
- * Routine: zoom2_get_revision
- * Description: Return the revision of the Zoom2 this code is running on.
- */
-zoom2_revision zoom2_get_revision(void)
-{
- return revision;
-}
-
-/*
- * Routine: zoom2_identify
- * Description: Detect which version of Zoom2 we are running on.
- */
-void zoom2_identify(void)
-{
- /*
- * To check for production board vs beta board,
- * check if gpio 94 is clear.
- *
- * No way yet to check for alpha board identity.
- * Alpha boards were produced in very limited quantities
- * and they are not commonly used. They are mentioned here
- * only for completeness.
- */
- if (!gpio_request(94, "")) {
- unsigned int val;
-
- gpio_direction_input(94);
- val = gpio_get_value(94);
-
- if (val)
- revision = ZOOM2_REVISION_BETA;
- else
- revision = ZOOM2_REVISION_PRODUCTION;
- }
-
- printf("Board revision ");
- switch (revision) {
- case ZOOM2_REVISION_PRODUCTION:
- printf("Production\n");
- break;
- case ZOOM2_REVISION_BETA:
- printf("Beta\n");
- break;
- default:
- printf("Unknown\n");
- break;
- }
-}
-
-/*
- * Routine: board_init
- * Description: Early hardware init.
- */
-int board_init (void)
-{
- u32 *gpmc_config;
-
- gpmc_init (); /* in SRAM or SDRAM, finish GPMC */
-
- /* Configure console support on zoom2 */
- gpmc_config = gpmc_serial_TL16CP754C;
- enable_gpmc_cs_config(gpmc_config, &gpmc_cfg->cs[3],
- SERIAL_TL16CP754C_BASE, GPMC_SIZE_16M);
-
- /* board id for Linux */
- gd->bd->bi_arch_number = MACH_TYPE_OMAP_ZOOM2;
- /* boot param addr */
- gd->bd->bi_boot_params = (OMAP34XX_SDRC_CS0 + 0x100);
-
-#if defined(CONFIG_STATUS_LED) && defined(STATUS_LED_BOOT)
- status_led_set (STATUS_LED_BOOT, STATUS_LED_ON);
-#endif
- return 0;
-}
-
-/*
- * Routine: misc_init_r
- * Description: Configure zoom board specific configurations
- */
-int misc_init_r(void)
-{
- zoom2_identify();
- twl4030_power_init();
- twl4030_led_init(TWL4030_LED_LEDEN_LEDAON | TWL4030_LED_LEDEN_LEDBON);
- dieid_num_r();
-
- /*
- * Board Reset
- * The board is reset by holding the the large button
- * on the top right side of the main board for
- * eight seconds.
- *
- * There are reported problems of some beta boards
- * continously resetting. For those boards, disable resetting.
- */
- if (ZOOM2_REVISION_PRODUCTION <= zoom2_get_revision())
- twl4030_power_reset_init();
-
- return 0;
-}
-
-/*
- * Routine: set_muxconf_regs
- * Description: Setting up the configuration Mux registers specific to the
- * hardware. Many pins need to be moved from protect to primary
- * mode.
- */
-void set_muxconf_regs (void)
-{
- /* platform specific muxes */
- MUX_ZOOM2 ();
-}
-
-#ifdef CONFIG_GENERIC_MMC
-int board_mmc_init(bd_t *bis)
-{
- return omap_mmc_init(0, 0, 0, -1, -1);
-}
-#endif
-
-#ifdef CONFIG_CMD_NET
-int board_eth_init(bd_t *bis)
-{
- int rc = 0;
-#ifdef CONFIG_LAN91C96
- rc = lan91c96_initialize(0, CONFIG_LAN91C96_BASE);
-#endif
- return rc;
-}
-#endif
diff --git a/board/logicpd/zoom2/zoom2.h b/board/logicpd/zoom2/zoom2.h
deleted file mode 100644
index 850c790..0000000
--- a/board/logicpd/zoom2/zoom2.h
+++ /dev/null
@@ -1,142 +0,0 @@
-/*
- * Copyright (c) 2009 Wind River Systems, Inc.
- * Tom Rix <Tom.Rix at windriver.com>
- *
- * Derived from: board/omap3/zoom1/zoom1.h
- * Nishanth Menon <nm at ti.com>
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-#ifndef _BOARD_ZOOM2_H_
-#define _BOARD_ZOOM2_H_
-
-const omap3_sysinfo sysinfo = {
- DDR_STACKED,
- "OMAP3 Zoom2 ",
- "NAND",
-};
-
-typedef enum {
- ZOOM2_REVISION_UNKNOWN = 0,
- ZOOM2_REVISION_ALPHA,
- ZOOM2_REVISION_BETA,
- ZOOM2_REVISION_PRODUCTION
-} zoom2_revision;
-
-zoom2_revision zoom2_get_revision(void);
-
-/*
- * IEN - Input Enable
- * IDIS - Input Disable
- * PTD - Pull type Down
- * PTU - Pull type Up
- * DIS - Pull type selection is inactive
- * EN - Pull type selection is active
- * M0 - Mode 0
- * The commented string gives the final mux configuration for that pin
- */
-#define MUX_ZOOM2() \
- /* SDRC*/\
- MUX_VAL(CP(SDRC_D0), (IEN | PTD | DIS | M0)) /* SDRC_D0 */\
- MUX_VAL(CP(SDRC_D1), (IEN | PTD | DIS | M0)) /* SDRC_D1 */\
- MUX_VAL(CP(SDRC_D2), (IEN | PTD | DIS | M0)) /* SDRC_D2 */\
- MUX_VAL(CP(SDRC_D3), (IEN | PTD | DIS | M0)) /* SDRC_D3 */\
- MUX_VAL(CP(SDRC_D4), (IEN | PTD | DIS | M0)) /* SDRC_D4 */\
- MUX_VAL(CP(SDRC_D5), (IEN | PTD | DIS | M0)) /* SDRC_D5 */\
- MUX_VAL(CP(SDRC_D6), (IEN | PTD | DIS | M0)) /* SDRC_D6 */\
- MUX_VAL(CP(SDRC_D7), (IEN | PTD | DIS | M0)) /* SDRC_D7 */\
- MUX_VAL(CP(SDRC_D8), (IEN | PTD | DIS | M0)) /* SDRC_D8 */\
- MUX_VAL(CP(SDRC_D9), (IEN | PTD | DIS | M0)) /* SDRC_D9 */\
- MUX_VAL(CP(SDRC_D10), (IEN | PTD | DIS | M0)) /* SDRC_D10 */\
- MUX_VAL(CP(SDRC_D11), (IEN | PTD | DIS | M0)) /* SDRC_D11 */\
- MUX_VAL(CP(SDRC_D12), (IEN | PTD | DIS | M0)) /* SDRC_D12 */\
- MUX_VAL(CP(SDRC_D13), (IEN | PTD | DIS | M0)) /* SDRC_D13 */\
- MUX_VAL(CP(SDRC_D14), (IEN | PTD | DIS | M0)) /* SDRC_D14 */\
- MUX_VAL(CP(SDRC_D15), (IEN | PTD | DIS | M0)) /* SDRC_D15 */\
- MUX_VAL(CP(SDRC_D16), (IEN | PTD | DIS | M0)) /* SDRC_D16 */\
- MUX_VAL(CP(SDRC_D17), (IEN | PTD | DIS | M0)) /* SDRC_D17 */\
- MUX_VAL(CP(SDRC_D18), (IEN | PTD | DIS | M0)) /* SDRC_D18 */\
- MUX_VAL(CP(SDRC_D19), (IEN | PTD | DIS | M0)) /* SDRC_D19 */\
- MUX_VAL(CP(SDRC_D20), (IEN | PTD | DIS | M0)) /* SDRC_D20 */\
- MUX_VAL(CP(SDRC_D21), (IEN | PTD | DIS | M0)) /* SDRC_D21 */\
- MUX_VAL(CP(SDRC_D22), (IEN | PTD | DIS | M0)) /* SDRC_D22 */\
- MUX_VAL(CP(SDRC_D23), (IEN | PTD | DIS | M0)) /* SDRC_D23 */\
- MUX_VAL(CP(SDRC_D24), (IEN | PTD | DIS | M0)) /* SDRC_D24 */\
- MUX_VAL(CP(SDRC_D25), (IEN | PTD | DIS | M0)) /* SDRC_D25 */\
- MUX_VAL(CP(SDRC_D26), (IEN | PTD | DIS | M0)) /* SDRC_D26 */\
- MUX_VAL(CP(SDRC_D27), (IEN | PTD | DIS | M0)) /* SDRC_D27 */\
- MUX_VAL(CP(SDRC_D28), (IEN | PTD | DIS | M0)) /* SDRC_D28 */\
- MUX_VAL(CP(SDRC_D29), (IEN | PTD | DIS | M0)) /* SDRC_D29 */\
- MUX_VAL(CP(SDRC_D30), (IEN | PTD | DIS | M0)) /* SDRC_D30 */\
- MUX_VAL(CP(SDRC_D31), (IEN | PTD | DIS | M0)) /* SDRC_D31 */\
- MUX_VAL(CP(SDRC_CLK), (IEN | PTD | DIS | M0)) /* SDRC_CLK */\
- MUX_VAL(CP(SDRC_DQS0), (IEN | PTD | DIS | M0)) /* SDRC_DQS0 */\
- MUX_VAL(CP(SDRC_DQS1), (IEN | PTD | DIS | M0)) /* SDRC_DQS1 */\
- MUX_VAL(CP(SDRC_DQS2), (IEN | PTD | DIS | M0)) /* SDRC_DQS2 */\
- MUX_VAL(CP(SDRC_DQS3), (IEN | PTD | DIS | M0)) /* SDRC_DQS3 */\
-/* GPMC */\
- MUX_VAL(CP(GPMC_A1), (IDIS | PTD | DIS | M0)) /* GPMC_A1 */\
- MUX_VAL(CP(GPMC_A2), (IDIS | PTD | DIS | M0)) /* GPMC_A2 */\
- MUX_VAL(CP(GPMC_A3), (IDIS | PTD | DIS | M0)) /* GPMC_A3 */\
- MUX_VAL(CP(GPMC_A4), (IDIS | PTD | DIS | M0)) /* GPMC_A4 */\
- MUX_VAL(CP(GPMC_A5), (IDIS | PTD | DIS | M0)) /* GPMC_A5 */\
- MUX_VAL(CP(GPMC_A6), (IDIS | PTD | DIS | M0)) /* GPMC_A6 */\
- MUX_VAL(CP(GPMC_A7), (IDIS | PTD | DIS | M0)) /* GPMC_A7 */\
- MUX_VAL(CP(GPMC_A8), (IDIS | PTD | DIS | M0)) /* GPMC_A8 */\
- MUX_VAL(CP(GPMC_A9), (IDIS | PTD | DIS | M0)) /* GPMC_A9 */\
- MUX_VAL(CP(GPMC_A10), (IDIS | PTD | DIS | M0)) /* GPMC_A10 */\
- MUX_VAL(CP(GPMC_D0), (IEN | PTD | DIS | M0)) /* GPMC_D0 */\
- MUX_VAL(CP(GPMC_D1), (IEN | PTD | DIS | M0)) /* GPMC_D1 */\
- MUX_VAL(CP(GPMC_D2), (IEN | PTD | DIS | M0)) /* GPMC_D2 */\
- MUX_VAL(CP(GPMC_D3), (IEN | PTD | DIS | M0)) /* GPMC_D3 */\
- MUX_VAL(CP(GPMC_D4), (IEN | PTD | DIS | M0)) /* GPMC_D4 */\
- MUX_VAL(CP(GPMC_D5), (IEN | PTD | DIS | M0)) /* GPMC_D5 */\
- MUX_VAL(CP(GPMC_D6), (IEN | PTD | DIS | M0)) /* GPMC_D6 */\
- MUX_VAL(CP(GPMC_D7), (IEN | PTD | DIS | M0)) /* GPMC_D7 */\
- MUX_VAL(CP(GPMC_D8), (IEN | PTD | DIS | M0)) /* GPMC_D8 */\
- MUX_VAL(CP(GPMC_D9), (IEN | PTD | DIS | M0)) /* GPMC_D9 */\
- MUX_VAL(CP(GPMC_D10), (IEN | PTD | DIS | M0)) /* GPMC_D10 */\
- MUX_VAL(CP(GPMC_D11), (IEN | PTD | DIS | M0)) /* GPMC_D11 */\
- MUX_VAL(CP(GPMC_D12), (IEN | PTD | DIS | M0)) /* GPMC_D12 */\
- MUX_VAL(CP(GPMC_D13), (IEN | PTD | DIS | M0)) /* GPMC_D13 */\
- MUX_VAL(CP(GPMC_D14), (IEN | PTD | DIS | M0)) /* GPMC_D14 */\
- MUX_VAL(CP(GPMC_D15), (IEN | PTD | DIS | M0)) /* GPMC_D15 */\
- MUX_VAL(CP(GPMC_NCS0), (IDIS | PTU | EN | M0)) /* GPMC_nCS0 */\
- MUX_VAL(CP(GPMC_NCS1), (IDIS | PTU | EN | M7)) /* GPMC_nCS1 */\
- MUX_VAL(CP(GPMC_NCS2), (IDIS | PTU | EN | M7)) /* GPMC_nCS2 */\
- MUX_VAL(CP(GPMC_NCS3), (IDIS | PTU | EN | M7)) /* GPMC_nCS3 */\
- MUX_VAL(CP(GPMC_NCS4), (IDIS | PTU | EN | M7)) /* GPMC_nCS4 */\
- MUX_VAL(CP(GPMC_NCS5), (IDIS | PTD | DIS | M7)) /* GPMC_nCS5 */\
- MUX_VAL(CP(GPMC_NCS6), (IEN | PTD | DIS | M7)) /* GPMC_nCS6 */\
- MUX_VAL(CP(GPMC_NCS7), (IEN | PTU | EN | M7)) /* GPMC_nCS7 */\
- MUX_VAL(CP(GPMC_CLK), (IDIS | PTD | DIS | M0)) /* GPMC_CLK */\
- MUX_VAL(CP(GPMC_NADV_ALE), (IDIS | PTD | DIS | M0)) /* GPMC_nADV_ALE */\
- MUX_VAL(CP(GPMC_NOE), (IDIS | PTD | DIS | M0)) /* GPMC_nOE */\
- MUX_VAL(CP(GPMC_NWE), (IDIS | PTD | DIS | M0)) /* GPMC_nWE */\
- MUX_VAL(CP(GPMC_NWP), (IDIS | PTU | DIS | M0)) /* GPMC_nWP */\
- MUX_VAL(CP(GPMC_NBE0_CLE), (IDIS | PTD | DIS | M0)) /* GPMC_nBE0_CLE */\
- MUX_VAL(CP(GPMC_NBE1), (IEN | PTD | DIS | M0)) /* GPMC_nBE1 */\
- MUX_VAL(CP(GPMC_WAIT0), (IEN | PTD | EN | M0)) /* GPMC_WAIT0 */\
- MUX_VAL(CP(GPMC_WAIT1), (IEN | PTU | EN | M0)) /* GPMC_WAIT1 */\
- MUX_VAL(CP(GPMC_WAIT2), (IEN | PTU | EN | M0)) /* GPMC_WAIT2 */\
- MUX_VAL(CP(GPMC_WAIT3), (IEN | PTU | EN | M0)) /* GPMC_WAIT3 */\
-/* IDCC modem Power On */\
- MUX_VAL(CP(CAM_D11), (IEN | PTU | EN | M4)) /* GPIO_110 */\
- MUX_VAL(CP(CAM_D4), (IEN | PTU | EN | M4)) /* GPIO_103 */\
-/* GPMC CS7 has LAN9211 device */\
- MUX_VAL(CP(GPMC_NCS7), (IDIS | PTU | EN | M0)) /* GPMC_nCS7 */\
- MUX_VAL(CP(MCBSP1_DX), (IEN | PTD | DIS | M4)) /* LAN9221 */\
- MUX_VAL(CP(MCSPI1_CS2), (IEN | PTD | EN | M0)) /* MCSPI1_CS2 */\
-/* GPMC CS3 has Serial TL16CP754C device */\
- MUX_VAL(CP(GPMC_NCS3), (IDIS | PTU | EN | M0)) /* GPMC_nCS3 */\
-/* Toggle Reset pin of TL16CP754C device */\
- MUX_VAL(CP(MCBSP4_CLKX), (IEN | PTU | EN | M4)) /* GPIO_152 */\
- udelay(10);\
- MUX_VAL(CP(MCBSP4_CLKX), (IEN | PTD | EN | M4)) /* GPIO_152 */\
- MUX_VAL(CP(SDRC_CKE1), (IDIS | PTU | EN | M0)) /* SDRC_CKE1 */\
-/* LEDS */\
- MUX_VAL(CP(MCSPI1_SOMI), (IEN | PTD | EN | M4)) /* GPIO_173 red */\
- MUX_VAL(CP(MCBSP4_DX), (IEN | PTD | EN | M4)) /* GPIO_154 blue */\
- MUX_VAL(CP(GPMC_NBE1), (IEN | PTD | EN | M4)) /* GPIO_61 blue2 */
-
-#endif /* _BOARD_ZOOM2_H_ */
diff --git a/board/logicpd/zoom2/zoom2_serial.c b/board/logicpd/zoom2/zoom2_serial.c
deleted file mode 100644
index 2959276..0000000
--- a/board/logicpd/zoom2/zoom2_serial.c
+++ /dev/null
@@ -1,130 +0,0 @@
-/*
- * Copyright (c) 2009 Wind River Systems, Inc.
- * Tom Rix <Tom.Rix at windriver.com>
- *
- * SPDX-License-Identifier: GPL-2.0+
- *
- * This file was adapted from arch/powerpc/cpu/mpc5xxx/serial.c
- */
-
-#include <common.h>
-#include <serial.h>
-#include <ns16550.h>
-#include <asm/arch/cpu.h>
-#include "zoom2_serial.h"
-
-int quad_init_dev (unsigned long base)
-{
- /*
- * The Quad UART is on the debug board.
- * Check if the debug board is attached before using the UART
- */
- if (zoom2_debug_board_connected ()) {
- NS16550_t com_port = (NS16550_t) base;
- int baud_divisor = CONFIG_SYS_NS16550_CLK / 16 /
- CONFIG_BAUDRATE;
-
- /*
- * Zoom2 has a board specific initialization of its UART.
- * This generic initialization has been copied from
- * drivers/serial/ns16550.c. The macros have been expanded.
- *
- * Do the following instead of
- *
- * NS16550_init (com_port, clock_divisor);
- */
- com_port->ier = 0x00;
-
- /*
- * On Zoom2 board Set pre-scalar to 1
- * CLKSEL is GND => MCR[7] is 1 => preslr is 4
- * So change the prescl to 1
- */
- com_port->lcr = 0xBF;
- com_port->fcr |= 0x10;
- com_port->mcr &= 0x7F;
-
- /* This is generic ns16550.c setup */
- com_port->lcr = UART_LCR_BKSE | UART_LCR_8N1;
- com_port->dll = 0;
- com_port->dlm = 0;
- com_port->lcr = UART_LCR_8N1;
- com_port->mcr = UART_MCR_DTR | UART_MCR_RTS;
- com_port->fcr = UART_FCR_FIFO_EN | UART_FCR_RXSR |
- UART_FCR_TXSR;
- com_port->lcr = UART_LCR_BKSE | UART_LCR_8N1;
- com_port->dll = baud_divisor & 0xff;
- com_port->dlm = (baud_divisor >> 8) & 0xff;
- com_port->lcr = UART_LCR_8N1;
- }
- /*
- * We have to lie here, otherwise the board init code will hang
- * on the check
- */
- return 0;
-}
-
-void quad_putc_dev (unsigned long base, const char c)
-{
- if (zoom2_debug_board_connected ()) {
-
- if (c == '\n')
- quad_putc_dev (base, '\r');
-
- NS16550_putc ((NS16550_t) base, c);
- } else {
- usbtty_putc(c);
- }
-}
-
-void quad_puts_dev (unsigned long base, const char *s)
-{
- if (zoom2_debug_board_connected ()) {
- while ((s != NULL) && (*s != '\0'))
- quad_putc_dev (base, *s++);
- } else {
- usbtty_puts(s);
- }
-}
-
-int quad_getc_dev (unsigned long base)
-{
- if (zoom2_debug_board_connected ())
- return NS16550_getc ((NS16550_t) base);
-
- return usbtty_getc();
-}
-
-int quad_tstc_dev (unsigned long base)
-{
- if (zoom2_debug_board_connected ())
- return NS16550_tstc ((NS16550_t) base);
-
- return usbtty_tstc();
-}
-
-void quad_setbrg_dev (unsigned long base)
-{
- if (zoom2_debug_board_connected ()) {
-
- int clock_divisor = CONFIG_SYS_NS16550_CLK / 16 /
- CONFIG_BAUDRATE;
-
- NS16550_reinit ((NS16550_t) base, clock_divisor);
- }
-}
-
-QUAD_INIT (0)
-QUAD_INIT (1)
-QUAD_INIT (2)
-QUAD_INIT (3)
-
-struct serial_device *default_serial_console(void)
-{
- switch (ZOOM2_DEFAULT_SERIAL_DEVICE) {
- case 0: return &zoom2_serial_device0;
- case 1: return &zoom2_serial_device1;
- case 2: return &zoom2_serial_device2;
- case 3: return &zoom2_serial_device3;
- }
-}
diff --git a/board/logicpd/zoom2/zoom2_serial.h b/board/logicpd/zoom2/zoom2_serial.h
deleted file mode 100644
index 8224452..0000000
--- a/board/logicpd/zoom2/zoom2_serial.h
+++ /dev/null
@@ -1,59 +0,0 @@
-/*
- * Copyright (c) 2009 Wind River Systems, Inc.
- * Tom Rix <Tom.Rix at windriver.com>
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#ifndef ZOOM2_SERIAL_H
-#define ZOOM2_SERIAL_H
-
-#include <linux/stringify.h>
-
-extern int zoom2_debug_board_connected (void);
-
-#define SERIAL_TL16CP754C_BASE 0x10000000 /* Zoom2 Serial chip address */
-
-#define QUAD_BASE_0 SERIAL_TL16CP754C_BASE
-#define QUAD_BASE_1 (SERIAL_TL16CP754C_BASE + 0x100)
-#define QUAD_BASE_2 (SERIAL_TL16CP754C_BASE + 0x200)
-#define QUAD_BASE_3 (SERIAL_TL16CP754C_BASE + 0x300)
-
-#define QUAD_INIT(n) \
-int quad_init_##n(void) \
-{ \
- return quad_init_dev(QUAD_BASE_##n); \
-} \
-void quad_setbrg_##n(void) \
-{ \
- quad_setbrg_dev(QUAD_BASE_##n); \
-} \
-void quad_putc_##n(const char c) \
-{ \
- quad_putc_dev(QUAD_BASE_##n, c); \
-} \
-void quad_puts_##n(const char *s) \
-{ \
- quad_puts_dev(QUAD_BASE_##n, s); \
-} \
-int quad_getc_##n(void) \
-{ \
- return quad_getc_dev(QUAD_BASE_##n); \
-} \
-int quad_tstc_##n(void) \
-{ \
- return quad_tstc_dev(QUAD_BASE_##n); \
-} \
-struct serial_device zoom2_serial_device##n = \
-{ \
- .name = __stringify(n), \
- .start = quad_init_##n, \
- .stop = NULL, \
- .setbrg = quad_setbrg_##n, \
- .getc = quad_getc_##n, \
- .tstc = quad_tstc_##n, \
- .putc = quad_putc_##n, \
- .puts = quad_puts_##n, \
-};
-
-#endif /* ZOOM2_SERIAL_H */
diff --git a/boards.cfg b/boards.cfg
index c602a16..9105635 100644
--- a/boards.cfg
+++ b/boards.cfg
@@ -325,7 +325,6 @@ Active arm armv7 omap3 isee igep00x0
Active arm armv7 omap3 logicpd am3517evm am3517_evm - Vaibhav Hiremath <hvaibhav at ti.com>
Active arm armv7 omap3 logicpd omap3som omap3_logic - Peter Barada <peter.barada at logicpd.com>
Active arm armv7 omap3 logicpd zoom1 omap3_zoom1 - Nishanth Menon <nm at ti.com>
-Active arm armv7 omap3 logicpd zoom2 omap3_zoom2 - Tom Rix <Tom.Rix at windriver.com>
Active arm armv7 omap3 matrix_vision mvblx omap3_mvblx - Michael Jones <michael.jones at matrix-vision.de>
Active arm armv7 omap3 nokia rx51 nokia_rx51 - Pali Rohár <pali.rohar at gmail.com>
Active arm armv7 omap3 technexion twister twister - Stefano Babic <sbabic at denx.de>
diff --git a/drivers/serial/ns16550.c b/drivers/serial/ns16550.c
index 181c818..fbc37b2 100644
--- a/drivers/serial/ns16550.c
+++ b/drivers/serial/ns16550.c
@@ -56,9 +56,8 @@ void NS16550_init(NS16550_t com_port, int baud_divisor)
;
serial_out(CONFIG_SYS_NS16550_IER, &com_port->ier);
-#if (defined(CONFIG_OMAP) && !defined(CONFIG_OMAP3_ZOOM2)) || \
- defined(CONFIG_AM33XX) || defined(CONFIG_TI81XX) || \
- defined(CONFIG_AM43XX)
+#if defined(CONFIG_OMAP) || defined(CONFIG_AM33XX) || \
+ defined(CONFIG_TI81XX) || defined(CONFIG_AM43XX)
serial_out(0x7, &com_port->mdr1); /* mode select reset TL16C750*/
#endif
serial_out(UART_LCR_BKSE | UART_LCRVAL, &com_port->lcr);
diff --git a/include/configs/omap3_zoom2.h b/include/configs/omap3_zoom2.h
deleted file mode 100644
index f749740..0000000
--- a/include/configs/omap3_zoom2.h
+++ /dev/null
@@ -1,237 +0,0 @@
-/*
- * (C) Copyright 2006-2009
- * Texas Instruments.
- * Richard Woodruff <r-woodruff2 at ti.com>
- * Syed Mohammed Khasim <x0khasim at ti.com>
- * Nishanth Menon <nm at ti.com>
- * Tom Rix <Tom.Rix at windriver.com>
- *
- * Configuration settings for the TI OMAP3430 Zoom II board.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-/*
- * High Level Configuration Options
- */
-#define CONFIG_OMAP 1 /* in a TI OMAP core */
-#define CONFIG_OMAP34XX 1 /* which is a 34XX */
-#define CONFIG_OMAP3_ZOOM2 1 /* working with Zoom II */
-#define CONFIG_OMAP_GPIO
-#define CONFIG_OMAP_COMMON
-
-#define CONFIG_SDRC /* The chip has SDRC controller */
-
-#include <asm/arch/cpu.h> /* get chip and board defs */
-#include <asm/arch/omap3.h>
-
-/*
- * Display CPU and Board information
- */
-#define CONFIG_DISPLAY_CPUINFO 1
-#define CONFIG_DISPLAY_BOARDINFO 1
-
-/* Clock Defines */
-#define V_OSCK 26000000 /* Clock output from T2 */
-#define V_SCLK (V_OSCK >> 1)
-
-#define CONFIG_MISC_INIT_R
-
-#define CONFIG_CMDLINE_TAG 1 /* enable passing of ATAGs */
-#define CONFIG_SETUP_MEMORY_TAGS 1
-#define CONFIG_INITRD_TAG 1
-#define CONFIG_REVISION_TAG 1
-
-#define CONFIG_OF_LIBFDT 1
-
-/*
- * Size of malloc() pool
- */
-#define CONFIG_ENV_SIZE (128 << 10) /* 128 KiB */
- /* Sector */
-#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + (128 << 10))
-/*
- * Hardware drivers
- */
-
-/*
- * NS16550 Configuration
- * Zoom2 uses the TL16CP754C on the debug board
- */
-/*
- * 0 - 1 : first USB with respect to the left edge of the debug board
- * 2 - 3 : second USB with respect to the left edge of the debug board
- */
-#define ZOOM2_DEFAULT_SERIAL_DEVICE 0
-
-#define V_NS16550_CLK (1843200) /* 1.8432 Mhz */
-
-#define CONFIG_SYS_NS16550
-#define CONFIG_SYS_NS16550_REG_SIZE (-2)
-#define CONFIG_SYS_NS16550_CLK V_NS16550_CLK
-#define CONFIG_BAUDRATE 115200
-#define CONFIG_SYS_BAUDRATE_TABLE {115200}
-
-/* allow to overwrite serial and ethaddr */
-#define CONFIG_ENV_OVERWRITE
-
-#define CONFIG_GENERIC_MMC 1
-#define CONFIG_MMC 1
-#define CONFIG_OMAP_HSMMC 1
-#define CONFIG_DOS_PARTITION 1
-
-/* Status LED */
-#define CONFIG_STATUS_LED 1 /* Status LED enabled */
-#define CONFIG_BOARD_SPECIFIC_LED 1
-#define STATUS_LED_BLUE 0
-#define STATUS_LED_RED 1
-/* Blue */
-#define STATUS_LED_BIT STATUS_LED_BLUE
-#define STATUS_LED_STATE STATUS_LED_ON
-#define STATUS_LED_PERIOD (CONFIG_SYS_HZ / 2)
-/* Red */
-#define STATUS_LED_BIT1 STATUS_LED_RED
-#define STATUS_LED_STATE1 STATUS_LED_OFF
-#define STATUS_LED_PERIOD1 (CONFIG_SYS_HZ / 2)
-/* Optional value */
-#define STATUS_LED_BOOT STATUS_LED_BIT
-
-/* GPIO banks */
-#ifdef CONFIG_STATUS_LED
-#define CONFIG_OMAP3_GPIO_2 /* ZOOM2_LED_BLUE2 */
-#define CONFIG_OMAP3_GPIO_6 /* ZOOM2_LED_RED */
-#endif
-#define CONFIG_OMAP3_GPIO_3 /* board revision */
-#define CONFIG_OMAP3_GPIO_5 /* debug board detection, ZOOM2_LED_BLUE */
-
-/* USB */
-#define CONFIG_MUSB_UDC 1
-#define CONFIG_USB_OMAP3 1
-#define CONFIG_TWL4030_USB 1
-
-/* USB device configuration */
-#define CONFIG_USB_DEVICE 1
-#define CONFIG_USB_TTY 1
-/* Change these to suit your needs */
-#define CONFIG_USBD_VENDORID 0x0451
-#define CONFIG_USBD_PRODUCTID 0x5678
-#define CONFIG_USBD_MANUFACTURER "Texas Instruments"
-#define CONFIG_USBD_PRODUCT_NAME "Zoom2"
-
-/* commands to include */
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_FAT /* FAT support */
-#define CONFIG_CMD_I2C /* I2C serial bus support */
-#define CONFIG_CMD_MMC /* MMC support */
-#define CONFIG_CMD_NAND /* NAND support */
-#define CONFIG_CMD_NAND_LOCK_UNLOCK /* Enable lock/unlock support */
-
-#undef CONFIG_CMD_FLASH /* flinfo, erase, protect */
-#undef CONFIG_CMD_FPGA /* FPGA configuration Support */
-#undef CONFIG_CMD_IMI /* iminfo */
-#undef CONFIG_CMD_IMLS /* List all found images */
-#undef CONFIG_CMD_NET /* bootp, tftpboot, rarpboot */
-#undef CONFIG_CMD_NFS /* NFS support */
-
-#define CONFIG_SYS_NO_FLASH
-#define CONFIG_SYS_I2C
-#define CONFIG_SYS_OMAP24_I2C_SPEED 100000
-#define CONFIG_SYS_OMAP24_I2C_SLAVE 1
-#define CONFIG_SYS_I2C_OMAP34XX
-
-/*
- * TWL4030
- */
-#define CONFIG_TWL4030_POWER 1
-#define CONFIG_TWL4030_LED 1
-
-/*
- * Board NAND Info.
- */
-#define CONFIG_NAND_OMAP_GPMC
-#define CONFIG_SYS_NAND_ADDR NAND_BASE /* physical address */
- /* to access nand */
-#define CONFIG_SYS_NAND_BASE NAND_BASE /* physical address */
- /* to access nand at */
- /* CS0 */
-#define GPMC_NAND_ECC_LP_x16_LAYOUT 1
-#define CONFIG_SYS_MAX_NAND_DEVICE 1
-
-/* Environment information */
-#define CONFIG_BOOTDELAY 10
-
-#define CONFIG_EXTRA_ENV_SETTINGS \
- "usbtty=cdc_acm\0" \
-
-#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_1
-#define CONFIG_SYS_INIT_RAM_ADDR 0x4020f800
-#define CONFIG_SYS_INIT_RAM_SIZE 0x800
-#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_INIT_RAM_ADDR + \
- CONFIG_SYS_INIT_RAM_SIZE - \
- GENERATED_GBL_DATA_SIZE)
-/*
- * Miscellaneous configurable options
- */
-
-#define CONFIG_SYS_PROMPT "OMAP3 Zoom2 # "
-#define CONFIG_SYS_LONGHELP
-#define CONFIG_SYS_CBSIZE 512
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \
- sizeof(CONFIG_SYS_PROMPT) + 16)
-#define CONFIG_SYS_MAXARGS 16
-#define CONFIG_SYS_BARGSIZE (CONFIG_SYS_CBSIZE)
-/* Memtest from start of memory to 31MB */
-#define CONFIG_SYS_MEMTEST_START (OMAP34XX_SDRC_CS0)
-#define CONFIG_SYS_MEMTEST_END (OMAP34XX_SDRC_CS0 + 0x01F00000)
-/* The default load address is the start of memory */
-#define CONFIG_SYS_LOAD_ADDR (OMAP34XX_SDRC_CS0)
-/* everything, incl board info, in Hz */
-#undef CONFIG_SYS_CLKS_IN_HZ
-/*
- * 2430 has 12 GP timers, they can be driven by the SysClk (12/13/19.2) or by
- * 32KHz clk, or from external sig. This rate is divided by a local divisor.
- */
-#define CONFIG_SYS_TIMERBASE (OMAP34XX_GPT2)
-#define CONFIG_SYS_PTV 7 /* 2^(PTV+1) */
-#define CONFIG_SYS_HZ ((V_SCLK) / (2 << CONFIG_SYS_PTV))
-
-/*-----------------------------------------------------------------------
- * Physical Memory Map
- */
-#define CONFIG_NR_DRAM_BANKS 2 /* CS1 may or may not be populated */
-#define PHYS_SDRAM_1 OMAP34XX_SDRC_CS0
-#define PHYS_SDRAM_2 OMAP34XX_SDRC_CS1
-
-/*-----------------------------------------------------------------------
- * FLASH and environment organization
- */
-
-/* **** PISMO SUPPORT *** */
-
-/* Configure the PISMO */
-#define PISMO1_NAND_SIZE GPMC_SIZE_128M
-#define PISMO1_ONEN_SIZE GPMC_SIZE_128M
-
-#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 2 sectors */
-
-#if defined(CONFIG_CMD_NAND)
-#define CONFIG_SYS_FLASH_BASE PISMO1_NAND_BASE
-#endif
-
-/* Monitor at start of flash */
-#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE
-
-#define CONFIG_ENV_IS_IN_NAND 1
-#define SMNAND_ENV_OFFSET 0x0c0000 /* environment starts here */
-
-#define CONFIG_SYS_ENV_SECT_SIZE (128 << 10) /* 128 KiB */
-#define CONFIG_ENV_OFFSET SMNAND_ENV_OFFSET
-#define CONFIG_ENV_ADDR SMNAND_ENV_OFFSET
-
-#define CONFIG_SYS_CACHELINE_SIZE 64
-
-#endif /* __CONFIG_H */
--
1.7.9.5
More information about the U-Boot
mailing list