[U-Boot] [PATCH V2 5/7] smdk5420: Implement callbacks needed by exynos_fb driver

Simon Glass sjg at chromium.org
Fri Dec 20 17:36:39 CET 2013


Hi Ajay,

On 20 December 2013 02:43, Ajay kumar <ajaynumb at gmail.com> wrote:
> Hi Simon,
>
>
> On Fri, Dec 20, 2013 at 2:10 AM, Simon Glass <sjg at chromium.org> wrote:
>>
>> Hi Ajay,
>>
>> On 12 November 2013 05:27, Ajay Kumar <ajaykumar.rs at samsung.com> wrote:
>> > Add callbacks to set up DP-HPD, backlight and LCD power
>> > on SMDK5420.
>> >
>> > Signed-off-by: Ajay Kumar <ajaykumar.rs at samsung.com>
>> > ---
>> >  board/samsung/smdk5420/smdk5420.c | 102
>> > +++++++-------------------------------
>> >  1 file changed, 17 insertions(+), 85 deletions(-)
>> >
>> > diff --git a/board/samsung/smdk5420/smdk5420.c
>> > b/board/samsung/smdk5420/smdk5420.c
>> > index d85b953..75b22cc 100644
>> > --- a/board/samsung/smdk5420/smdk5420.c
>> > +++ b/board/samsung/smdk5420/smdk5420.c
>> > @@ -43,98 +43,30 @@ int exynos_init(void)
>> >  }
>> >
>> >  #ifdef CONFIG_LCD
>> > -void cfg_lcd_gpio(void)
>> > +void exynos_cfg_lcd_gpio(void)
>> >  {
>> > -       struct exynos5_gpio_part1 *gpio1 =
>> > -               (struct exynos5_gpio_part1
>> > *)samsung_get_base_gpio_part1();
>> > -
>> > -       /* For Backlight */
>> > -       s5p_gpio_cfg_pin(&gpio1->b2, 0, GPIO_OUTPUT);
>> > -       s5p_gpio_set_value(&gpio1->b2, 0, 1);
>> > -
>> > -       /* LCD power on */
>> > -       s5p_gpio_cfg_pin(&gpio1->x1, 5, GPIO_OUTPUT);
>> > -       s5p_gpio_set_value(&gpio1->x1, 5, 1);
>> > +       struct exynos5420_gpio_part2 *gpio2 =
>> > +               (struct exynos5420_gpio_part2
>> > *)samsung_get_base_gpio_part2();
>> >
>> >         /* Set Hotplug detect for DP */
>> > -       s5p_gpio_cfg_pin(&gpio1->x0, 7, GPIO_FUNC(0x3));
>> > +       s5p_gpio_cfg_pin(&gpio2->x0, 7, GPIO_FUNC(0x3));
>> >  }
>> >
>> > -vidinfo_t panel_info = {
>> > -       .vl_freq        = 60,
>> > -       .vl_col         = 2560,
>> > -       .vl_row         = 1600,
>> > -       .vl_width       = 2560,
>> > -       .vl_height      = 1600,
>> > -       .vl_clkp        = CONFIG_SYS_LOW,
>> > -       .vl_hsp         = CONFIG_SYS_LOW,
>> > -       .vl_vsp         = CONFIG_SYS_LOW,
>> > -       .vl_dp          = CONFIG_SYS_LOW,
>> > -       .vl_bpix        = 4,    /* LCD_BPP = 2^4, for output conosle on
>> > LCD */
>> > -
>> > -       /* wDP panel timing infomation */
>> > -       .vl_hspw        = 32,
>> > -       .vl_hbpd        = 80,
>> > -       .vl_hfpd        = 48,
>> > -
>> > -       .vl_vspw        = 6,
>> > -       .vl_vbpd        = 37,
>> > -       .vl_vfpd        = 3,
>> > -       .vl_cmd_allow_len = 0xf,
>> > -
>> > -       .win_id         = 3,
>> > -       .cfg_gpio       = cfg_lcd_gpio,
>> > -       .backlight_on   = NULL,
>> > -       .lcd_power_on   = NULL,
>> > -       .reset_lcd      = NULL,
>> > -       .dual_lcd_enabled = 0,
>> > -
>> > -       .init_delay     = 0,
>> > -       .power_on_delay = 0,
>> > -       .reset_delay    = 0,
>> > -       .interface_mode = FIMD_RGB_INTERFACE,
>> > -       .dp_enabled     = 1,
>> > -};
>> > -
>> > -static struct edp_device_info edp_info = {
>> > -       .disp_info = {
>> > -               .h_res = 2560,
>> > -               .h_sync_width = 32,
>> > -               .h_back_porch = 80,
>> > -               .h_front_porch = 48,
>> > -               .v_res = 1600,
>> > -               .v_sync_width  = 6,
>> > -               .v_back_porch = 37,
>> > -               .v_front_porch = 3,
>> > -               .v_sync_rate = 60,
>> > -       },
>> > -       .lt_info = {
>> > -               .lt_status = DP_LT_NONE,
>> > -       },
>> > -       .video_info = {
>> > -               .master_mode = 0,
>> > -               .bist_mode = DP_DISABLE,
>> > -               .bist_pattern = NO_PATTERN,
>> > -               .h_sync_polarity = 0,
>> > -               .v_sync_polarity = 0,
>> > -               .interlaced = 0,
>> > -               .color_space = COLOR_RGB,
>> > -               .dynamic_range = VESA,
>> > -               .ycbcr_coeff = COLOR_YCBCR601,
>> > -               .color_depth = COLOR_8,
>> > -       },
>> > -};
>> > -
>> > -static struct exynos_dp_platform_data dp_platform_data = {
>> > -       .phy_enable     = set_dp_phy_ctrl,
>> > -       .edp_dev_info   = &edp_info,
>> > -};
>> > -
>> > -void init_panel_info(vidinfo_t *vid)
>> > +void exynos_backlight_on(unsigned int onoff)
>> >  {
>> > -       vid->rgb_mode   = MODE_RGB_P,
>> > +       struct exynos5420_gpio_part1 *gpio1 =
>> > +               (struct exynos5420_gpio_part1
>> > *)samsung_get_base_gpio_part1();
>> > +
>> > +       struct exynos5420_gpio_part2 *gpio2 =
>> > +               (struct exynos5420_gpio_part2
>> > *)samsung_get_base_gpio_part2();
>> > +
>> > +       /* For PWM */
>> > +       s5p_gpio_cfg_pin(&gpio1->b2, 0, GPIO_OUTPUT);
>> > +       s5p_gpio_set_value(&gpio1->b2, 0, 1);
>>
>> Can we use generic GPIO calls instead? gpio_set_value(), etc
>
> I think GPIO numbering for exynos is yet to go in.
> Should wait till that goes in.

What is the hold-up on this? It was posted a very long time ago.

Regards,
Simon


More information about the U-Boot mailing list