[U-Boot] [PATCH 2/7 V3] mmc: Get secure erase information from card
Jaehoon Chung
jh80.chung at samsung.com
Fri Dec 27 12:13:10 CET 2013
Hi, Haijun.
On 12/10/2013 02:39 PM, Haijun Zhang wrote:
> Read command class from csd register and secure erase
> support bit from ext csd register. Also calculate the erase
> timeout and secure erase timeout.
>
> If read ext csd error, error status should be returned instead of
> give some incorrect information.
>
> Error log:
> =>
> => mmcinfo
> Device: FSL_SDHC
> Manufacturer ID: 0
> OEM: 0
> Name: Tran Speed: 0
> Rd Block Len: 0
> MMC version 0.0
> High Capacity: No
> Capacity: 0 Bytes
> Bus Width: 1-bit
> =>
>
> Signed-off-by: Haijun Zhang <haijun.zhang at freescale.com>
> ---
> changes for V3:
> - Change the erase group size to be block aligned.
>
> drivers/mmc/mmc.c | 52 ++++++++++++++++++++++++++++++++++++++--------------
> 1 file changed, 38 insertions(+), 14 deletions(-)
>
> diff --git a/drivers/mmc/mmc.c b/drivers/mmc/mmc.c
> index e1461a9..e8dbb8c 100644
> --- a/drivers/mmc/mmc.c
> +++ b/drivers/mmc/mmc.c
> @@ -871,6 +871,8 @@ static int mmc_startup(struct mmc *mmc)
> }
> }
>
> + mmc->cmdclass = cmd.response[1] >> 20;
> +
> /* divide frequency by 10, since the mults are 10x bigger */
> freq = fbase[(cmd.response[0] & 0x7)];
> mult = multipliers[((cmd.response[0] >> 3) & 0xf)];
> @@ -939,7 +941,8 @@ static int mmc_startup(struct mmc *mmc)
> capacity *= MMC_MAX_BLOCK_LEN;
> if ((capacity >> 20) > 2 * 1024)
> mmc->capacity_user = capacity;
> - }
> + } else
> + return COMM_ERR;
Well, I think this point need to consider more.
When error is returned, then this return is right. but it's also satisfied "ext_csd[EXT_CSD_REV] >= 2".
>
> switch (ext_csd[EXT_CSD_REV]) {
> case 1:
> @@ -960,6 +963,39 @@ static int mmc_startup(struct mmc *mmc)
> }
>
> /*
> + * The granularity of the erasable units is the Erase Group:The
> + * smallest number of consecutive write blocks which can be
> + * addressed for erase. The size of the Erase Group is card
> + * specific and stored in the CSD when ERASE_GROUP_DEF is
> + * disabled, and in the EXT_CSD when ERASE_GROUP_DEF is
> + * enabled.
> + */
> + if (ext_csd[EXT_CSD_ERASE_GROUP_DEF]) {
> + mmc->erase_grp_size =
> + ext_csd[EXT_CSD_HC_ERASE_GRP_SIZE] * 1024;
> +
> + mmc->erase_timeout_mult = 300 *
> + ext_csd[EXT_CSD_ERASE_TIMEOUT_MULT];
> + } else {
> + /* Calculate the group size from the csd value. */
> + int erase_gsz, erase_gmul;
> + erase_gsz = (mmc->csd[2] & 0x00007c00) >> 10;
> + erase_gmul = (mmc->csd[2] & 0x000003e0) >> 5;
> + mmc->erase_grp_size = (erase_gsz + 1)
> + * (erase_gmul + 1);
> + }
> +
> + if (ext_csd[EXT_CSD_REV] >= 4) {
> + mmc->sec_feature_support =
> + ext_csd[EXT_CSD_SEC_FEATURE_SUPPORT];
> + mmc->sec_erase_mult =
> + ext_csd[EXT_CSD_SEC_ERASE_MULT];
> + mmc->sec_erase_timeout = 300 *
> + ext_csd[EXT_CSD_SEC_ERASE_MULT] *
> + ext_csd[EXT_CSD_ERASE_TIMEOUT_MULT];
> + }
> +
> + /*
> * Host needs to enable ERASE_GRP_DEF bit if device is
> * partitioned. This bit will be lost every time after a reset
> * or power off. This will affect erase size.
> @@ -968,23 +1004,11 @@ static int mmc_startup(struct mmc *mmc)
> (ext_csd[EXT_CSD_PARTITIONS_ATTRIBUTE] & PART_ENH_ATTRIB)) {
> err = mmc_switch(mmc, EXT_CSD_CMD_SET_NORMAL,
> EXT_CSD_ERASE_GROUP_DEF, 1);
> -
> if (err)
> return err;
> -
> - /* Read out group size from ext_csd */
> - mmc->erase_grp_size =
> - ext_csd[EXT_CSD_HC_ERASE_GRP_SIZE] *
> - MMC_MAX_BLOCK_LEN * 1024;
> - } else {
> - /* Calculate the group size from the csd value. */
> - int erase_gsz, erase_gmul;
> - erase_gsz = (mmc->csd[2] & 0x00007c00) >> 10;
> - erase_gmul = (mmc->csd[2] & 0x000003e0) >> 5;
> - mmc->erase_grp_size = (erase_gsz + 1)
> - * (erase_gmul + 1);
> }
>
> +
remove the blank.
Best Regards,
Jaehoon Chung
> /* store the partition info of emmc */
> if ((ext_csd[EXT_CSD_PARTITIONING_SUPPORT] & PART_SUPPORT) ||
> ext_csd[EXT_CSD_BOOT_MULT])
>
More information about the U-Boot
mailing list