[U-Boot] [PATCH v4] powerpc/c29xpcie: add support for C29XPCIE board
Po Liu
Po.Liu at freescale.com
Wed Jul 3 10:38:14 CEST 2013
From: Mingkai Hu <Mingkai.Hu at freescale.com>
C29XPCIE board is a series of Freescale PCIe add-in cards to perform
as public key crypto accelerator or secure key management module. It
includes C293PCIE board, C293PCIE board and C291PCIE board.
- 512KB platform SRAM in addition to 512K L2 Cache/SRAM
- 512MB soldered DDR3 32bit memory
- CPLD System Logic
- 64MB x16 NOR flash and 4GB x8 NAND flash
- 16MB SPI flash
Signed-off-by: Mingkai Hu <Mingkai.Hu at freescale.com>
Singed-off-by: Po Liu <Po.Liu at freescale.com>
---
Base on the patch [PATCH 1/2 v3] powerpc/85xx: Add C29x SoC support
Changes for v2:
- Remove define CONFIG_C291/CONFIG_C292/CONFIG_C293,
replace with CONFIG_C29X
- Adjust the TLB config mode
- Add SEC node removal method by check the CPU SVR
- Clean up the C29XPCIE.h file
Changes for v3:
- Replace CONFIG_C29X with CONFIG_PPC_C29X
Changes for v4:
- Clean up comments in tlb.c
- Change NAND flash TLB and LAW size to 16KB
- Modify flash tlb mode in c29xpcie.c
- Change cpld.h and cpld.c code for read/write cpld register
- Continue clean up the C29XPCIE.h file
board/freescale/c29xpcie/Makefile | 34 +++
board/freescale/c29xpcie/c29xpcie.c | 151 ++++++++++++
board/freescale/c29xpcie/cpld.c | 134 ++++++++++
board/freescale/c29xpcie/cpld.h | 43 ++++
board/freescale/c29xpcie/ddr.c | 89 +++++++
board/freescale/c29xpcie/law.c | 22 ++
board/freescale/c29xpcie/tlb.c | 83 +++++++
boards.cfg | 2 +
include/configs/C29XPCIE.h | 475 ++++++++++++++++++++++++++++++++++++
9 files changed, 1033 insertions(+)
create mode 100644 board/freescale/c29xpcie/Makefile
create mode 100644 board/freescale/c29xpcie/c29xpcie.c
create mode 100644 board/freescale/c29xpcie/cpld.c
create mode 100644 board/freescale/c29xpcie/cpld.h
create mode 100644 board/freescale/c29xpcie/ddr.c
create mode 100644 board/freescale/c29xpcie/law.c
create mode 100644 board/freescale/c29xpcie/tlb.c
create mode 100644 include/configs/C29XPCIE.h
diff --git a/board/freescale/c29xpcie/Makefile b/board/freescale/c29xpcie/Makefile
new file mode 100644
index 0000000..15bef9a
--- /dev/null
+++ b/board/freescale/c29xpcie/Makefile
@@ -0,0 +1,34 @@
+#
+# Copyright 2013 Freescale Semiconductor, Inc.
+#
+# This program is free software; you can redistribute it and/or modify it
+# under the terms of the GNU General Public License as published by the Free
+# Software Foundation; either version 2 of the License, or (at your option)
+# any later version.
+#
+
+include $(TOPDIR)/config.mk
+
+LIB = $(obj)lib$(BOARD).o
+
+COBJS-y += $(BOARD).o
+COBJS-y += cpld.o
+COBJS-y += ddr.o
+COBJS-y += law.o
+COBJS-y += tlb.o
+
+SRCS := $(SOBJS:.o=.S) $(COBJS-y:.o=.c)
+OBJS := $(addprefix $(obj),$(COBJS-y))
+SOBJS := $(addprefix $(obj),$(SOBJS))
+
+$(LIB): $(obj).depend $(OBJS) $(SOBJS)
+ $(call cmd_link_o_target, $(OBJS))
+
+#########################################################################
+
+# defines $(obj).depend target
+include $(SRCTREE)/rules.mk
+
+sinclude $(obj).depend
+
+#########################################################################
diff --git a/board/freescale/c29xpcie/c29xpcie.c b/board/freescale/c29xpcie/c29xpcie.c
new file mode 100644
index 0000000..acc59d2
--- /dev/null
+++ b/board/freescale/c29xpcie/c29xpcie.c
@@ -0,0 +1,151 @@
+/*
+ * Copyright 2013 Freescale Semiconductor, Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the Free
+ * Software Foundation; either version 2 of the License, or (at your option)
+ * any later version.
+ */
+
+#include <common.h>
+#include <asm/processor.h>
+#include <asm/mmu.h>
+#include <asm/cache.h>
+#include <asm/immap_85xx.h>
+#include <asm/io.h>
+#include <miiphy.h>
+#include <libfdt.h>
+#include <fdt_support.h>
+#include <fsl_mdio.h>
+#include <tsec.h>
+#include <mmc.h>
+#include <netdev.h>
+#include <pci.h>
+#include <asm/fsl_ifc.h>
+#include <asm/fsl_pci.h>
+
+#include "cpld.h"
+
+DECLARE_GLOBAL_DATA_PTR;
+
+int checkboard(void)
+{
+ struct cpu_type *cpu = gd->arch.cpu;
+ struct cpld_data *cpld_data = (void *)(CONFIG_SYS_CPLD_BASE);
+
+ printf("Board: %sPCIe, ", cpu->name);
+ printf("CPLD Ver: 0x%02x\n", in_8(&cpld_data->cpldver));
+
+ return 0;
+}
+
+int board_early_init_f(void)
+{
+ struct fsl_ifc *ifc = (void *)CONFIG_SYS_IFC_ADDR;
+
+ /* Clock configuration to access CPLD using IFC(GPCM) */
+ setbits_be32(&ifc->ifc_gcr, 1 << IFC_GCR_TBCTL_TRN_TIME_SHIFT);
+
+ return 0;
+}
+
+int board_early_init_r(void)
+{
+ const unsigned long flashbase = CONFIG_SYS_FLASH_BASE;
+ const u8 flash_esel = find_tlb_idx((void *)flashbase, 1);
+
+ /*
+ * Remap Boot flash region to caching-inhibited
+ * so that flash can be erased properly.
+ */
+
+ /* Flush d-cache and invalidate i-cache of any FLASH data */
+ flush_dcache();
+ invalidate_icache();
+
+ /* invalidate existing TLB entry for flash */
+ disable_tlb(flash_esel);
+
+ set_tlb(1, flashbase, CONFIG_SYS_FLASH_BASE_PHYS,
+ MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+ 0, flash_esel, BOOKE_PAGESZ_64M, 1);
+
+ return 0;
+}
+
+#ifdef CONFIG_PCI
+void pci_init_board(void)
+{
+ fsl_pcie_init_board(0);
+}
+#endif /* ifdef CONFIG_PCI */
+
+#ifdef CONFIG_TSEC_ENET
+int board_eth_init(bd_t *bis)
+{
+ struct fsl_pq_mdio_info mdio_info;
+ struct tsec_info_struct tsec_info[2];
+ int num = 0;
+
+#ifdef CONFIG_TSEC1
+ SET_STD_TSEC_INFO(tsec_info[num], 1);
+ num++;
+#endif
+#ifdef CONFIG_TSEC2
+ SET_STD_TSEC_INFO(tsec_info[num], 2);
+ num++;
+#endif
+ if (!num) {
+ printf("No TSECs initialized\n");
+ return 0;
+ }
+
+ /* Register 1G MDIO bus */
+ mdio_info.regs = (struct tsec_mii_mng *)CONFIG_SYS_MDIO_BASE_ADDR;
+ mdio_info.name = DEFAULT_MII_NAME;
+
+ fsl_pq_mdio_init(bis, &mdio_info);
+
+ tsec_eth_init(bis, tsec_info, num);
+
+ return pci_eth_init(bis);
+}
+#endif
+
+#if defined(CONFIG_OF_BOARD_SETUP)
+void fdt_del_sec(void *blob, int offset)
+{
+ int nodeoff = 0;
+
+ while ((nodeoff = fdt_node_offset_by_compat_reg(blob, "fsl,sec-v6.0",
+ CONFIG_SYS_CCSRBAR_PHYS + CONFIG_SYS_FSL_SEC_OFFSET
+ + offset * 0x20000)) >= 0) {
+ fdt_del_node(blob, nodeoff);
+ offset++;
+ }
+}
+
+void ft_board_setup(void *blob, bd_t *bd)
+{
+ phys_addr_t base;
+ phys_size_t size;
+ struct cpu_type *cpu;
+
+ cpu = gd->arch.cpu;
+
+ ft_cpu_setup(blob, bd);
+
+ base = getenv_bootm_low();
+ size = getenv_bootm_size();
+
+#if defined(CONFIG_PCI)
+ FT_FSL_PCI_SETUP;
+#endif
+
+ fdt_fixup_memory(blob, (u64)base, (u64)size);
+ if (cpu->soc_ver == SVR_C291)
+ fdt_del_sec(blob, 1);
+ else if (cpu->soc_ver == SVR_C292)
+ fdt_del_sec(blob, 2);
+}
+#endif
diff --git a/board/freescale/c29xpcie/cpld.c b/board/freescale/c29xpcie/cpld.c
new file mode 100644
index 0000000..b17a7ba
--- /dev/null
+++ b/board/freescale/c29xpcie/cpld.c
@@ -0,0 +1,134 @@
+/**
+ * Copyright 2013 Freescale Semiconductor
+ * Author: Mingkai Hu <Mingkai.hu at freescale.com>
+ * Po Liu <Po.Liu at freescale.com>
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the Free
+ * Software Foundation; either version 2 of the License, or (at your option)
+ * any later version.
+ *
+ * This file provides support for the board-specific CPLD used on some Freescale
+ * reference boards.
+ *
+ * The following macros need to be defined:
+ *
+ * CONFIG_SYS_CPLD_BASE - The virtual address of the base of the
+ * CPLD register map
+ *
+ */
+
+#include <common.h>
+#include <command.h>
+#include <asm/io.h>
+
+#include "cpld.h"
+/**
+ * Set the boot bank to the alternate bank
+ */
+void cpld_set_altbank(u8 banksel)
+{
+ struct cpld_data *cpld_data = (void *)(CONFIG_SYS_CPLD_BASE);
+ u8 reg11;
+
+ reg11 = in_8(&cpld_data->flhcsr);
+
+ switch (banksel) {
+ case 1:
+ out_8(&cpld_data->flhcsr, (reg11 & CPLD_BANKSEL_MASK)
+ | CPLD_BANKSEL_EN | CPLD_SELECT_BANK1);
+ break;
+ case 2:
+ out_8(&cpld_data->flhcsr, (reg11 & CPLD_BANKSEL_MASK)
+ | CPLD_BANKSEL_EN | CPLD_SELECT_BANK2);
+ break;
+ case 3:
+ out_8(&cpld_data->flhcsr, (reg11 & CPLD_BANKSEL_MASK)
+ | CPLD_BANKSEL_EN | CPLD_SELECT_BANK3);
+ break;
+ case 4:
+ out_8(&cpld_data->flhcsr, (reg11 & CPLD_BANKSEL_MASK)
+ | CPLD_BANKSEL_EN | CPLD_SELECT_BANK4);
+ break;
+ default:
+ printf("Invalid value! [1-4]\n");
+ return;
+ }
+
+ udelay(100);
+ do_reset(NULL, 0, 0, NULL);
+}
+
+/**
+ * Set the boot bank to the default bank
+ */
+void cpld_set_defbank(void)
+{
+ cpld_set_altbank(4);
+}
+
+#ifdef DEBUG
+static void cpld_dump_regs(void)
+{
+ struct cpld_data *cpld_data = (void *)(CONFIG_SYS_CPLD_BASE);
+
+ printf("chipid1 = 0x%02x\n", in_8(&cpld_data->chipid1));
+ printf("chipid2 = 0x%02x\n", in_8(&cpld_data->chipid2));
+ printf("hwver = 0x%02x\n", in_8(&cpld_data->hwver));
+ printf("cpldver = 0x%02x\n", in_8(&cpld_data->cpldver));
+ printf("rstcon = 0x%02x\n", in_8(&cpld_data->rstcon));
+ printf("flhcsr = 0x%02x\n", in_8(&cpld_data->flhcsr));
+ printf("wdcsr = 0x%02x\n", in_8(&cpld_data->wdcsr));
+ printf("wdkick = 0x%02x\n", in_8(&cpld_data->wdkick));
+ printf("fancsr = 0x%02x\n", in_8(&cpld_data->fancsr));
+ printf("ledcsr = 0x%02x\n", in_8(&cpld_data->ledcsr));
+ printf("misc = 0x%02x\n", in_8(&cpld_data->misccsr));
+ printf("bootor = 0x%02x\n", in_8(&cpld_data->bootor));
+ printf("bootcfg1 = 0x%02x\n", in_8(&cpld_data->bootcfg1));
+ printf("bootcfg2 = 0x%02x\n", in_8(&cpld_data->bootcfg2));
+ printf("bootcfg3 = 0x%02x\n", in_8(&cpld_data->bootcfg3));
+ printf("bootcfg4 = 0x%02x\n", in_8(&cpld_data->bootcfg4));
+ putc('\n');
+}
+#endif
+
+int cpld_cmd(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[])
+{
+ int rc = 0;
+ unsigned char value;
+
+ if (argc <= 1)
+ return cmd_usage(cmdtp);
+
+ if (strcmp(argv[1], "reset") == 0) {
+ if (!strcmp(argv[2], "altbank") && argv[3]) {
+ value = (u8)simple_strtoul(argv[3], NULL, 16);
+ cpld_set_altbank(value);
+ } else if (!argv[2])
+ cpld_set_defbank();
+ else
+ cmd_usage(cmdtp);
+#ifdef DEBUG
+ } else if (strcmp(argv[1], "dump") == 0) {
+ cpld_dump_regs();
+#endif
+ } else
+ rc = cmd_usage(cmdtp);
+
+ return rc;
+}
+
+U_BOOT_CMD(
+ cpld_cmd, CONFIG_SYS_MAXARGS, 1, cpld_cmd,
+ "Reset the board using the CPLD sequencer",
+ "reset - hard reset to default bank 4\n"
+ "cpld_cmd reset altbank [bank]- reset to alternate bank\n"
+ " - [bank] bank value select 1-4\n"
+ " - bank 1 on the flash 0x0000000~0x0ffffff\n"
+ " - bank 2 on the flash 0x1000000~0x1ffffff\n"
+ " - bank 3 on the flash 0x2000000~0x2ffffff\n"
+ " - bank 4 on the flash 0x3000000~0x3ffffff\n"
+#ifdef DEBUG
+ "cpld_cmd dump - display the CPLD registers\n"
+#endif
+ );
diff --git a/board/freescale/c29xpcie/cpld.h b/board/freescale/c29xpcie/cpld.h
new file mode 100644
index 0000000..24093c4
--- /dev/null
+++ b/board/freescale/c29xpcie/cpld.h
@@ -0,0 +1,43 @@
+/**
+ * Copyright 2013 Freescale Semiconductor
+ * Author: Mingkai Hu <Mingkai.Hu at freescale.com>
+ * Po Liu <Po.Liu at freescale.com>
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the Free
+ * Software Foundation; either version 2 of the License, or (at your option)
+ * any later version.
+ *
+ * This file provides support for the ngPIXIS, a board-specific FPGA used on
+ * some Freescale reference boards.
+ */
+
+/*
+ * CPLD register set. Feel free to add board-specific #ifdefs where necessary.
+ */
+struct cpld_data {
+ u8 chipid1; /* 0x0 - CPLD Chip ID1 Register */
+ u8 chipid2; /* 0x1 - CPLD Chip ID2 Register */
+ u8 hwver; /* 0x2 - Hardware Version Register */
+ u8 cpldver; /* 0x3 - Software Version Register */
+ u8 res[12];
+ u8 rstcon; /* 0x10 - Reset control register */
+ u8 flhcsr; /* 0x11 - Flash control and status Register */
+ u8 wdcsr; /* 0x12 - Watchdog control and status Register */
+ u8 wdkick; /* 0x13 - Watchdog kick Register */
+ u8 fancsr; /* 0x14 - Fan control and status Register */
+ u8 ledcsr; /* 0x15 - LED control and status Register */
+ u8 misccsr; /* 0x16 - Misc control and status Register */
+ u8 bootor; /* 0x17 - Boot configure override Register */
+ u8 bootcfg1; /* 0x18 - Boot configure 1 Register */
+ u8 bootcfg2; /* 0x19 - Boot configure 2 Register */
+ u8 bootcfg3; /* 0x1a - Boot configure 3 Register */
+ u8 bootcfg4; /* 0x1b - Boot configure 4 Register */
+};
+
+#define CPLD_BANKSEL_EN 0x02
+#define CPLD_BANKSEL_MASK 0x3f
+#define CPLD_SELECT_BANK1 0xc0
+#define CPLD_SELECT_BANK2 0x80
+#define CPLD_SELECT_BANK3 0x40
+#define CPLD_SELECT_BANK4 0x00
diff --git a/board/freescale/c29xpcie/ddr.c b/board/freescale/c29xpcie/ddr.c
new file mode 100644
index 0000000..62476ca
--- /dev/null
+++ b/board/freescale/c29xpcie/ddr.c
@@ -0,0 +1,89 @@
+/*
+ * Copyright 2013 Freescale Semiconductor, Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the Free
+ * Software Foundation; either version 2 of the License, or (at your option)
+ * any later version.
+ */
+
+#include <common.h>
+#include <asm/fsl_law.h>
+#include <asm/fsl_ddr_sdram.h>
+#include <asm/fsl_ddr_dimm_params.h>
+
+/*
+ * Micron MT41J128M16HA-15E
+ * */
+dimm_params_t ddr_raw_timing = {
+ .n_ranks = 1,
+ .rank_density = 536870912u,
+ .capacity = 536870912u,
+ .primary_sdram_width = 32,
+ .ec_sdram_width = 8,
+ .registered_dimm = 0,
+ .mirrored_dimm = 0,
+ .n_row_addr = 14,
+ .n_col_addr = 10,
+ .n_banks_per_sdram_device = 8,
+ .edc_config = 2,
+ .burst_lengths_bitmask = 0x0c,
+
+ .tCKmin_X_ps = 1650,
+ .caslat_X = 0x7e << 4, /* 5,6,7,8,9,10 */
+ .tAA_ps = 14050,
+ .tWR_ps = 15000,
+ .tRCD_ps = 13500,
+ .tRRD_ps = 75000,
+ .tRP_ps = 13500,
+ .tRAS_ps = 40000,
+ .tRC_ps = 49500,
+ .tRFC_ps = 160000,
+ .tWTR_ps = 75000,
+ .tRTP_ps = 75000,
+ .refresh_rate_ps = 7800000,
+ .tFAW_ps = 30000,
+};
+
+int fsl_ddr_get_dimm_params(dimm_params_t *pdimm,
+ unsigned int controller_number,
+ unsigned int dimm_number)
+{
+ const char dimm_model[] = "Fixed DDR on board";
+
+ if ((controller_number == 0) && (dimm_number == 0)) {
+ memcpy(pdimm, &ddr_raw_timing, sizeof(dimm_params_t));
+ memset(pdimm->mpart, 0, sizeof(pdimm->mpart));
+ memcpy(pdimm->mpart, dimm_model, sizeof(dimm_model) - 1);
+ }
+
+ return 0;
+}
+
+void fsl_ddr_board_options(memctl_options_t *popts,
+ dimm_params_t *pdimm,
+ unsigned int ctrl_num)
+{
+ int i;
+ popts->clk_adjust = 2;
+ popts->cpo_override = 0x1f;
+ popts->write_data_delay = 4;
+ popts->half_strength_driver_enable = 1;
+ popts->bstopre = 0x3cf;
+ popts->quad_rank_present = 1;
+ popts->rtt_override = 1;
+ popts->rtt_override_value = 1;
+ popts->dynamic_power = 1;
+ /* Write leveling override */
+ popts->wrlvl_en = 1;
+ popts->wrlvl_override = 1;
+ popts->wrlvl_sample = 0xf;
+ popts->wrlvl_start = 0x4;
+ popts->trwt_override = 1;
+ popts->trwt = 0;
+
+ for (i = 0; i < CONFIG_CHIP_SELECTS_PER_CTRL; i++) {
+ popts->cs_local_opts[i].odt_rd_cfg = FSL_DDR_ODT_NEVER;
+ popts->cs_local_opts[i].odt_wr_cfg = FSL_DDR_ODT_CS;
+ }
+}
diff --git a/board/freescale/c29xpcie/law.c b/board/freescale/c29xpcie/law.c
new file mode 100644
index 0000000..10a2fbf
--- /dev/null
+++ b/board/freescale/c29xpcie/law.c
@@ -0,0 +1,22 @@
+/*
+ * Copyright 2013 Freescale Semiconductor, Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the Free
+ * Software Foundation; either version 2 of the License, or (at your option)
+ * any later version.
+ */
+
+#include <common.h>
+#include <asm/fsl_law.h>
+#include <asm/mmu.h>
+
+struct law_entry law_table[] = {
+ SET_LAW(CONFIG_SYS_FLASH_BASE_PHYS, LAW_SIZE_64M, LAW_TRGT_IF_IFC),
+ SET_LAW(CONFIG_SYS_CPLD_BASE_PHYS, LAW_SIZE_4K, LAW_TRGT_IF_IFC),
+ SET_LAW(CONFIG_SYS_NAND_BASE_PHYS, LAW_SIZE_16K, LAW_TRGT_IF_IFC),
+ SET_LAW(CONFIG_SYS_PLATFORM_SRAM_BASE_PHYS, LAW_SIZE_512K,
+ LAW_TRGT_IF_PLATFORM_SRAM),
+};
+
+int num_law_entries = ARRAY_SIZE(law_table);
diff --git a/board/freescale/c29xpcie/tlb.c b/board/freescale/c29xpcie/tlb.c
new file mode 100644
index 0000000..88ca172
--- /dev/null
+++ b/board/freescale/c29xpcie/tlb.c
@@ -0,0 +1,83 @@
+/*
+ * Copyright 2013 Freescale Semiconductor, Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the Free
+ * Software Foundation; either version 2 of the License, or (at your option)
+ * any later version.
+ */
+
+#include <common.h>
+#include <asm/mmu.h>
+
+struct fsl_e_tlb_entry tlb_table[] = {
+ /* TLB 0 - for temp stack in cache */
+ SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR, CONFIG_SYS_INIT_RAM_ADDR,
+ MAS3_SX|MAS3_SW|MAS3_SR, 0,
+ 0, 0, BOOKE_PAGESZ_4K, 0),
+ SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 4 * 1024 ,
+ CONFIG_SYS_INIT_RAM_ADDR + 4 * 1024,
+ MAS3_SX|MAS3_SW|MAS3_SR, 0,
+ 0, 0, BOOKE_PAGESZ_4K, 0),
+ SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 8 * 1024 ,
+ CONFIG_SYS_INIT_RAM_ADDR + 8 * 1024,
+ MAS3_SX|MAS3_SW|MAS3_SR, 0,
+ 0, 0, BOOKE_PAGESZ_4K, 0),
+ SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 12 * 1024 ,
+ CONFIG_SYS_INIT_RAM_ADDR + 12 * 1024,
+ MAS3_SX|MAS3_SW|MAS3_SR, 0,
+ 0, 0, BOOKE_PAGESZ_4K, 0),
+
+ /* TLB 1 */
+ SET_TLB_ENTRY(1, 0xfffff000, 0xfffff000,
+ MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+ 0, 0, BOOKE_PAGESZ_4K, 1),
+
+ SET_TLB_ENTRY(1, CONFIG_SYS_CCSRBAR, CONFIG_SYS_CCSRBAR_PHYS,
+ MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+ 0, 1, BOOKE_PAGESZ_1M, 1),
+
+ SET_TLB_ENTRY(1, CONFIG_SYS_FLASH_BASE, CONFIG_SYS_FLASH_BASE_PHYS,
+ MAS3_SX|MAS3_SR, MAS2_W|MAS2_G,
+ 0, 2, BOOKE_PAGESZ_64M, 1),
+
+#ifdef CONFIG_PCI
+ SET_TLB_ENTRY(1, CONFIG_SYS_PCIE1_MEM_VIRT, CONFIG_SYS_PCIE1_MEM_PHYS,
+ MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+ 0, 3, BOOKE_PAGESZ_256M, 1),
+
+ SET_TLB_ENTRY(1, CONFIG_SYS_PCIE1_IO_VIRT, CONFIG_SYS_PCIE1_IO_PHYS,
+ MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+ 0, 4, BOOKE_PAGESZ_256K, 1),
+#endif
+
+ SET_TLB_ENTRY(1, CONFIG_SYS_CPLD_BASE, CONFIG_SYS_CPLD_BASE_PHYS,
+ MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+ 0, 5, BOOKE_PAGESZ_4K, 1),
+
+ SET_TLB_ENTRY(1, CONFIG_SYS_NAND_BASE, CONFIG_SYS_NAND_BASE_PHYS,
+ MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+ 0, 6, BOOKE_PAGESZ_16K, 1),
+
+ SET_TLB_ENTRY(1, CONFIG_SYS_PLATFORM_SRAM_BASE,
+ CONFIG_SYS_PLATFORM_SRAM_BASE_PHYS,
+ MAS3_SX|MAS3_SW|MAS3_SR, 0,
+ 0, 7, BOOKE_PAGESZ_256K, 1),
+ SET_TLB_ENTRY(1, CONFIG_SYS_PLATFORM_SRAM_BASE + 0x40000,
+ CONFIG_SYS_PLATFORM_SRAM_BASE_PHYS + 0x40000,
+ MAS3_SX|MAS3_SW|MAS3_SR, 0,
+ 0, 8, BOOKE_PAGESZ_256K, 1),
+
+#ifdef CONFIG_SYS_RAMBOOT
+ SET_TLB_ENTRY(1, CONFIG_SYS_DDR_SDRAM_BASE,
+ CONFIG_SYS_DDR_SDRAM_BASE,
+ MAS3_SX|MAS3_SW|MAS3_SR, 0,
+ 0, 9, BOOKE_PAGESZ_256M, 1),
+ SET_TLB_ENTRY(1, CONFIG_SYS_DDR_SDRAM_BASE + 0x10000000,
+ CONFIG_SYS_DDR_SDRAM_BASE + 0x10000000,
+ MAS3_SX|MAS3_SW|MAS3_SR, 0,
+ 0, 10, BOOKE_PAGESZ_256M, 1),
+#endif
+};
+
+int num_tlb_entries = ARRAY_SIZE(tlb_table);
diff --git a/boards.cfg b/boards.cfg
index c0c4282..4c68e9f 100644
--- a/boards.cfg
+++ b/boards.cfg
@@ -771,6 +771,8 @@ MPC8569MDS_NAND powerpc mpc85xx mpc8569mds freesca
MPC8572DS powerpc mpc85xx mpc8572ds freescale - MPC8572DS
MPC8572DS_36BIT powerpc mpc85xx mpc8572ds freescale - MPC8572DS:36BIT
MPC8572DS_NAND powerpc mpc85xx mpc8572ds freescale - MPC8572DS:NAND
+C29XPCIE powerpc mpc85xx c29xpcie freescale - C29XPCIE:C29XPCIE,36BIT
+C29XPCIE_SPIFLASH powerpc mpc85xx c29xpcie freescale - C29XPCIE:C29XPCIE,36BIT,SPIFLASH
P1010RDB_36BIT_NAND powerpc mpc85xx p1010rdb freescale - P1010RDB:P1010RDB,36BIT,NAND
P1010RDB_36BIT_NAND_SECBOOT powerpc mpc85xx p1010rdb freescale - P1010RDB:P1010RDB,36BIT,NAND_SECBOOT,SECURE_BOOT
P1010RDB_36BIT_NOR powerpc mpc85xx p1010rdb freescale - P1010RDB:P1010RDB,36BIT
diff --git a/include/configs/C29XPCIE.h b/include/configs/C29XPCIE.h
new file mode 100644
index 0000000..7d56128
--- /dev/null
+++ b/include/configs/C29XPCIE.h
@@ -0,0 +1,475 @@
+/*
+ * Copyright 2013 Freescale Semiconductor, Inc.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+/*
+ * C29XPCIE board configuration file
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+#define CONFIG_PHYS_64BIT
+
+#ifdef CONFIG_C29XPCIE
+#define CONFIG_PPC_C29X
+#endif
+
+#ifdef CONFIG_SPIFLASH
+#define CONFIG_RAMBOOT_SPIFLASH
+#define CONFIG_SYS_TEXT_BASE 0x11000000
+#define CONFIG_RESET_VECTOR_ADDRESS 0x1107fffc
+#endif
+
+#ifndef CONFIG_SYS_TEXT_BASE
+#define CONFIG_SYS_TEXT_BASE 0xeff80000
+#endif
+
+#ifndef CONFIG_RESET_VECTOR_ADDRESS
+#define CONFIG_RESET_VECTOR_ADDRESS 0xeffffffc
+#endif
+
+#ifndef CONFIG_SYS_MONITOR_BASE
+#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE
+#endif
+
+/* High Level Configuration Options */
+#define CONFIG_BOOKE /* BOOKE */
+#define CONFIG_E500 /* BOOKE e500 family */
+#define CONFIG_MPC85xx
+#define CONFIG_FSL_IFC /* Enable IFC Support */
+#define CONFIG_SYS_HAS_SERDES /* common SERDES init code */
+
+#define CONFIG_PCI /* Enable PCI/PCIE */
+#ifdef CONFIG_PCI
+#define CONFIG_PCIE1 /* PCIE controler 1 (slot 1) */
+#define CONFIG_FSL_PCI_INIT /* Use common FSL init code */
+#define CONFIG_PCI_INDIRECT_BRIDGE
+#define CONFIG_FSL_PCIE_RESET /* need PCIe reset errata */
+#define CONFIG_SYS_PCI_64BIT /* enable 64-bit PCI resources */
+
+#define CONFIG_CMD_NET
+#define CONFIG_CMD_PCI
+
+#define CONFIG_E1000
+
+/*
+ * PCI Windows
+ * Memory space is mapped 1-1, but I/O space must start from 0.
+ */
+/* controller 1, Slot 1, tgtid 1, Base address a000 */
+#define CONFIG_SYS_PCIE1_NAME "Slot 1"
+#define CONFIG_SYS_PCIE1_MEM_VIRT 0x80000000
+#define CONFIG_SYS_PCIE1_MEM_BUS 0x80000000
+#define CONFIG_SYS_PCIE1_MEM_PHYS 0xc00000000ull
+#define CONFIG_SYS_PCIE1_MEM_SIZE 0x10000000 /* 256M */
+#define CONFIG_SYS_PCIE1_IO_VIRT 0xffc00000
+#define CONFIG_SYS_PCIE1_IO_BUS 0x00000000
+#define CONFIG_SYS_PCIE1_IO_SIZE 0x00010000 /* 64k */
+#define CONFIG_SYS_PCIE1_IO_PHYS 0xfffc00000ull
+
+#define CONFIG_PCI_PNP /* do pci plug-and-play */
+
+#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
+#define CONFIG_DOS_PARTITION
+#endif
+
+#define CONFIG_FSL_LAW /* Use common FSL init code */
+#define CONFIG_TSEC_ENET
+#define CONFIG_ENV_OVERWRITE
+
+#define CONFIG_DDR_CLK_FREQ 100000000
+#define CONFIG_SYS_CLK_FREQ 66666666
+
+#define CONFIG_HWCONFIG
+
+/*
+ * These can be toggled for performance analysis, otherwise use default.
+ */
+#define CONFIG_L2_CACHE /* toggle L2 cache */
+#define CONFIG_BTB /* toggle branch predition */
+
+#define CONFIG_ADDR_STREAMING /* toggle addr streaming */
+
+#define CONFIG_ENABLE_36BIT_PHYS
+
+#define CONFIG_ADDR_MAP 1
+#define CONFIG_SYS_NUM_ADDR_MAP 16 /* number of TLB1 entries */
+
+#define CONFIG_SYS_MEMTEST_START 0x00200000
+#define CONFIG_SYS_MEMTEST_END 0x00400000
+#define CONFIG_PANIC_HANG
+
+/* DDR Setup */
+#define CONFIG_FSL_DDR3
+#define CONFIG_DDR_SPD
+#define CONFIG_SYS_SPD_BUS_NUM 0
+#define SPD_EEPROM_ADDRESS 0x50
+#define CONFIG_SYS_DDR_RAW_TIMING
+
+/* DDR ECC Setup*/
+#define CONFIG_DDR_ECC
+#define CONFIG_MEM_INIT_VALUE 0xDeadBeef
+#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER
+
+#define CONFIG_SYS_SDRAM_SIZE 512
+#define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000
+#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE
+
+#define CONFIG_DIMM_SLOTS_PER_CTLR 1
+#define CONFIG_CHIP_SELECTS_PER_CTRL 1
+
+#define CONFIG_SYS_CCSRBAR 0xffe00000
+#define CONFIG_SYS_CCSRBAR_PHYS_LOW CONFIG_SYS_CCSRBAR
+
+/* Platform SRAM setting */
+#define CONFIG_SYS_PLATFORM_SRAM_BASE 0xffb00000
+#define CONFIG_SYS_PLATFORM_SRAM_BASE_PHYS \
+ (0xf00000000ull | CONFIG_SYS_PLATFORM_SRAM_BASE)
+#define CONFIG_SYS_PLATFORM_SRAM_SIZE (512 << 10)
+
+/*
+ * IFC Definitions
+ */
+/* NOR Flash on IFC */
+#define CONFIG_SYS_FLASH_BASE 0xec000000
+#define CONFIG_SYS_MAX_FLASH_SECT 512 /* 64M */
+
+#define CONFIG_SYS_FLASH_BASE_PHYS (0xf00000000ull | CONFIG_SYS_FLASH_BASE)
+
+#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE_PHYS }
+#define CONFIG_SYS_MAX_FLASH_BANKS 1
+
+#define CONFIG_SYS_FLASH_QUIET_TEST
+#define CONFIG_FLASH_SHOW_PROGRESS 45
+#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* in ms */
+#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* in ms */
+
+/* 16Bit NOR Flash - S29GL512S10TFI01 */
+#define CONFIG_SYS_NOR_CSPR (CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) | \
+ CSPR_PORT_SIZE_16 | \
+ CSPR_MSEL_NOR | \
+ CSPR_V)
+#define CONFIG_SYS_NOR_AMASK IFC_AMASK(64*1024*1024)
+#define CONFIG_SYS_NOR_CSOR CSOR_NOR_ADM_SHIFT(4)
+#define CONFIG_SYS_NOR_FTIM0 (FTIM0_NOR_TACSE(0x4) | \
+ FTIM0_NOR_TEADC(0x5) | \
+ FTIM0_NOR_TEAHC(0x5))
+#define CONFIG_SYS_NOR_FTIM1 (FTIM1_NOR_TACO(0x1e) | \
+ FTIM1_NOR_TRAD_NOR(0x0f) | \
+ FTIM1_NOR_TSEQRAD_NOR(0x0f))
+#define CONFIG_SYS_NOR_FTIM2 (FTIM2_NOR_TCS(0x4) | \
+ FTIM2_NOR_TCH(0x4) | \
+ FTIM2_NOR_TWP(0x1c))
+#define CONFIG_SYS_NOR_FTIM3 0x0
+
+/* CFI for NOR Flash */
+#define CONFIG_FLASH_CFI_DRIVER
+#define CONFIG_SYS_FLASH_CFI
+#define CONFIG_SYS_FLASH_EMPTY_INFO
+#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE
+
+/* NAND Flash on IFC */
+#define CONFIG_NAND_FSL_IFC
+#define CONFIG_SYS_NAND_BASE 0xff800000
+#define CONFIG_SYS_NAND_BASE_PHYS 0xfff800000ull
+
+#define CONFIG_SYS_NAND_BASE_LIST { CONFIG_SYS_NAND_BASE }
+
+#define CONFIG_SYS_MAX_NAND_DEVICE 1
+#define CONFIG_MTD_NAND_VERIFY_WRITE
+#define CONFIG_CMD_NAND
+#define CONFIG_SYS_NAND_BLOCK_SIZE (128 * 1024)
+
+/* 8Bit NAND Flash - K9F1G08U0B */
+#define CONFIG_SYS_NAND_CSPR (CSPR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \
+ | CSPR_PORT_SIZE_8 \
+ | CSPR_MSEL_NAND \
+ | CSPR_V)
+#define CONFIG_SYS_NAND_AMASK IFC_AMASK(64*1024)
+#define CONFIG_SYS_NAND_CSOR (CSOR_NAND_ECC_ENC_EN /* ECC on encode */ \
+ | CSOR_NAND_ECC_DEC_EN /* ECC on decode */ \
+ | CSOR_NAND_ECC_MODE_4 /* 4-bit ECC */ \
+ | CSOR_NAND_RAL_2 /* RAL = 2 Bytes */ \
+ | CSOR_NAND_PGS_2K /* Page Size = 2k */ \
+ | CSOR_NAND_SPRZ_64 /* Spare size = 64 */ \
+ | CSOR_NAND_PB(64)) /* 64 Pages Per Block */
+#define CONFIG_SYS_NAND_FTIM0 (FTIM0_NAND_TCCST(0x01) | \
+ FTIM0_NAND_TWP(0x0c) | \
+ FTIM0_NAND_TWCHT(0x08) | \
+ FTIM0_NAND_TWH(0x06))
+#define CONFIG_SYS_NAND_FTIM1 (FTIM1_NAND_TADLE(0x28) | \
+ FTIM1_NAND_TWBE(0x1d) | \
+ FTIM1_NAND_TRR(0x08) | \
+ FTIM1_NAND_TRP(0x0c))
+#define CONFIG_SYS_NAND_FTIM2 (FTIM2_NAND_TRAD(0x0c) | \
+ FTIM2_NAND_TREH(0x0a) | \
+ FTIM2_NAND_TWHRE(0x18))
+#define CONFIG_SYS_NAND_FTIM3 (FTIM3_NAND_TWW(0x04))
+
+#define CONFIG_SYS_NAND_DDR_LAW 11
+
+/* Set up IFC registers for boot location NOR/NAND */
+#define CONFIG_SYS_CSPR0 CONFIG_SYS_NOR_CSPR
+#define CONFIG_SYS_AMASK0 CONFIG_SYS_NOR_AMASK
+#define CONFIG_SYS_CSOR0 CONFIG_SYS_NOR_CSOR
+#define CONFIG_SYS_CS0_FTIM0 CONFIG_SYS_NOR_FTIM0
+#define CONFIG_SYS_CS0_FTIM1 CONFIG_SYS_NOR_FTIM1
+#define CONFIG_SYS_CS0_FTIM2 CONFIG_SYS_NOR_FTIM2
+#define CONFIG_SYS_CS0_FTIM3 CONFIG_SYS_NOR_FTIM3
+#define CONFIG_SYS_CSPR1 CONFIG_SYS_NAND_CSPR
+#define CONFIG_SYS_AMASK1 CONFIG_SYS_NAND_AMASK
+#define CONFIG_SYS_CSOR1 CONFIG_SYS_NAND_CSOR
+#define CONFIG_SYS_CS1_FTIM0 CONFIG_SYS_NAND_FTIM0
+#define CONFIG_SYS_CS1_FTIM1 CONFIG_SYS_NAND_FTIM1
+#define CONFIG_SYS_CS1_FTIM2 CONFIG_SYS_NAND_FTIM2
+#define CONFIG_SYS_CS1_FTIM3 CONFIG_SYS_NAND_FTIM3
+
+/* CPLD on IFC, selected by CS2 */
+#define CONFIG_SYS_CPLD_BASE 0xffdf0000
+#define CONFIG_SYS_CPLD_BASE_PHYS (0xf00000000ull \
+ | CONFIG_SYS_CPLD_BASE)
+
+#define CONFIG_SYS_CSPR2 (CSPR_PHYS_ADDR(CONFIG_SYS_CPLD_BASE_PHYS) \
+ | CSPR_PORT_SIZE_8 \
+ | CSPR_MSEL_GPCM \
+ | CSPR_V)
+#define CONFIG_SYS_AMASK2 IFC_AMASK(64*1024)
+#define CONFIG_SYS_CSOR2 0x0
+/* CPLD Timing parameters for IFC CS2 */
+#define CONFIG_SYS_CS2_FTIM0 (FTIM0_GPCM_TACSE(0x0e) | \
+ FTIM0_GPCM_TEADC(0x0e) | \
+ FTIM0_GPCM_TEAHC(0x0e))
+#define CONFIG_SYS_CS2_FTIM1 (FTIM1_GPCM_TACO(0x0e) | \
+ FTIM1_GPCM_TRAD(0x1f))
+#define CONFIG_SYS_CS2_FTIM2 (FTIM2_GPCM_TCS(0x0e) | \
+ FTIM2_GPCM_TCH(0x0) | \
+ FTIM2_GPCM_TWP(0x1f))
+#define CONFIG_SYS_CS2_FTIM3 0x0
+
+#if defined(CONFIG_RAMBOOT_SPIFLASH)
+#define CONFIG_SYS_RAMBOOT
+#define CONFIG_SYS_EXTRA_ENV_RELOC
+#else
+#undef CONFIG_SYS_RAMBOOT
+#endif
+
+#define CONFIG_BOARD_EARLY_INIT_R
+
+#define CONFIG_SYS_INIT_RAM_LOCK
+#define CONFIG_SYS_INIT_RAM_ADDR 0xffd00000
+#define CONFIG_SYS_INIT_RAM_END 0x00004000
+
+#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END \
+ - GENERATED_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
+
+#define CONFIG_SYS_MONITOR_LEN (512 * 1024)
+#define CONFIG_SYS_MALLOC_LEN (1024 * 1024)
+
+/* Serial Port */
+#define CONFIG_CONS_INDEX 1
+#define CONFIG_SYS_NS16550
+#define CONFIG_SYS_NS16550_SERIAL
+#define CONFIG_SYS_NS16550_REG_SIZE 1
+#define CONFIG_SYS_NS16550_CLK get_bus_freq(0)
+
+#define CONFIG_SERIAL_MULTI /* Enable both serial ports */
+#define CONFIG_SYS_CONSOLE_IS_IN_ENV
+
+#define CONFIG_SYS_BAUDRATE_TABLE \
+ {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
+
+#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x4500)
+#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x4600)
+
+/* Use the HUSH parser */
+#define CONFIG_SYS_HUSH_PARSER
+#define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
+
+/*
+ * Pass open firmware flat tree
+ */
+#define CONFIG_OF_LIBFDT
+#define CONFIG_OF_BOARD_SETUP
+#define CONFIG_OF_STDOUT_VIA_ALIAS
+
+/* new uImage format support */
+#define CONFIG_FIT
+#define CONFIG_FIT_VERBOSE /* enable fit_format_{error,warning}() */
+
+#define CONFIG_FSL_I2C
+#define CONFIG_HARD_I2C
+#define CONFIG_I2C_MULTI_BUS
+#define CONFIG_I2C_CMD_TREE
+#define CONFIG_SYS_I2C_SPEED 400000
+#define CONFIG_SYS_I2C_SLAVE 0x7F
+#define CONFIG_SYS_I2C_OFFSET 0x3000
+#define CONFIG_SYS_I2C2_OFFSET 0x3100
+
+/* I2C EEPROM */
+/* enable read and write access to EEPROM */
+#define CONFIG_CMD_EEPROM
+#define CONFIG_SYS_I2C_MULTI_EEPROMS
+#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2
+#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3
+#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 5
+
+#define CONFIG_CMD_I2C
+
+/* eSPI - Enhanced SPI */
+#define CONFIG_FSL_ESPI
+#define CONFIG_SPI_FLASH
+#define CONFIG_SPI_FLASH_SPANSION
+#define CONFIG_SPI_FLASH_EON
+#define CONFIG_CMD_SF
+#define CONFIG_SF_DEFAULT_SPEED 10000000
+#define CONFIG_SF_DEFAULT_MODE SPI_MODE_0
+
+#ifdef CONFIG_TSEC_ENET
+#define CONFIG_NET_MULTI
+#define CONFIG_MII /* MII PHY management */
+#define CONFIG_MII_DEFAULT_TSEC 1 /* Allow unregistered phys */
+#define CONFIG_TSEC1 1
+#define CONFIG_TSEC1_NAME "eTSEC1"
+#define CONFIG_TSEC2 1
+#define CONFIG_TSEC2_NAME "eTSEC2"
+
+/* Default mode is RGMII mode */
+#define TSEC1_PHY_ADDR 0
+#define TSEC2_PHY_ADDR 2
+
+#define TSEC1_FLAGS (TSEC_GIGABIT | TSEC_REDUCED)
+#define TSEC2_FLAGS (TSEC_GIGABIT | TSEC_REDUCED)
+
+#define CONFIG_ETHPRIME "eTSEC1"
+
+#define CONFIG_PHY_GIGE
+#endif /* CONFIG_TSEC_ENET */
+
+/*
+ * Environment
+ */
+#if defined(CONFIG_SYS_RAMBOOT)
+#if defined(CONFIG_RAMBOOT_SPIFLASH)
+#define CONFIG_ENV_IS_IN_SPI_FLASH
+#define CONFIG_ENV_SPI_BUS 0
+#define CONFIG_ENV_SPI_CS 0
+#define CONFIG_ENV_SPI_MAX_HZ 10000000
+#define CONFIG_ENV_SPI_MODE 0
+#define CONFIG_ENV_OFFSET 0x100000 /* 1MB */
+#define CONFIG_ENV_SECT_SIZE 0x10000
+#define CONFIG_ENV_SIZE 0x2000
+#endif
+#else
+#define CONFIG_ENV_IS_IN_FLASH
+#if CONFIG_SYS_MONITOR_BASE > 0xfff80000
+#define CONFIG_ENV_ADDR 0xfff80000
+#else
+#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - CONFIG_ENV_SECT_SIZE)
+#endif
+#define CONFIG_ENV_SIZE 0x2000
+#define CONFIG_ENV_SECT_SIZE 0x20000
+#endif
+
+#define CONFIG_LOADS_ECHO
+#define CONFIG_SYS_LOADS_BAUD_CHANGE
+
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_ERRATA
+#define CONFIG_CMD_ELF
+#define CONFIG_CMD_IRQ
+#define CONFIG_CMD_MII
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_SETEXPR
+#define CONFIG_CMD_REGINFO
+
+/*
+ * Miscellaneous configurable options
+ */
+#define CONFIG_SYS_LONGHELP /* undef to save memory */
+#define CONFIG_CMDLINE_EDITING /* Command-line editing */
+#define CONFIG_AUTO_COMPLETE /* add autocompletion support */
+#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */
+#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */
+
+#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
+ /* Print Buffer Size */
+#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
+#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE/* Boot Argument Buffer Size */
+#define CONFIG_SYS_HZ 1000 /* dec freq: 1ms ticks */
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 64 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define CONFIG_SYS_BOOTMAPSZ (64 << 20) /* Initial Memory map for Linux */
+#define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */
+
+/*
+ * Environment Configuration
+ */
+
+#ifdef CONFIG_TSEC_ENET
+#define CONFIG_HAS_ETH0
+#define CONFIG_HAS_ETH1
+#endif
+
+#define CONFIG_ROOTPATH "/opt/nfsroot"
+#define CONFIG_BOOTFILE "uImage"
+#define CONFIG_UBOOTPATH u-boot.bin/* U-Boot image on TFTP server */
+
+/* default location for tftp and bootm */
+#define CONFIG_LOADADDR 1000000
+
+#define CONFIG_BOOTDELAY 10 /* -1 disables auto-boot */
+
+#define CONFIG_BAUDRATE 115200
+
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ "hwconfig=" __stringify(CONFIG_DEF_HWCONFIG) "\0" \
+ "netdev=eth0\0" \
+ "uboot=" __stringify(CONFIG_UBOOTPATH) "\0" \
+ "loadaddr=1000000\0" \
+ "consoledev=ttyS0\0" \
+ "ramdiskaddr=2000000\0" \
+ "ramdiskfile=rootfs.ext2.gz.uboot\0" \
+ "fdtaddr=c00000\0" \
+ "fdtfile=name/of/device-tree.dtb\0" \
+ "othbootargs=ramdisk_size=600000\0" \
+
+#define CONFIG_RAMBOOTCOMMAND \
+ "setenv bootargs root=/dev/ram rw " \
+ "console=$consoledev,$baudrate $othbootargs; " \
+ "tftp $ramdiskaddr $ramdiskfile;" \
+ "tftp $loadaddr $bootfile;" \
+ "tftp $fdtaddr $fdtfile;" \
+ "bootm $loadaddr $ramdiskaddr $fdtaddr"
+
+#define CONFIG_BOOTCOMMAND CONFIG_RAMBOOTCOMMAND
+
+#endif /* __CONFIG_H */
--
1.8.0
More information about the U-Boot
mailing list