[U-Boot] [PATCH v6] spi: pl022_spi: Add support for ARM PL022 spi controller
Jagan Teki
jagannadh.teki at gmail.com
Wed Jun 12 16:25:38 CEST 2013
Thanks for v6 sent.
Have you tested this?
on which board, include/configs/*.h file?
--
Thanks,
Jagan.
On Wed, Jun 12, 2013 at 6:17 PM, Armando Visconti
<armando.visconti at st.com> wrote:
> This patch adds the support for the ARM PL022 SPI controller for the standard
> variant (0x00041022), which has a 16bit wide and 8 locations deep TX/RX FIFO.
>
> Signed-off-by: Armando Visconti <armando.visconti at st.com>
> Signed-off-by: Vipin Kumar <vipin.kumar at st.com>
> Acked-by: Stefan Roese <sr at denx.de>
> ---
> v5->v6
>
> 1. Make use of spi_alloc_slave() macro.
> 2. Changed the identation on 'if statement' as requested
> by Jagan.
>
> drivers/spi/Makefile | 1 +
> drivers/spi/pl022_spi.c | 308 ++++++++++++++++++++++++++++++++++++++++++++++++
> 2 files changed, 309 insertions(+)
> create mode 100644 drivers/spi/pl022_spi.c
>
> diff --git a/drivers/spi/Makefile b/drivers/spi/Makefile
> index d08609e..b6443b1 100644
> --- a/drivers/spi/Makefile
> +++ b/drivers/spi/Makefile
> @@ -47,6 +47,7 @@ COBJS-$(CONFIG_MXC_SPI) += mxc_spi.o
> COBJS-$(CONFIG_MXS_SPI) += mxs_spi.o
> COBJS-$(CONFIG_OC_TINY_SPI) += oc_tiny_spi.o
> COBJS-$(CONFIG_OMAP3_SPI) += omap3_spi.o
> +COBJS-$(CONFIG_PL022_SPI) += pl022_spi.o
> COBJS-$(CONFIG_SOFT_SPI) += soft_spi.o
> COBJS-$(CONFIG_SH_SPI) += sh_spi.o
> COBJS-$(CONFIG_FSL_ESPI) += fsl_espi.o
> diff --git a/drivers/spi/pl022_spi.c b/drivers/spi/pl022_spi.c
> new file mode 100644
> index 0000000..5b47413
> --- /dev/null
> +++ b/drivers/spi/pl022_spi.c
> @@ -0,0 +1,308 @@
> +/*
> + * (C) Copyright 2012
> + * Armando Visconti, ST Microelectronics, armando.visconti at st.com.
> + *
> + * Driver for ARM PL022 SPI Controller. Based on atmel_spi.c
> + * by Atmel Corporation.
> + *
> + * This program is free software; you can redistribute it and/or
> + * modify it under the terms of the GNU General Public License as
> + * published by the Free Software Foundation; either version 2 of
> + * the License, or (at your option) any later version.
> + *
> + * This program is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> + * GNU General Public License for more details.
> + *
> + * You should have received a copy of the GNU General Public License
> + * along with this program; if not, write to the Free Software
> + * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
> + * MA 02111-1307 USA
> + */
> +
> +#include <common.h>
> +#include <malloc.h>
> +#include <spi.h>
> +#include <asm/io.h>
> +#include <asm/arch/hardware.h>
> +
> +/* SSP registers mapping */
> +struct pl022 {
> + u32 ssp_cr0; /* 0x000 */
> + u32 ssp_cr1; /* 0x004 */
> + u32 ssp_dr; /* 0x008 */
> + u32 ssp_sr; /* 0x00c */
> + u32 ssp_cpsr; /* 0x010 */
> + u32 ssp_imsc; /* 0x014 */
> + u32 ssp_ris; /* 0x018 */
> + u32 ssp_mis; /* 0x01c */
> + u32 ssp_icr; /* 0x020 */
> + u32 ssp_dmacr; /* 0x024 */
> + u8 reserved_1[0x080 - 0x028];
> + u32 ssp_itcr; /* 0x080 */
> + u32 ssp_itip; /* 0x084 */
> + u32 ssp_itop; /* 0x088 */
> + u32 ssp_tdr; /* 0x08c */
> + u8 reserved_2[0xFE0 - 0x090];
> + u32 ssp_pid0; /* 0xfe0 */
> + u32 ssp_pid1; /* 0xfe4 */
> + u32 ssp_pid2; /* 0xfe8 */
> + u32 ssp_pid3; /* 0xfec */
> + u32 ssp_cid0; /* 0xff0 */
> + u32 ssp_cid1; /* 0xff4 */
> + u32 ssp_cid2; /* 0xff8 */
> + u32 ssp_cid3; /* 0xffc */
> +};
> +
> +/* SSP Control Register 0 - SSP_CR0 */
> +#define SSP_CR0_SPO (0x1 << 6)
> +#define SSP_CR0_SPH (0x1 << 7)
> +#define SSP_CR0_8BIT_MODE (0x07)
> +#define SSP_SCR_MAX (0xFF)
> +#define SSP_SCR_SHFT 8
> +
> +/* SSP Control Register 0 - SSP_CR1 */
> +#define SSP_CR1_MASK_SSE (0x1 << 1)
> +
> +#define SSP_CPSR_MAX (0xFE)
> +
> +/* SSP Status Register - SSP_SR */
> +#define SSP_SR_MASK_TFE (0x1 << 0) /* Transmit FIFO empty */
> +#define SSP_SR_MASK_TNF (0x1 << 1) /* Transmit FIFO not full */
> +#define SSP_SR_MASK_RNE (0x1 << 2) /* Receive FIFO not empty */
> +#define SSP_SR_MASK_RFF (0x1 << 3) /* Receive FIFO full */
> +#define SSP_SR_MASK_BSY (0x1 << 4) /* Busy Flag */
> +
> +struct pl022_spi_slave {
> + struct spi_slave slave;
> + void *regs;
> + unsigned int freq;
> +};
> +
> +static inline struct pl022_spi_slave *to_pl022_spi(struct spi_slave *slave)
> +{
> + return container_of(slave, struct pl022_spi_slave, slave);
> +}
> +
> +/*
> + * Following three functions should be provided by the
> + * board support package.
> + */
> +int __weak spi_cs_is_valid(unsigned int bus, unsigned int cs)
> +{
> + return 1;
> +}
> +
> +void __weak spi_cs_activate(struct spi_slave *slave)
> +{
> + /* do nothing */
> +}
> +
> +void __weak spi_cs_deactivate(struct spi_slave *slave)
> +{
> + /* do nothing */
> +}
> +
> +void spi_init(void)
> +{
> + /* do nothing */
> +}
> +
> +/*
> + * ARM PL022 exists in different 'flavors'.
> + * This drivers currently support the standard variant (0x00041022), that has a
> + * 16bit wide and 8 locations deep TX/RX FIFO.
> + */
> +static int pl022_is_supported(struct pl022_spi_slave *ps)
> +{
> + struct pl022 *pl022 = (struct pl022 *)ps->regs;
> +
> + /* PL022 version is 0x00041022 */
> + if ((readl(&pl022->ssp_pid0) == 0x22) &&
> + (readl(&pl022->ssp_pid1) == 0x10) &&
> + ((readl(&pl022->ssp_pid2) & 0xf) == 0x04) &&
> + (readl(&pl022->ssp_pid3) == 0x00))
> + return 1;
> +
> + return 0;
> +}
> +
> +struct spi_slave *spi_setup_slave(unsigned int bus, unsigned int cs,
> + unsigned int max_hz, unsigned int mode)
> +{
> + struct pl022_spi_slave *ps;
> + struct pl022 *pl022;
> + u16 scr = 1, prescaler, cr0 = 0, cpsr = 0;
> +
> + if (!spi_cs_is_valid(bus, cs))
> + return NULL;
> +
> + ps = spi_alloc_slave(struct pl022_spi_slave, bus, cs);
> + if (!ps)
> + return NULL;
> +
> + ps->freq = max_hz;
> +
> + switch (bus) {
> + case 0:
> + ps->regs = (void *)CONFIG_SYS_SPI_BASE;
> + break;
> +#ifdef CONFIG_SYS_SPI_BASE1
> + case 1:
> + ps->regs = (void *)CONFIG_SYS_SPI_BASE1;
> + break;
> +#endif
> +#ifdef CONFIG_SYS_SPI_BASE2
> + case 2:
> + ps->regs = (void *)CONFIG_SYS_SPI_BASE2;
> + break;
> +#endif
> +#ifdef CONFIG_SYS_SPI_BASE3
> + case 3:
> + ps->regs = (void *)CONFIG_SYS_SPI_BASE3;
> + break;
> +#endif
> + default:
> + free(ps);
> + return NULL;
> + }
> +
> + pl022 = (struct pl022 *)ps->regs;
> +
> + /* Check the PL022 version */
> + if (!pl022_is_supported(ps)) {
> + free(ps);
> + return NULL;
> + }
> +
> + /* Set requested polarity and 8bit mode */
> + cr0 = SSP_CR0_8BIT_MODE;
> + cr0 |= (mode & SPI_CPHA) ? SSP_CR0_SPH : 0;
> + cr0 |= (mode & SPI_CPOL) ? SSP_CR0_SPO : 0;
> +
> + writel(cr0, &pl022->ssp_cr0);
> +
> + /* Program the SSPClk frequency */
> + prescaler = CONFIG_SYS_SPI_CLK / ps->freq;
> +
> + if (prescaler <= 0xFF) {
> + cpsr = prescaler;
> + } else {
> + for (scr = 1; scr <= SSP_SCR_MAX; scr++) {
> + if (!(prescaler % scr)) {
> + cpsr = prescaler / scr;
> + if (cpsr <= SSP_CPSR_MAX)
> + break;
> + }
> + }
> +
> + if (scr > SSP_SCR_MAX) {
> + scr = SSP_SCR_MAX;
> + cpsr = prescaler / scr;
> + cpsr &= SSP_CPSR_MAX;
> + }
> + }
> +
> + if (cpsr & 0x1)
> + cpsr++;
> +
> + writel(cpsr, &pl022->ssp_cpsr);
> + cr0 = readl(&pl022->ssp_cr0);
> + writel(cr0 | (scr - 1) << SSP_SCR_SHFT, &pl022->ssp_cr0);
> +
> + return &ps->slave;
> +}
> +
> +void spi_free_slave(struct spi_slave *slave)
> +{
> + struct pl022_spi_slave *ps = to_pl022_spi(slave);
> +
> + free(ps);
> +}
> +
> +int spi_claim_bus(struct spi_slave *slave)
> +{
> + struct pl022_spi_slave *ps = to_pl022_spi(slave);
> + struct pl022 *pl022 = (struct pl022 *)ps->regs;
> +
> + /* Enable the SPI hardware */
> + setbits_le32(&pl022->ssp_cr1, SSP_CR1_MASK_SSE);
> +
> + return 0;
> +}
> +
> +void spi_release_bus(struct spi_slave *slave)
> +{
> + struct pl022_spi_slave *ps = to_pl022_spi(slave);
> + struct pl022 *pl022 = (struct pl022 *)ps->regs;
> +
> + /* Disable the SPI hardware */
> + writel(0x0, &pl022->ssp_cr1);
> +}
> +
> +int spi_xfer(struct spi_slave *slave, unsigned int bitlen,
> + const void *dout, void *din, unsigned long flags)
> +{
> + struct pl022_spi_slave *ps = to_pl022_spi(slave);
> + struct pl022 *pl022 = (struct pl022 *)ps->regs;
> + u32 len_tx = 0, len_rx = 0, len;
> + u32 ret = 0;
> + const u8 *txp = dout;
> + u8 *rxp = din, value;
> +
> + if (bitlen == 0)
> + /* Finish any previously submitted transfers */
> + goto out;
> +
> + /*
> + * TODO: The controller can do non-multiple-of-8 bit
> + * transfers, but this driver currently doesn't support it.
> + *
> + * It's also not clear how such transfers are supposed to be
> + * represented as a stream of bytes...this is a limitation of
> + * the current SPI interface.
> + */
> + if (bitlen % 8) {
> + ret = -1;
> +
> + /* Errors always terminate an ongoing transfer */
> + flags |= SPI_XFER_END;
> + goto out;
> + }
> +
> + len = bitlen / 8;
> +
> + if (flags & SPI_XFER_BEGIN)
> + spi_cs_activate(slave);
> +
> + while (len_tx < len) {
> + if (readl(&pl022->ssp_sr) & SSP_SR_MASK_TNF) {
> + value = (txp != NULL) ? *txp++ : 0;
> + writel(value, &pl022->ssp_dr);
> + len_tx++;
> + }
> +
> + if (readl(&pl022->ssp_sr) & SSP_SR_MASK_RNE) {
> + value = readl(&pl022->ssp_dr);
> + if (rxp)
> + *rxp++ = value;
> + len_rx++;
> + }
> + }
> +
> + while (len_rx < len_tx) {
> + if (readl(&pl022->ssp_sr) & SSP_SR_MASK_RNE) {
> + value = readl(&pl022->ssp_dr);
> + if (rxp)
> + *rxp++ = value;
> + len_rx++;
> + }
> + }
> +
> +out:
> + if (flags & SPI_XFER_END)
> + spi_cs_deactivate(slave);
> +
> + return ret;
> +}
> --
> 1.7.11.7
>
More information about the U-Boot
mailing list