[U-Boot] [PATCH] arm: omap4: panda: Add reading of the board revision

Dan Murphy dmurphy at ti.com
Thu Jun 13 14:42:58 CEST 2013


On 06/12/2013 12:54 PM, Dan Murphy wrote:
> Detect if we are running on a panda revision A1-A6,
> or an ES panda board. This can be done by reading
> the level of GPIOs and checking the processor revisions.
> This should result in:
> Panda 4430:
>      GPIO171, GPIO101, GPIO182: 0 1 1 => A1-A5
>      GPIO171, GPIO101, GPIO182: 1 0 1 => A6
> Panda ES:
>      GPIO2, GPIO3, GPIO171, GPIO48, GPIO182: 0 0 0 1 1 => B1/B2
>      GPIO2, GPIO3, GPIO171, GPIO48, GPIO182: 0 0 1 1 1 => B3
>
> Set the board name appropriately for the board revision that
> is detected.
>
> Update the findfdt macro to load the a4 device tree binary.
>
> Signed-off-by: Dan Murphy <dmurphy at ti.com>
> ---
>  board/ti/panda/panda.c         |   71 +++++++++++++++++++++++++++++++++++++---
>  include/configs/omap4_common.h |    2 +
>  2 files changed, 68 insertions(+), 5 deletions(-)
>
> diff --git a/board/ti/panda/panda.c b/board/ti/panda/panda.c
> index 2bbe392..65a6e14 100644
> --- a/board/ti/panda/panda.c
> +++ b/board/ti/panda/panda.c
> @@ -37,6 +37,11 @@
>  #endif
>  
>  #define PANDA_ULPI_PHY_TYPE_GPIO       182
> +#define PANDA_BOARD_ID_1_GPIO          101
> +#define PANDA_ES_BOARD_ID_1_GPIO        48
> +#define PANDA_BOARD_ID_2_GPIO          171
> +#define PANDA_ES_BOARD_ID_3_GPIO         3
> +#define PANDA_ES_BOARD_ID_4_GPIO         2
>  
>  DECLARE_GLOBAL_DATA_PTR;
>  
> @@ -66,6 +71,66 @@ int board_eth_init(bd_t *bis)
>  	return 0;
>  }
>  
> +/*
> +* Routine: get_board_revision
> +* Description: Detect if we are running on a panda revision A1-A6,
> +*              or an ES panda board. This can be done by reading
> +*              the level of GPIOs and checking the processor revisions.
> +*              This should result in:
> +*			Panda 4430:
> +*              GPIO171, GPIO101, GPIO182: 0 1 1 => A1-A5
> +*              GPIO171, GPIO101, GPIO182: 1 0 1 => A6
> +*			Panda ES:
> +*              GPIO2, GPIO3, GPIO171, GPIO48, GPIO182: 0 0 0 1 1 => B1/B2
> +*              GPIO2, GPIO3, GPIO171, GPIO48, GPIO182: 0 0 1 1 1 => B3
> +*/
> +int get_board_revision(void)
> +{
> +	int board_id0, board_id1, board_id2;
> +	int board_id3, board_id4;
> +	int board_id;
> +
> +	int processor_rev = omap_revision();
> +
> +	/* Setup the mux for the common board ID pins */
> +	writew((IEN | M3), CONTROL_PADCONF_CORE + UNIPRO_TX0); /* gpio 171 */
> +	writew((IEN | M3), CONTROL_PADCONF_CORE + FREF_CLK2_OUT); /* gpio 182 */
> +
> +	board_id0 = gpio_get_value(PANDA_ULPI_PHY_TYPE_GPIO);
> +	board_id2 = gpio_get_value(PANDA_BOARD_ID_2_GPIO);
> +
> +	if (processor_rev >= OMAP4460_ES1_0 &&
> +		processor_rev <= OMAP4460_ES1_1) {
> +		/* Setup the mux for the ES specific board ID pins */
> +		writew((IEN | M3), CONTROL_PADCONF_CORE + GPMC_A24); /* gpio 101 */
> +		writew((IEN | M3), CONTROL_PADCONF_CORE + UNIPRO_RY0); /* gpio 2 */
> +		writew((IEN | M3), CONTROL_PADCONF_CORE + UNIPRO_RX1); /* gpio 3 */
> +
> +		board_id1 = gpio_get_value(PANDA_ES_BOARD_ID_1_GPIO);
> +		board_id3 = gpio_get_value(PANDA_ES_BOARD_ID_3_GPIO);
> +		board_id4 = gpio_get_value(PANDA_ES_BOARD_ID_4_GPIO);
> +
> +#ifdef CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG
> +			setenv("board_name", strcat(CONFIG_SYS_BOARD, "-es"));
> +#endif
> +		board_id = ((board_id4 << 4) | (board_id3 << 3) | (board_id2 << 2) |
> +			(board_id1 << 1) | (board_id0));
> +	} else {
> +		/* Setup the mux for the Ax specific board ID pins */
> +		writew((IEN | M3), CONTROL_PADCONF_CORE + FREF_CLK2_OUT); /* gpio 101 */
> +
> +		board_id1 = gpio_get_value(PANDA_BOARD_ID_1_GPIO);
> +		board_id = ((board_id2 << 2) | (board_id1 << 1) | (board_id0));
> +
> +#ifdef CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG
> +			if ((board_id >= 0x3) && (processor_rev == OMAP4430_ES2_3))
> +				setenv("board_name", strcat(CONFIG_SYS_BOARD, "-a4"));
> +#endif
> +	}
> +
> +	return board_id;
> +}
> +
>  /**
>   * @brief misc_init_r - Configure Panda board specific configurations
>   * such as power configurations, ethernet initialization as phase2 of
> @@ -82,11 +147,7 @@ int misc_init_r(void)
>  	if (omap_revision() == OMAP4430_ES1_0)
>  		return 0;
>  
> -#ifdef CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG
> -	if (omap_revision() >= OMAP4460_ES1_0 ||
> -		omap_revision() <= OMAP4460_ES1_1)
> -		setenv("board_name", strcat(CONFIG_SYS_BOARD, "-es"));
> -#endif
> +	get_board_revision();
>  
>  	gpio_direction_input(PANDA_ULPI_PHY_TYPE_GPIO);
>  	phy_type = gpio_get_value(PANDA_ULPI_PHY_TYPE_GPIO);
> diff --git a/include/configs/omap4_common.h b/include/configs/omap4_common.h
> index d6448b0..cf41d9c 100644
> --- a/include/configs/omap4_common.h
> +++ b/include/configs/omap4_common.h
> @@ -181,6 +181,8 @@
>  			"setenv fdtfile omap4-sdp.dtb; fi; " \
>  		"if test $board_name = panda; then " \
>  			"setenv fdtfile omap4-panda.dtb; fi;" \
> +		"if test $board_name = panda-a4; then " \
> +			"setenv fdtfile omap4-panda-a4.dtb; fi;" \
>  		"if test $board_name = panda-es; then " \
>  			"setenv fdtfile omap4-panda-es.dtb; fi; \0" \
>  	"loadfdt=load mmc ${bootpart} ${fdtaddr} ${bootdir}/${fdtfile}\0" \
Tested on A3, A6 and ES B2.

Dan

-- 
------------------
Dan Murphy



More information about the U-Boot mailing list