[U-Boot] [PATH v5 03/14] sf: Read flash bank addr register at probe time

[Jagannadha Sutradharudu Teki]

Read the flash bank addr register to get the state of bank in
a perticular flash. and also bank write happens only when there is
a change in bank selection from user.

bank read only valid for flashes which has > 16Mbytes those are
opearted in 3-byte addr mode, each bank occupies 16Mytes.

Suppose if the flash has 64Mbytes size consists of 4 banks like
bank0, bank1, bank2 and bank3.

Signed-off-by: Jagannadha Sutradharudu Teki <jaganna at xilinx.com>
Reviewed-by: Simon Glass <sjg at chromium.org>
---
Changes for v5:
	- bank_read_cmd <= bank_cmd[0]
	- bank_write_cmd <= bank_cmd[1]
Changes for v4:
	- Added spi_flash_bank_config
Changes for v3:
	- none
Changes for v2:
	- none

 drivers/mtd/spi/spi_flash.c          | 27 +++++++++++++++++++++++++++
 drivers/mtd/spi/spi_flash_internal.h |  2 ++
 include/spi_flash.h                  |  2 ++
 3 files changed, 31 insertions(+)

diff --git a/drivers/mtd/spi/spi_flash.c b/drivers/mtd/spi/spi_flash.c
index 7e19953..64b57ec 100644
--- a/drivers/mtd/spi/spi_flash.c
+++ b/drivers/mtd/spi/spi_flash.c
@@ -283,6 +283,12 @@ int spi_flash_cmd_bankaddr_write(struct spi_flash *flash, u8 bank_sel)
 	u8 cmd;
 	int ret;
 
+	if (flash->bank_curr == bank_sel) {
+		debug("SF: not require to enable bank%d\n", bank_sel);
+		return 0;
+	}
+
+	cmd = flash->bank_write_cmd;
 	ret = spi_flash_cmd_write_enable(flash);
 	if (ret < 0) {
 		debug("SF: enabling write failed\n");
@@ -294,6 +300,7 @@ int spi_flash_cmd_bankaddr_write(struct spi_flash *flash, u8 bank_sel)
 		debug("SF: fail to write bank addr register\n");
 		return ret;
 	}
+	flash->bank_curr = bank_sel;
 
 	ret = spi_flash_cmd_wait_ready(flash, SPI_FLASH_PROG_TIMEOUT);
 	if (ret < 0) {
@@ -306,6 +313,9 @@ int spi_flash_cmd_bankaddr_write(struct spi_flash *flash, u8 bank_sel)
 
 int spi_flash_bank_config(struct spi_flash *flash, u8 idcode0)
 {
+	u8 cmd;
+	u8 curr_bank = 0;
+
 	/* discover bank cmds */
 	switch (idcode0) {
 	case SPI_FLASH_SPANSION_IDCODE0:
@@ -322,6 +332,18 @@ int spi_flash_bank_config(struct spi_flash *flash, u8 idcode0)
 		return -1;
 	}
 
+	/* read the bank reg - on which bank the flash is in currently */
+	cmd = flash->bank_read_cmd;
+	if (flash->size > SPI_FLASH_16MB_BOUN) {
+		if (spi_flash_read_common(flash, &cmd, 1, &curr_bank, 1)) {
+			debug("SF: fail to read bank addr register\n");
+			return -1;
+		}
+		flash->bank_curr = curr_bank;
+	} else {
+		flash->bank_curr = curr_bank;
+	}
+
 	return 0;
 }
 
@@ -469,6 +491,11 @@ struct spi_flash *spi_flash_probe(unsigned int bus, unsigned int cs,
 		goto err_manufacturer_probe;
 	}
 
+	/* Configure the BAR - disover bank cmds and read current bank  */
+	ret = spi_flash_bank_config(flash, *idp);
+	if (ret < 0)
+		goto err_manufacturer_probe;
+
 #ifdef CONFIG_OF_CONTROL
 	if (spi_flash_decode_fdt(gd->fdt_blob, flash)) {
 		debug("SF: FDT decode error\n");
diff --git a/drivers/mtd/spi/spi_flash_internal.h b/drivers/mtd/spi/spi_flash_internal.h
index db6c444..00ed1ee 100644
--- a/drivers/mtd/spi/spi_flash_internal.h
+++ b/drivers/mtd/spi/spi_flash_internal.h
@@ -28,6 +28,8 @@
 #define CMD_ERASE_64K			0xd8
 #define CMD_ERASE_CHIP			0xc7
 
+#define SPI_FLASH_16MB_BOUN		0x1000000
+
 /* Manufacture ID's */
 #define SPI_FLASH_SPANSION_IDCODE0	0x01
 #define SPI_FLASH_STMICRO_IDCODE0	0x20
diff --git a/include/spi_flash.h b/include/spi_flash.h
index 38587c2..91b43ee 100644
--- a/include/spi_flash.h
+++ b/include/spi_flash.h
@@ -42,6 +42,8 @@ struct spi_flash {
 	u8		bank_read_cmd;
 	/* Bank write cmd */
 	u8		bank_write_cmd;
+	/* Current flash bank */
+	u8		bank_curr;
 
 	void *memory_map;	/* Address of read-only SPI flash access */
 	int		(*read)(struct spi_flash *flash, u32 offset,
-- 
1.8.3