[U-Boot] [PULL] : Please pull u-boot-imx
Albert ARIBAUD
albert.u.boot at aribaud.net
Fri Mar 15 19:51:15 CET 2013
Hi Stefano,
On Fri, 15 Mar 2013 14:54:06 +0100, Stefano Babic <sbabic at denx.de>
wrote:
> Hi Albert,
>
> here an update pull request after applying Fabio's fixes.
>
> The following changes since commit 4cfc611b4a4ce009cfad46804bec2a1caad8e329:
>
> ARM: ns9750dev: remove remainders of dead board (2013-02-28 14:49:24
> +0100)
>
> are available in the git repository at:
>
> git://www.denx.de/git/u-boot-imx.git master
>
> for you to fetch changes up to 19a0f7fa271de0345bb2df90d443c547c41e8037:
>
> nitrogen: Use unsigned long to specify the total RAM size (2013-03-15
> 14:39:44 +0100)
>
> ----------------------------------------------------------------
> Benoît Thébaudeau (6):
> imx: mx6q DDR3 init: Fix tMRD
> imx: mx6q DDR3 init: Fix tXPR
> imx: mx6q DDR3 init: Fix SDE_to_RST
> imx: mx6q DDR3 init: Fix RST_to_CKE
> imx: mx6q DDR3 init: Fix MR0.PPD
> imx: mx6q DDR3 init: Benefit from available CL = 7
>
> Eric Nelson (8):
> i.MX6Q: mx6qsabre*: Configure to allow CONFIG_SYS_ALT_MEMTEST
> i.MX6: mx6qsabrelite: indent with tabs
> i.MX6: consolidate pad names for multi-CPU boards
> i.MX6: crm_regs: define CCM_CCGRx for use in board config files
> i.MX6: crm_regs: define IOMUXC_GPR4/6/7
> i.MX6DL: define IOMUX pads NANDF_CS1-3 for use as GPIO
> i.MX6: Add DDR controller registers
> Add Boundary Devices Nitrogen6X boards
>
> Fabio Estevam (6):
> mx6: Disable Power Down Bit of watchdog
> mx23evk: Remove CONFIG_SYS_BAUDRATE_TABLE
> mx23evk: Turn on caches
> common: cmd_sata: Fix usage text for 'sata init'
> mx6: Provide a structure for accessing HDMI registers
> nitrogen6x: Fix RAM size variable
>
> Fadil Berisha (2):
> mxs: timrot: Add support to i.MX23
> mxs: timrot: Rename local macros
>
> Marek Vasut (7):
> mxs: Reset the EMI block on mx23
> mxs: mmc: spi: dma: Better wrap the MXS differences
> mxs: spi: Fix the MXS SPI for mx23
> mxs: spi: Remove CONFIG_MXS_SPI_DMA_ENABLE
> mxs: Squash the header file usage in ehci-mxs
> mxs: Make ehci-mxs multiport capable
> mxs: m28: Enable power to USB port 0
>
> Otavio Salvador (11):
> build: imx: Fix 'u-boot.imx' build without full OBJTREE reference
> mxs: Rename CONFIG_SPL_MX28_PSWITCH_WAIT to
> CONFIG_SPL_MXS_PSWITCH_WAIT
> mx23: Document the tRAS lockout setting in memory initialization
> mx23evk: Adjust DRAM control register to use full 128MB of RAM
> led: Use STATUS_LED_ON and STATUS_LED_OFF when calling __led_set
> mxs: Fix iomux.h to not break build during assembly stage
> mx23_olinuxino: Add support for status LED
> mx23evk: Enable USB support
> mx23_olinuxino: Enable USB support
> mx23_olinuxino: Add ethernet support
> mx23_olinuxino: Fix warning for implicit declaration
>
> Stefano Babic (3):
> Merge branch 'master' of git://git.denx.de/u-boot-arm
> Merge branch 'master' of git://git.denx.de/u-boot-arm
> USB: drop unneeded header in ehci-mx6
>
> Stephen Warren (1):
> ARM: mx6: use common CPU errata config options
>
> fabio.estevam at freescale.com (1):
> nitrogen: Use unsigned long to specify the total RAM size
>
> MAINTAINERS | 8 +
> Makefile | 4 +-
> arch/arm/cpu/arm926ejs/config.mk | 2 +-
> arch/arm/cpu/arm926ejs/mxs/clock.c | 3 +-
> arch/arm/cpu/arm926ejs/mxs/mxs_init.h | 2 +-
> arch/arm/cpu/arm926ejs/mxs/spl_mem_init.c | 16 +-
> arch/arm/cpu/arm926ejs/mxs/spl_power_init.c | 2 +-
> arch/arm/cpu/arm926ejs/mxs/timer.c | 39 +-
> arch/arm/cpu/armv7/Makefile | 2 +-
> arch/arm/cpu/armv7/config.mk | 2 +-
> arch/arm/cpu/armv7/mx6/Makefile | 1 -
> arch/arm/cpu/armv7/mx6/lowlevel_init.S | 35 -
> arch/arm/cpu/armv7/mx6/soc.c | 16 +
> arch/arm/include/asm/arch-mx6/crm_regs.h | 12 +
> arch/arm/include/asm/arch-mx6/imx-regs.h | 8 +
> arch/arm/include/asm/arch-mx6/iomux.h | 5 +
> arch/arm/include/asm/arch-mx6/mx6-ddr.h | 85 +
> arch/arm/include/asm/arch-mx6/mx6-pins.h | 31 +
> arch/arm/include/asm/arch-mx6/mx6dl-ddr.h | 71 +
> arch/arm/include/asm/arch-mx6/mx6dl_pins.h | 193 +--
> arch/arm/include/asm/arch-mx6/mx6q-ddr.h | 69 +
> arch/arm/include/asm/arch-mx6/mx6q_pins.h | 1671
> ++++++++++++++++++++
> arch/arm/include/asm/arch-mx6/mx6x_pins.h | 1671
> --------------------
> arch/arm/include/asm/arch-mx6/mxc_hdmi.h | 1083 ++++++-------
> arch/arm/include/asm/arch-mxs/dma.h | 19 +-
> arch/arm/include/asm/arch-mxs/imx-regs.h | 2 +
> arch/arm/include/asm/arch-mxs/iomux.h | 5 +
> arch/arm/include/asm/arch-mxs/regs-ssp.h | 26 +
> arch/arm/include/asm/arch-mxs/regs-timrot.h | 101 ++
> board/boundary/nitrogen6x/1066mhz_4x128mx16.cfg | 58 +
> board/boundary/nitrogen6x/1066mhz_4x256mx16.cfg | 58 +
> board/boundary/nitrogen6x/6x_bootscript.txt | 63 +
> .../boundary/nitrogen6x/6x_bootscript_android.txt | 64 +
> .../nitrogen6x/6x_bootscript_android_recovery.txt | 64 +
> board/boundary/nitrogen6x/6x_upgrade.txt | 45 +
> board/boundary/nitrogen6x/800mhz_2x128mx16.cfg | 58 +
> board/boundary/nitrogen6x/800mhz_2x256mx16.cfg | 58 +
> board/boundary/nitrogen6x/800mhz_4x128mx16.cfg | 57 +
> board/boundary/nitrogen6x/800mhz_4x256mx16.cfg | 58 +
> board/boundary/nitrogen6x/Makefile | 41 +
> board/boundary/nitrogen6x/README | 92 ++
> board/boundary/nitrogen6x/clocks.cfg | 46 +
> board/boundary/nitrogen6x/ddr-setup.cfg | 112 ++
> board/boundary/nitrogen6x/nitrogen6dl.cfg | 45 +
> board/boundary/nitrogen6x/nitrogen6dl2g.cfg | 45 +
> board/boundary/nitrogen6x/nitrogen6q.cfg | 45 +
> board/boundary/nitrogen6x/nitrogen6q2g.cfg | 45 +
> board/boundary/nitrogen6x/nitrogen6s.cfg | 45 +
> board/boundary/nitrogen6x/nitrogen6s1g.cfg | 45 +
> board/boundary/nitrogen6x/nitrogen6x.c | 895 +++++++++++
> board/denx/m28evk/m28evk.c | 4 +
> board/freescale/imx/ddr/mx6q_4x_mt41j128.cfg | 10 +-
> board/freescale/mx23evk/spl_boot.c | 10 +
> board/freescale/mx6qarm2/mx6qarm2.c | 78 +-
> board/freescale/mx6qsabreauto/mx6qsabreauto.c | 60 +-
> board/freescale/mx6qsabrelite/mx6qsabrelite.c | 292 ++--
> board/freescale/mx6qsabresd/mx6qsabresd.c | 102 +-
> board/olimex/mx23_olinuxino/mx23_olinuxino.c | 13 +
> board/olimex/mx23_olinuxino/spl_boot.c | 8 +
> boards.cfg | 6 +
> common/cmd_led.c | 6 +-
> common/cmd_sata.c | 2 +-
> drivers/mmc/mxsmmc.c | 20 +-
> drivers/spi/mxs_spi.c | 39 +-
> drivers/usb/host/ehci-mx6.c | 1 -
> drivers/usb/host/ehci-mxs.c | 155 +-
> include/configs/apx4devkit.h | 3 +-
> include/configs/m28evk.h | 5 +-
> include/configs/mx23_olinuxino.h | 64 +-
> include/configs/mx23evk.h | 14 +-
> include/configs/mx28evk.h | 4 +-
> include/configs/mx6_common.h | 23 +
> include/configs/mx6qarm2.h | 3 +
> include/configs/mx6qsabre_common.h | 4 +
> include/configs/mx6qsabrelite.h | 4 +
> include/configs/nitrogen6x.h | 285 ++++
> include/configs/sc_sps_1.h | 3 +-
> 77 files changed, 5683 insertions(+), 2758 deletions(-)
> delete mode 100644 arch/arm/cpu/armv7/mx6/lowlevel_init.S
> create mode 100644 arch/arm/include/asm/arch-mx6/mx6-ddr.h
> create mode 100644 arch/arm/include/asm/arch-mx6/mx6-pins.h
> create mode 100644 arch/arm/include/asm/arch-mx6/mx6dl-ddr.h
> create mode 100644 arch/arm/include/asm/arch-mx6/mx6q-ddr.h
> create mode 100644 arch/arm/include/asm/arch-mx6/mx6q_pins.h
> delete mode 100644 arch/arm/include/asm/arch-mx6/mx6x_pins.h
> create mode 100644 board/boundary/nitrogen6x/1066mhz_4x128mx16.cfg
> create mode 100644 board/boundary/nitrogen6x/1066mhz_4x256mx16.cfg
> create mode 100644 board/boundary/nitrogen6x/6x_bootscript.txt
> create mode 100644 board/boundary/nitrogen6x/6x_bootscript_android.txt
> create mode 100644
> board/boundary/nitrogen6x/6x_bootscript_android_recovery.txt
> create mode 100644 board/boundary/nitrogen6x/6x_upgrade.txt
> create mode 100644 board/boundary/nitrogen6x/800mhz_2x128mx16.cfg
> create mode 100644 board/boundary/nitrogen6x/800mhz_2x256mx16.cfg
> create mode 100644 board/boundary/nitrogen6x/800mhz_4x128mx16.cfg
> create mode 100644 board/boundary/nitrogen6x/800mhz_4x256mx16.cfg
> create mode 100644 board/boundary/nitrogen6x/Makefile
> create mode 100644 board/boundary/nitrogen6x/README
> create mode 100644 board/boundary/nitrogen6x/clocks.cfg
> create mode 100644 board/boundary/nitrogen6x/ddr-setup.cfg
> create mode 100644 board/boundary/nitrogen6x/nitrogen6dl.cfg
> create mode 100644 board/boundary/nitrogen6x/nitrogen6dl2g.cfg
> create mode 100644 board/boundary/nitrogen6x/nitrogen6q.cfg
> create mode 100644 board/boundary/nitrogen6x/nitrogen6q2g.cfg
> create mode 100644 board/boundary/nitrogen6x/nitrogen6s.cfg
> create mode 100644 board/boundary/nitrogen6x/nitrogen6s1g.cfg
> create mode 100644 board/boundary/nitrogen6x/nitrogen6x.c
> create mode 100644 include/configs/mx6_common.h
> create mode 100644 include/configs/nitrogen6x.h
>
>
> Best regards,
> Stefano
>
Applied to u-boot-arm/master, thanks!
Amicalement,
--
Albert.
More information about the U-Boot
mailing list