[U-Boot] [PATCH v2 3/4] arm, at91: add Siemens board taurus and axm
Andreas Bießmann
andreas.devel at googlemail.com
Mon Nov 4 09:43:15 CET 2013
On 11/04/2013 07:40 AM, Heiko Schocher wrote:
> enable support for the siemens AT91SAM9G20 based boards taurus
> and axm.
>
> Signed-off-by: Roger Meier <r.meier at siemens.com>
> Reviewed-by: Heiko Schocher <hs at denx.de>
> Cc: Andreas Bießmann <andreas.devel at googlemail.com>
> Cc: Bo Shen <voice.shen at atmel.com>
>
> ---
> - changes for v2:
> - add comments from bo shen
> - use gpio api
> - remove unneccessary comment
> - use at91_wait_for_reset()
> - remove unneccessary code in board file
> - Coding Style cleanup (tabs and unneccessary 1 after config define
> removed)
> - add commit message
> - add comments from Andreas Bießmann <andreas.devel at googlemail.com>:
> - detect sdram size on startup without read dram setting
> - get rid of MACH_TYPE definition in config file
> ---
> board/siemens/taurus/Makefile | 38 +++++++++
> board/siemens/taurus/taurus.c | 186 ++++++++++++++++++++++++++++++++++++++++++
> boards.cfg | 2 +
> include/configs/taurus.h | 159 ++++++++++++++++++++++++++++++++++++
> 4 files changed, 385 insertions(+)
> create mode 100644 board/siemens/taurus/Makefile
> create mode 100644 board/siemens/taurus/taurus.c
> create mode 100644 include/configs/taurus.h
>
> diff --git a/board/siemens/taurus/Makefile b/board/siemens/taurus/Makefile
> new file mode 100644
> index 0000000..9c288b7
> --- /dev/null
> +++ b/board/siemens/taurus/Makefile
> @@ -0,0 +1,38 @@
> +#
> +# Makefile for Siemens TAURUS (AT91SAM9G20) based board
> +# (C) Copyright 2013 Siemens AG
> +#
> +# Based on:
> +# U-Boot file: board/atmel/at91sam9260ek/Makefile
> +#
> +# (C) Copyright 2003-2008
> +# Wolfgang Denk, DENX Software Engineering, wd at denx.de.
> +#
> +# (C) Copyright 2008
> +# Stelian Pop <stelian at popies.net>
> +# Lead Tech Design <www.leadtechdesign.com>
> +#
> +# SPDX-License-Identifier: GPL-2.0+
> +#
> +
> +include $(TOPDIR)/config.mk
> +
> +LIB = $(obj)lib$(BOARD).o
> +
> +COBJS-y += taurus.o
> +
> +SRCS := $(SOBJS:.o=.S) $(COBJS-y:.o=.c)
> +OBJS := $(addprefix $(obj),$(COBJS-y))
> +SOBJS := $(addprefix $(obj),$(SOBJS))
> +
> +$(LIB): $(obj).depend $(OBJS) $(SOBJS)
> + $(call cmd_link_o_target, $(OBJS) $(SOBJS))
> +
> +#########################################################################
> +
> +# defines $(obj).depend target
> +include $(SRCTREE)/rules.mk
> +
> +sinclude $(obj).depend
> +
> +#########################################################################
> diff --git a/board/siemens/taurus/taurus.c b/board/siemens/taurus/taurus.c
> new file mode 100644
> index 0000000..66d55d6
> --- /dev/null
> +++ b/board/siemens/taurus/taurus.c
> @@ -0,0 +1,186 @@
> +/*
> + * Board functions for Siemens TAURUS (AT91SAM9G20) based boards
> + * (C) Copyright Siemens AG
> + *
> + * Based on:
> + * U-Boot file: board/atmel/at91sam9260ek/at91sam9260ek.c
> + *
> + * (C) Copyright 2007-2008
> + * Stelian Pop <stelian at popies.net>
> + * Lead Tech Design <www.leadtechdesign.com>
> + *
> + * SPDX-License-Identifier: GPL-2.0+
> + */
> +
> +#include <common.h>
> +#include <asm/io.h>
> +#include <asm/arch/at91sam9260_matrix.h>
> +#include <asm/arch/at91sam9_smc.h>
> +#include <asm/arch/at91_common.h>
> +#include <asm/arch/at91_pmc.h>
> +#include <asm/arch/at91_rstc.h>
> +#include <asm/arch/gpio.h>
> +#include <asm/arch/at91sam9_sdramc.h>
> +#include <atmel_mci.h>
> +
> +#if defined(CONFIG_RESET_PHY_R) && defined(CONFIG_MACB)
minor complaint: I think we can include net.h unconditionally here.
> +# include <net.h>
> +#endif
> +#include <netdev.h>
> +
> +DECLARE_GLOBAL_DATA_PTR;
> +
> +#ifdef CONFIG_CMD_NAND
> +static void taurus_nand_hw_init(void)
> +{
> + struct at91_smc *smc = (struct at91_smc *)ATMEL_BASE_SMC;
> + struct at91_matrix *matrix = (struct at91_matrix *)ATMEL_BASE_MATRIX;
> + unsigned long csa;
> +
> + /* Assign CS3 to NAND/SmartMedia Interface */
> + csa = readl(&matrix->ebicsa);
> + csa |= AT91_MATRIX_CS3A_SMC_SMARTMEDIA;
> + writel(csa, &matrix->ebicsa);
> +
> + /* Configure SMC CS3 for NAND/SmartMedia */
> + writel(AT91_SMC_SETUP_NWE(2) | AT91_SMC_SETUP_NCS_WR(0) |
> + AT91_SMC_SETUP_NRD(2) | AT91_SMC_SETUP_NCS_RD(0),
> + &smc->cs[3].setup);
> + writel(AT91_SMC_PULSE_NWE(4) | AT91_SMC_PULSE_NCS_WR(3) |
> + AT91_SMC_PULSE_NRD(4) | AT91_SMC_PULSE_NCS_RD(3),
> + &smc->cs[3].pulse);
> + writel(AT91_SMC_CYCLE_NWE(7) | AT91_SMC_CYCLE_NRD(7),
> + &smc->cs[3].cycle);
> + writel(AT91_SMC_MODE_RM_NRD | AT91_SMC_MODE_WM_NWE |
> + AT91_SMC_MODE_EXNW_DISABLE |
> + AT91_SMC_MODE_DBW_8 |
> + AT91_SMC_MODE_TDF_CYCLE(3),
> + &smc->cs[3].mode);
> +
> + /* Configure RDY/BSY */
> + at91_set_gpio_input(CONFIG_SYS_NAND_READY_PIN, 1);
> +
> + /* Enable NandFlash */
> + at91_set_gpio_output(CONFIG_SYS_NAND_ENABLE_PIN, 1);
> +}
> +#endif
> +
> +#ifdef CONFIG_MACB
> +static void taurus_macb_hw_init(void)
> +{
> + struct at91_pmc *pmc = (struct at91_pmc *)ATMEL_BASE_PMC;
> + struct at91_rstc *rstc = (struct at91_rstc *)ATMEL_BASE_RSTC;
> + unsigned long erstl;
> +
> + /* Enable EMAC clock */
> + writel(1 << ATMEL_ID_EMAC0, &pmc->pcer);
Is it required to enable the MACB clock before PHY reset? It will be
done later on in at91_macb_hw_init() in any case.
> +
> + /*
> + * Disable pull-up on:
> + * RXDV (PA17) => PHY normal mode (not Test mode)
> + * ERX0 (PA14) => PHY ADDR0
> + * ERX1 (PA15) => PHY ADDR1
> + * ERX2 (PA25) => PHY ADDR2
> + * ERX3 (PA26) => PHY ADDR3
> + * ECRS (PA28) => PHY ADDR4 => PHYADDR = 0x0
> + *
> + * PHY has internal pull-down
> + */
> + at91_set_pio_pullup(AT91_PIO_PORTA, 14, 0);
> + at91_set_pio_pullup(AT91_PIO_PORTA, 15, 0);
> + at91_set_pio_pullup(AT91_PIO_PORTA, 17, 0);
> + at91_set_pio_pullup(AT91_PIO_PORTA, 25, 0);
> + at91_set_pio_pullup(AT91_PIO_PORTA, 26, 0);
> + at91_set_pio_pullup(AT91_PIO_PORTA, 28, 0);
I'm a bit unhappy with this.
As sayed before I'd like to switch the 'ATMEL_LEGACY' PIO API to be the
new one. Would it be Ok for you to wait a few days for me to prepare the
API for all pio features to be able to feed with a single pin input?
Beside that I said to provide some PIO API with PORT + MASK input. I
still think that would be useful but I do not plan to work on that for
this release. I'd be happy if you could do that, but changing it later
is also Ok for me.
> +
> + /*
> + * Need to reset PHY ?-> 200us reset
> + * Bug within Atmel CPU (undefined initial states on io-lines)!
> + * Startup Ethernet Switch delayed so that hardstrap(Switch Config)
> + * has defined state after cold start (do not break daisy chain!).
> + */
> + if ((readl(&rstc->sr) & AT91_RSTC_RSTTYP) == AT91_RSTC_RSTTYP_GENERAL)
> + at91_set_gpio_output(AT91_PIN_PA25, 0);
> +
> +
One empty line could be left out.
> + erstl = readl(&rstc->mr) & AT91_RSTC_MR_ERSTL_MASK;
> +
> + /* Need to reset PHY -> 500ms reset */
> + writel(AT91_RSTC_KEY | AT91_RSTC_MR_ERSTL(13) |
> + AT91_RSTC_MR_URSTEN, &rstc->mr);
> +
> + writel(AT91_RSTC_KEY | AT91_RSTC_CR_EXTRST, &rstc->cr);
> +
> + /* Wait for end of reset */
> + at91_wait_for_reset(100);
> +
> + /* Restore NRST value */
> + writel(AT91_RSTC_KEY | erstl | AT91_RSTC_MR_URSTEN, &rstc->mr);
> +
> + at91_set_gpio_input(AT91_PIN_PA25, 1); /* ERST tri-state */
> +
> + /* Re-enable pull-up */
> + at91_set_pio_pullup(AT91_PIO_PORTA, 14, 1);
> + at91_set_pio_pullup(AT91_PIO_PORTA, 15, 1);
> + at91_set_pio_pullup(AT91_PIO_PORTA, 17, 1);
> + at91_set_pio_pullup(AT91_PIO_PORTA, 25, 1);
> + at91_set_pio_pullup(AT91_PIO_PORTA, 26, 1);
> + at91_set_pio_pullup(AT91_PIO_PORTA, 28, 1);
> +
> + /* Initialize EMAC=MACB hardware */
> + at91_macb_hw_init();
> +}
> +#endif
> +
> +#ifdef CONFIG_GENERIC_ATMEL_MCI
> +int board_mmc_init(bd_t *bd)
> +{
> + at91_mci_hw_init();
> +
> + return atmel_mci_init((void *)ATMEL_BASE_MCI);
> +}
> +#endif
> +
> +int board_early_init_f(void)
> +{
> + struct at91_pmc *pmc = (struct at91_pmc *)ATMEL_BASE_PMC;
> +
> + /* Enable clocks for all PIOs */
> + writel((1 << ATMEL_ID_PIOA) | (1 << ATMEL_ID_PIOB) |
> + (1 << ATMEL_ID_PIOC),
> + &pmc->pcer);
> +
> + return 0;
> +}
> +
> +int board_init(void)
> +{
> + /* adress of boot parameters */
> + gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100;
> +
> + at91_seriald_hw_init();
I think enabling debug output in early_init is more useful than here.
> +#ifdef CONFIG_CMD_NAND
> + taurus_nand_hw_init();
> +#endif
> +#ifdef CONFIG_MACB
> + taurus_macb_hw_init();
> +#endif
> +
> + return 0;
> +}
> +
> +int dram_init(void)
> +{
> + gd->ram_size = get_ram_size((void *)CONFIG_SYS_SDRAM_BASE,
> + CONFIG_SYS_SDRAM_SIZE);
> + return 0;
> +}
> +
> +int board_eth_init(bd_t *bis)
> +{
> + int rc = 0;
> +#ifdef CONFIG_MACB
> + rc = macb_eth_initialize(0, (void *)ATMEL_BASE_EMAC0, 0x00);
> +#endif
> + return rc;
> +}
> diff --git a/boards.cfg b/boards.cfg
> index aa2ee64..0fe98d0 100644
> --- a/boards.cfg
> +++ b/boards.cfg
> @@ -139,6 +139,8 @@ Active arm arm926ejs at91 ronetix pm9263
> Active arm arm926ejs at91 ronetix pm9g45 pm9g45 pm9g45:AT91SAM9G45 Ilko Iliev <iliev at ronetix.at>
> Active arm arm926ejs at91 taskit stamp9g20 portuxg20 stamp9g20:AT91SAM9G20,PORTUXG20 Markus Hubig <mhubig at imko.de>
> Active arm arm926ejs at91 taskit stamp9g20 stamp9g20 stamp9g20:AT91SAM9G20 Markus Hubig <mhubig at imko.de>
> +Active arm arm926ejs at91 siemens taurus axm taurus:AT91SAM9G20,MACH_TYPE=2068,BOARD_AXM Heiko Schocher <hs at denx.de>
> +Active arm arm926ejs at91 siemens taurus taurus taurus:AT91SAM9G20,MACH_TYPE=2067,BOARD_TAURUS Heiko Schocher <hs at denx.de>
> Active arm arm926ejs davinci ait cam_enc_4xx cam_enc_4xx cam_enc_4xx Heiko Schocher <hs at denx.de>
> Active arm arm926ejs davinci Barix ipam390 ipam390 - Heiko Schocher <hs at denx.de>
> Active arm arm926ejs davinci davinci da8xxevm da830evm - Nick Thompson <nick.thompson at gefanuc.com>
> diff --git a/include/configs/taurus.h b/include/configs/taurus.h
> new file mode 100644
> index 0000000..26255bb
> --- /dev/null
> +++ b/include/configs/taurus.h
> @@ -0,0 +1,159 @@
> +/*
> + * Common board functions for Siemens TAURUS (AT91SAM9G20) based boards
> + * (C) Copyright 2013 Siemens AG
> + *
> + * Based on:
> + * U-Boot file: include/configs/at91sam9260ek.h
> + *
> + * (C) Copyright 2007-2008
> + * Stelian Pop <stelian at popies.net>
> + * Lead Tech Design <www.leadtechdesign.com>
> + *
> + * SPDX-License-Identifier: GPL-2.0+
> + */
> +
> +#ifndef __CONFIG_H
> +#define __CONFIG_H
> +
> +/*
> + * SoC must be defined first, before hardware.h is included.
> + * In this case SoC is defined in boards.cfg.
> + */
> +#include <asm/hardware.h>
> +
> +#define MACH_TYPE_TAURUS 2067
> +#define MACH_TYPE_AXM 2068
> +
> +/*
> + * Warning: changing CONFIG_SYS_TEXT_BASE requires
> + * adapting the initial boot program.
> + * Since the linker has to swallow that define, we must use a pure
> + * hex number here!
> + */
> +
> +
> +#define CONFIG_SYS_TEXT_BASE 0x23f00000
> +
> +/* ARM asynchronous clock */
> +#define CONFIG_SYS_AT91_SLOW_CLOCK 32768 /* slow clock xtal */
> +#define CONFIG_SYS_AT91_MAIN_CLOCK 18432000 /* main clock xtal */
> +#define CONFIG_SYS_HZ 1000
> +
> +/* Misc CPU related */
> +#define CONFIG_ARCH_CPU_INIT
> +#define CONFIG_CMDLINE_TAG /* enable passing of ATAGs */
> +#define CONFIG_SETUP_MEMORY_TAGS
> +#define CONFIG_INITRD_TAG
> +#define CONFIG_SKIP_LOWLEVEL_INIT
> +#define CONFIG_BOARD_EARLY_INIT_F
> +#define CONFIG_DISPLAY_CPUINFO
> +
> +#define CONFIG_CMD_BOOTZ
> +#define CONFIG_OF_LIBFDT
> +
> +/* general purpose I/O */
> +#define CONFIG_ATMEL_LEGACY /* required until (g)pio is fixed */
> +#define CONFIG_AT91_GPIO
> +#define CONFIG_AT91_GPIO_PULLUP 1 /* keep pullups on peripheral pins */
> +
> +/* serial console */
> +#define CONFIG_ATMEL_USART
> +#define CONFIG_USART_BASE ATMEL_BASE_DBGU
> +#define CONFIG_USART_ID ATMEL_ID_SYS
> +#define CONFIG_BAUDRATE 115200
> +
> +#define CONFIG_BOOTDELAY 3
> +
> +/*
> + * Command line configuration.
> + */
> +#include <config_cmd_default.h>
> +#undef CONFIG_CMD_BDI
> +#undef CONFIG_CMD_FPGA
> +#undef CONFIG_CMD_IMI
> +#undef CONFIG_CMD_IMLS
> +#undef CONFIG_CMD_LOADS
> +#undef CONFIG_CMD_SOURCE
> +
> +#define CONFIG_CMD_PING
> +#define CONFIG_CMD_DHCP
> +#define CONFIG_CMD_NAND
> +
> +/*
> + * SDRAM: 1 bank, min 32, max 128 MB
> + * Initialized before u-boot gets started.
> + */
> +#define CONFIG_NR_DRAM_BANKS 1
> +#define CONFIG_SYS_SDRAM_BASE ATMEL_BASE_CS1
> +#define CONFIG_SYS_SDRAM_SIZE (128 * 1024 * 1024)
> +
> +/*
> + * Initial stack pointer: 4k - GENERATED_GBL_DATA_SIZE in internal SRAM,
> + * leaving the correct space for initial global data structure above
> + * that address while providing maximum stack area below.
> + */
> +# define CONFIG_SYS_INIT_SP_ADDR \
> + (ATMEL_BASE_SRAM1 + 0x1000 - GENERATED_GBL_DATA_SIZE)
> +
> +/* NAND flash */
> +#ifdef CONFIG_CMD_NAND
> +#define CONFIG_NAND_ATMEL
> +#define CONFIG_SYS_MAX_NAND_DEVICE 1
> +#define CONFIG_SYS_NAND_BASE ATMEL_BASE_CS3
> +#define CONFIG_SYS_NAND_DBW_8
> +#define CONFIG_SYS_NAND_MASK_ALE (1 << 21)
> +#define CONFIG_SYS_NAND_MASK_CLE (1 << 22)
> +#define CONFIG_SYS_NAND_ENABLE_PIN AT91_PIN_PC14
> +#define CONFIG_SYS_NAND_READY_PIN AT91_PIN_PC13
> +#endif
> +
> +/* NOR flash - no real flash on this board */
> +#define CONFIG_SYS_NO_FLASH 1
> +
> +/* Ethernet */
> +#define CONFIG_MACB
> +#define CONFIG_RMII
> +
> +/* USB */
> +#if defined(CONFIG_BOARD_TAURUS)
> +#define CONFIG_USB_ATMEL
> +#define CONFIG_USB_OHCI_NEW
> +#define CONFIG_SYS_USB_OHCI_CPU_INIT
> +#define CONFIG_SYS_USB_OHCI_REGS_BASE 0x00500000
> +#define CONFIG_SYS_USB_OHCI_SLOT_NAME "at91sam9260"
> +#define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS 2LEGA
What does '2LEGA' mean here?
> +#define CONFIG_USB_STORAGE
> +#endif
> +
> +/* load address */
> +#define CONFIG_SYS_LOAD_ADDR 0x22000000
> +
> +/* bootstrap in spi flash , u-boot + env + linux in nandflash */
> +#define CONFIG_ENV_IS_IN_NAND
> +#define CONFIG_ENV_OFFSET 0x100000
> +#define CONFIG_ENV_OFFSET_REDUND 0x180000
> +#define CONFIG_ENV_SIZE 0x20000 /* 1 sector = 128 kB */
> +#define CONFIG_BOOTCOMMAND "nand read 0x22000000 0x200000 0x300000; bootm"
> +#define CONFIG_BOOTARGS \
> + "console=ttyS0,115200 earlyprintk " \
> + "mtdparts=atmel_nand:256k(bootstrap)ro,512k(uboot)ro," \
> + "256k(env),256k(env_redundant),256k(spare)," \
> + "512k(dtb),6M(kernel)ro,-(rootfs) " \
> + "root=/dev/mtdblock7 rw rootfstype=jffs2"
> +
> +#define CONFIG_SYS_PROMPT "U-Boot> "
> +#define CONFIG_SYS_CBSIZE 256
> +#define CONFIG_SYS_MAXARGS 16
> +#define CONFIG_SYS_PBSIZE \
> + (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
> +#define CONFIG_SYS_LONGHELP
> +#define CONFIG_CMDLINE_EDITING
> +#define CONFIG_AUTO_COMPLETE
> +
> +/*
> + * Size of malloc() pool
> + */
> +#define CONFIG_SYS_MALLOC_LEN \
> + ROUND(3 * CONFIG_ENV_SIZE + 128*1024, 0x1000)
> +
> +#endif
>
Best regards
Andreas Bießmann
More information about the U-Boot
mailing list