[U-Boot] Pull request: u-boot-ti

Tom Rini trini at ti.com
Mon Nov 4 15:22:54 CET 2013


Hello,

The following changes since commit 304db0b38cfb04cfdb05a740d5ef27da06ea98ea:

  arm: Remove IXP425 boards pdnb3 and scpu (2013-10-17 09:28:08 +0200)

are available in the git repository at:

  git://git.denx.de/u-boot-ti.git master

for you to fetch changes up to f6723794fd8f3362c4f3b5d0f36607a6a6f107b2:

  TI:omap5: Add rdaddr, use consistent loadaddr values (2013-11-01 15:56:00 -0400)

----------------------------------------------------------------
Andreas Bießmann (10):
      tricorder: update flash partitioning
      tricorder: use generic provided loadaddr
      tricorder: add configuration for a flashcard u-boot
      tricorder: add cmdline history
      tricorder: add mtdparts to environment
      tricorder: add tricordereeprom command
      tricorder: panic() on unknown board
      tricorder: add led support
      tricorder: read kernel directly from NAND
      tricorder: support 256MiB SDRAM on revision > D

Heiko Schocher (2):
      nand, davinci: add special UBL ecc position
      arm, da85x: update for the ipam390 board

Igor Grinberg (2):
      cm-t35: move the eeprom code to common place
      cm-t35: move the display code to common place

Javier Martinez Canillas (2):
      ARM: IGEP0033: rename config file to am335x_igep0033.h
      OMAP3: igep00x0: rename config file to omap3_igep00x0.h

Lokesh Vutla (1):
      ARM: OMAP4: Convert to ti_armv7_common.h

Minal Shah (1):
      dra7xx_evm: Enabled UART-boot mode and add dra7xx_evm_uart3 build

Nikita Kiryanov (3):
      cm_t35: reduce default bootdelay to 3 seconds
      cm_t35: turn on GPIO commands
      cm_t35: update lcd predefines

SRICHARAN R (1):
      ARM: OMAP5: DDR3: Change io settings

Thomas Weber (3):
      tricorder: remove lcdmode from bootargs
      tricorder: Make u-boot faster
      tricorder: switch to alternative memtest

Tom Rini (7):
      drivers/rtc/davinci.c: Reference DAVINCI_RTC_BASE more directly
      am33xx, davinci: Create and use <asm/davinci_rtc.h>
      bootcount_davinci: Switch to scratch register #2
      TI:am33xx: Add bootcount support to ti_am335x_common.h
      am335x: Enable CONFIG_OMAP_WATCHDOG support
      TI:armv7: Change CONFIG_SYS_SPL_ARGS_ADDR to a higher address
      TI:omap5: Add rdaddr, use consistent loadaddr values

 arch/arm/cpu/armv7/am33xx/board.c                  |    7 +-
 arch/arm/cpu/armv7/omap-common/boot-common.c       |    4 +
 arch/arm/include/asm/arch-am33xx/cpu.h             |    9 -
 arch/arm/include/asm/arch-davinci/hardware.h       |   38 ---
 arch/arm/include/asm/arch-omap5/omap.h             |    4 +-
 arch/arm/include/asm/arch-omap5/spl.h              |    1 +
 arch/arm/include/asm/davinci_rtc.h                 |   52 ++++
 board/Barix/ipam390/ipam390-ais-uart.cfg           |    2 +-
 board/Barix/ipam390/ipam390.c                      |   29 +--
 board/compulab/cm_t35/Makefile                     |    3 -
 board/compulab/cm_t35/cm_t35.c                     |    7 +-
 board/compulab/common/Makefile                     |   36 +++
 board/compulab/{cm_t35 => common}/eeprom.c         |   51 ++--
 board/compulab/{cm_t35 => common}/eeprom.h         |    8 +-
 .../{cm_t35/display.c => common/omap3_display.c}   |    8 +-
 board/corscience/tricorder/Makefile                |    2 +-
 board/corscience/tricorder/led.c                   |   80 +++++++
 board/corscience/tricorder/tricorder-eeprom.c      |  251 ++++++++++++++++++++
 board/corscience/tricorder/tricorder-eeprom.h      |   41 ++++
 board/corscience/tricorder/tricorder.c             |  126 +++++++++-
 board/corscience/tricorder/tricorder.h             |    4 +-
 board/enbw/enbw_cmc/enbw_cmc.c                     |    1 +
 board/ti/am335x/board.c                            |    6 +
 boards.cfg                                         |   16 +-
 drivers/bootcount/Makefile                         |    1 +
 drivers/bootcount/bootcount_davinci.c              |   13 +-
 drivers/mtd/nand/davinci_nand.c                    |   12 +
 drivers/rtc/davinci.c                              |    8 +-
 include/configs/{igep0033.h => am335x_igep0033.h}  |    0
 include/configs/cm_t35.h                           |    3 +-
 include/configs/dra7xx_evm.h                       |    9 +-
 include/configs/ipam390.h                          |   35 ++-
 include/configs/{igep00x0.h => omap3_igep00x0.h}   |    0
 include/configs/omap4_common.h                     |  188 +++------------
 include/configs/omap4_panda.h                      |    2 -
 include/configs/omap4_sdp4430.h                    |    2 -
 include/configs/omap5_common.h                     |    7 +-
 include/configs/ti_am335x_common.h                 |   14 ++
 include/configs/ti_armv7_common.h                  |    2 +-
 include/configs/tricorder.h                        |  155 +++++++++---
 40 files changed, 876 insertions(+), 361 deletions(-)
 create mode 100644 arch/arm/include/asm/davinci_rtc.h
 create mode 100644 board/compulab/common/Makefile
 rename board/compulab/{cm_t35 => common}/eeprom.c (60%)
 rename board/compulab/{cm_t35 => common}/eeprom.h (62%)
 rename board/compulab/{cm_t35/display.c => common/omap3_display.c} (97%)
 create mode 100644 board/corscience/tricorder/led.c
 create mode 100644 board/corscience/tricorder/tricorder-eeprom.c
 create mode 100644 board/corscience/tricorder/tricorder-eeprom.h
 rename include/configs/{igep0033.h => am335x_igep0033.h} (100%)
 rename include/configs/{igep00x0.h => omap3_igep00x0.h} (100%)

Thanks!

-- 
Tom
-------------- next part --------------
A non-text attachment was scrubbed...
Name: not available
Type: application/pgp-signature
Size: 836 bytes
Desc: Digital signature
URL: <http://lists.denx.de/pipermail/u-boot/attachments/20131104/80d6e6fa/attachment.pgp>


More information about the U-Boot mailing list