[U-Boot] [PATCH 10/34] spi: Add zynq qspi controller driver
Dinh Nguyen
dinh.linux at gmail.com
Wed Nov 6 06:02:26 CET 2013
On 11/5/13 11:46 AM, Jagannadha Sutradharudu Teki wrote:
> Zynq qspi controller driver supports single bus
> with singe chipselect.
>
> Zynq qspi can be operated in below connection modes
> - single qspi
> - dual qspi, with dual stacked
> - dual qspi, with dual parallel
>
> Signed-off-by: Jagannadha Sutradharudu Teki <jaganna at xilinx.com>
> ---
> arch/arm/include/asm/arch-zynq/hardware.h | 1 +
> drivers/spi/Makefile | 1 +
> drivers/spi/zynq_qspi.c | 447 ++++++++++++++++++++++++++++++
> 3 files changed, 449 insertions(+)
> create mode 100644 drivers/spi/zynq_qspi.c
>
> diff --git a/arch/arm/include/asm/arch-zynq/hardware.h b/arch/arm/include/asm/arch-zynq/hardware.h
> index cd69677..05870ae 100644
> --- a/arch/arm/include/asm/arch-zynq/hardware.h
> +++ b/arch/arm/include/asm/arch-zynq/hardware.h
> @@ -19,6 +19,7 @@
> #define ZYNQ_I2C_BASEADDR1 0xE0005000
> #define ZYNQ_SPI_BASEADDR0 0xE0006000
> #define ZYNQ_SPI_BASEADDR1 0xE0007000
> +#define ZYNQ_QSPI_BASEADDR 0xE000D000
> #define ZYNQ_DDRC_BASEADDR 0xF8006000
>
> /* Reflect slcr offsets */
> diff --git a/drivers/spi/Makefile b/drivers/spi/Makefile
> index 27902fe..5fafee0 100644
> --- a/drivers/spi/Makefile
> +++ b/drivers/spi/Makefile
> @@ -37,3 +37,4 @@ obj-$(CONFIG_TEGRA114_SPI) += tegra114_spi.o
> obj-$(CONFIG_TI_QSPI) += ti_qspi.o
> obj-$(CONFIG_XILINX_SPI) += xilinx_spi.o
> obj-$(CONFIG_ZYNQ_SPI) += zynq_spi.o
> +obj-$(CONFIG_ZYNQ_QSPI) += zynq_qspi.o
> diff --git a/drivers/spi/zynq_qspi.c b/drivers/spi/zynq_qspi.c
> new file mode 100644
> index 0000000..f38ebca
> --- /dev/null
> +++ b/drivers/spi/zynq_qspi.c
> @@ -0,0 +1,447 @@
> +/*
> + * (C) Copyright 2013 Xilinx, Inc.
> + *
> + * Zynq PS Quad-SPI(QSPI) controller driver (master mode only)
> + *
> + * SPDX-License-Identifier: GPL-2.0+
> + */
> +
> +#include <config.h>
> +#include <common.h>
> +#include <malloc.h>
> +#include <spi.h>
> +#include <asm/io.h>
> +#include <asm/arch/hardware.h>
> +
> +/* zynq spi register bit masks ZYNQ_QSPI_<REG>_<BIT>_MASK */
> +#define ZYNQ_QSPI_CR_IFMODE_MASK (1 << 31) /* Flash intrface mode*/
> +#define ZYNQ_QSPI_CR_MSA_MASK (1 << 15) /* Manual start enb */
> +#define ZYNQ_QSPI_CR_MCS_MASK (1 << 14) /* Manual chip select */
> +#define ZYNQ_QSPI_CR_PCS_MASK (1 << 10) /* Peri chip select */
> +#define ZYNQ_QSPI_CR_FW_MASK (0x3 << 6) /* FIFO width */
> +#define ZYNQ_QSPI_CR_BRD_MASK (0x7 << 3) /* Baud rate div */
> +#define ZYNQ_QSPI_CR_CPHA_MASK (1 << 2) /* Clock phase */
> +#define ZYNQ_QSPI_CR_CPOL_MASK (1 << 1) /* Clock polarity */
> +#define ZYNQ_QSPI_CR_MSTREN_MASK (1 << 0) /* Mode select */
> +#define ZYNQ_QSPI_IXR_RXNEMPTY_MASK (1 << 4) /* RX_FIFO_not_empty */
> +#define ZYNQ_QSPI_IXR_TXOW_MASK (1 << 2) /* TX_FIFO_not_full */
> +#define ZYNQ_QSPI_IXR_ALL_MASK 0x7F /* All IXR bits */
> +#define ZYNQ_QSPI_ENR_SPI_EN_MASK (1 << 0) /* SPI Enable */
> +
> +/* QSPI Transmit Data Register */
> +#define ZYNQ_QSPI_TXD_00_00_OFFSET 0x1C /* Transmit 4-byte inst */
> +#define ZYNQ_QSPI_TXD_00_01_OFFSET 0x80 /* Transmit 1-byte inst */
> +#define ZYNQ_QSPI_TXD_00_10_OFFSET 0x84 /* Transmit 2-byte inst */
> +#define ZYNQ_QSPI_TXD_00_11_OFFSET 0x88 /* Transmit 3-byte inst */
> +
> +/* Definitions of the flash commands - Flash insts in ascending order */
> +#define ZYNQ_QSPI_FLASH_INST_WRSR 0x01 /* Write status register */
> +#define ZYNQ_QSPI_FLASH_INST_PP 0x02 /* Page program */
> +#define ZYNQ_QSPI_FLASH_INST_WRDS 0x04 /* Write disable */
> +#define ZYNQ_QSPI_FLASH_INST_RDSR1 0x05 /* Read status register 1 */
> +#define ZYNQ_QSPI_FLASH_INST_WREN 0x06 /* Write enable */
> +#define ZYNQ_QSPI_FLASH_INST_AFR 0x0B /* Fast read data bytes */
> +#define ZYNQ_QSPI_FLASH_INST_BE_4K 0x20 /* Erase 4KiB block */
> +#define ZYNQ_QSPI_FLASH_INST_RDSR2 0x35 /* Read status register 2 */
> +#define ZYNQ_QSPI_FLASH_INST_BE_32K 0x52 /* Erase 32KiB block */
> +#define ZYNQ_QSPI_FLASH_INST_RDID 0x9F /* Read JEDEC ID */
> +#define ZYNQ_QSPI_FLASH_INST_SE 0xD8 /* Sector erase (usually 64KB)*/
> +
> +#define ZYNQ_QSPI_FIFO_DEPTH 63
> +#ifndef CONFIG_SYS_ZYNQ_QSPI_WAIT
> +#define CONFIG_SYS_ZYNQ_QSPI_WAIT CONFIG_SYS_HZ/100 /* 10 ms */
> +#endif
> +
> +/* zynq qspi register set */
> +struct zynq_qspi_regs {
> + u32 cr; /* 0x00 */
> + u32 isr; /* 0x04 */
> + u32 ier; /* 0x08 */
> + u32 idr; /* 0x0C */
> + u32 imr; /* 0x10 */
> + u32 enr; /* 0x14 */
> + u32 dr; /* 0x18 */
> + u32 txd0r; /* 0x1C */
> + u32 rxdr; /* 0x20 */
> + u32 sicr; /* 0x24 */
> + u32 txftr; /* 0x28 */
> + u32 rxftr; /* 0x2C */
> + u32 gpior; /* 0x30 */
> + u32 reserved0[19];
> + u32 txd1r; /* 0x80 */
> + u32 txd2r; /* 0x84 */
> + u32 txd3r; /* 0x88 */
> +};
> +
> +/*
> + * struct zynq_qspi_inst_format - Defines qspi flash instruction format
> + * @inst: Instruction code
> + * @inst_size: Size of the instruction including address bytes
> + * @inst_off: Register address where instruction has to be written
> + */
> +struct zynq_qspi_inst_format {
> + u8 inst;
> + u8 inst_size;
> + u8 inst_off;
> +};
> +
> +/* List of all the QSPI instructions and its format */
> +static struct zynq_qspi_inst_format flash_inst[] = {
> + {ZYNQ_QSPI_FLASH_INST_WRSR, 1, ZYNQ_QSPI_TXD_00_01_OFFSET},
> + {ZYNQ_QSPI_FLASH_INST_PP, 4, ZYNQ_QSPI_TXD_00_00_OFFSET},
> + {ZYNQ_QSPI_FLASH_INST_WRDS, 1, ZYNQ_QSPI_TXD_00_01_OFFSET},
> + {ZYNQ_QSPI_FLASH_INST_RDSR1, 1, ZYNQ_QSPI_TXD_00_01_OFFSET},
> + {ZYNQ_QSPI_FLASH_INST_WREN, 1, ZYNQ_QSPI_TXD_00_01_OFFSET},
> + {ZYNQ_QSPI_FLASH_INST_AFR, 1, ZYNQ_QSPI_TXD_00_01_OFFSET},
> + {ZYNQ_QSPI_FLASH_INST_BE_4K, 4, ZYNQ_QSPI_TXD_00_00_OFFSET},
> + {ZYNQ_QSPI_FLASH_INST_RDSR2, 1, ZYNQ_QSPI_TXD_00_01_OFFSET},
> + {ZYNQ_QSPI_FLASH_INST_BE_32K, 4, ZYNQ_QSPI_TXD_00_00_OFFSET},
> + {ZYNQ_QSPI_FLASH_INST_RDID, 1, ZYNQ_QSPI_TXD_00_01_OFFSET},
> + {ZYNQ_QSPI_FLASH_INST_SE, 4, ZYNQ_QSPI_TXD_00_00_OFFSET},
> + /* Add all the instructions supported by the flash device */
> +};
> +
> +/* zynq spi slave */
> +struct zynq_qspi_slave {
> + struct spi_slave slave;
> + struct zynq_qspi_regs *base;
> + u8 mode;
> + u8 is_inst;
> + u8 fifo_depth;
> + const void *tx_buf;
> + void *rx_buf;
> + u32 tx_len;
> + u32 rx_len;
> + u32 speed_hz;
> + u32 input_hz;
> + u32 req_hz;
> +};
> +
> +static inline struct zynq_qspi_slave *to_zynq_qspi_slave(
> + struct spi_slave *slave)
> +{
> + return container_of(slave, struct zynq_qspi_slave, slave);
> +}
> +
> +static void zynq_qspi_init_hw(struct zynq_qspi_slave *zslave)
> +{
> + u32 confr;
> +
> + /* Disable SPI */
> + writel(~ZYNQ_QSPI_ENR_SPI_EN_MASK, &zslave->base->enr);
> +
> + /* Disable Interrupts */
> + writel(ZYNQ_QSPI_IXR_ALL_MASK, &zslave->base->idr);
> +
> + /* Clear RX FIFO */
> + while (readl(&zslave->base->isr) &
> + ZYNQ_QSPI_IXR_RXNEMPTY_MASK)
> + readl(&zslave->base->rxdr);
> +
> + /* Clear Interrupts */
> + writel(ZYNQ_QSPI_IXR_ALL_MASK, &zslave->base->isr);
> +
> + /* Manual slave select and Auto start */
> + confr = ZYNQ_QSPI_CR_IFMODE_MASK | ZYNQ_QSPI_CR_MCS_MASK |
> + ZYNQ_QSPI_CR_PCS_MASK | ZYNQ_QSPI_CR_FW_MASK |
> + ZYNQ_QSPI_CR_MSTREN_MASK;
> + confr &= ~ZYNQ_QSPI_CR_MSA_MASK;
> + confr &= ~ZYNQ_QSPI_CR_MSA_MASK;
Copy/paste error? Why "confr &= ~ZYNQ_QSPI_CR_MSA_MASK;" twice?
> + writel(confr, &zslave->base->cr);
> +
> + /* Enable SPI */
> + writel(ZYNQ_QSPI_ENR_SPI_EN_MASK, &zslave->base->enr);
> +}
> +
> +/*
> + * zynq_qspi_read - Copy data to RX buffer
> + * @zqspi: Pointer to zynq_qspi_slave
> + * @data: The 32 bit variable where data is stored
> + * @size: Number of bytes to be copied from data to RX buffer
> + */
> +static void zynq_qspi_read(struct zynq_qspi_slave *zslave, u32 data, u8 size)
> +{
> + if (zslave->rx_buf) {
> + data >>= (4 - size) * 8;
> + data = le32_to_cpu(data);
> + memcpy((u8 *)zslave->rx_buf, &data, size);
> + zslave->rx_buf += size;
> + }
> +
> + zslave->rx_len -= size;
> +}
> +
> +/*
> + * zynq_qspi_write - Copy data from TX buffer
> + * @zslave: Pointer to zynq_qspi_slave
> + * @data: Pointer to the 32 bit variable where data is to be copied
> + * @size: Number of bytes to be copied from TX buffer to data
> + */
> +static void zynq_qspi_write(struct zynq_qspi_slave *zslave, u32 *data, u8 size)
> +{
> + if (zslave->tx_buf) {
> + switch (size) {
> + case 1:
> + *data = *((u8 *)zslave->tx_buf);
> + zslave->tx_buf += 1;
> + *data |= 0xFFFFFF00;
> + break;
> + case 2:
> + *data = *((u16 *)zslave->tx_buf);
> + zslave->tx_buf += 2;
> + *data |= 0xFFFF0000;
> + break;
> + case 3:
> + *data = *((u16 *)zslave->tx_buf);
> + zslave->tx_buf += 2;
> + *data |= (*((u8 *)zslave->tx_buf) << 16);
> + zslave->tx_buf += 1;
> + *data |= 0xFF000000;
> + break;
> + case 4:
> + /* Can not assume word aligned buffer */
> + memcpy(data, zslave->tx_buf, size);
> + zslave->tx_buf += 4;
> + break;
> + default:
> + /* This will never execute */
> + break;
> + }
> + } else {
> + *data = 0;
> + }
> +
> + zslave->tx_len -= size;
> +}
> +
> +static int zynq_qspi_check_txfifo(struct zynq_qspi_slave *zslave)
> +{
> + u32 ts, status;
> +
> + ts = get_timer(0);
> + status = readl(&zslave->base->isr);
> + while (!(status & ZYNQ_QSPI_IXR_TXOW_MASK)) {
> + if (get_timer(ts) > CONFIG_SYS_ZYNQ_QSPI_WAIT) {
> + printf("spi_xfer: Timeout! TX FIFO not full\n");
> + return -1;
> + }
> + status = readl(&zslave->base->isr);
> + }
> +
> + return 0;
> +}
> +
> +static int zynq_qspi_process_tx(struct zynq_qspi_slave *zslave)
> +{
> + struct zynq_qspi_inst_format *curr_inst;
> + u8 inst, index;
> + u32 buf;
> +
> + inst = *(u8 *)zslave->tx_buf;
> + /* instuction */
> + if (inst && zslave->is_inst) {
> + for (index = 0; index < ARRAY_SIZE(flash_inst); index++)
> + if (inst == flash_inst[index].inst)
> + break;
> +
> + if (index == ARRAY_SIZE(flash_inst)) {
> + printf("spi_xfer: Unsupported inst %02x\n", inst);
> + return -1;
> + }
> +
> + curr_inst = &flash_inst[index];
> + debug("spi_xfer: inst:%02x inst_size:%d inst_off:%02x\n",
> + curr_inst->inst, curr_inst->inst_size,
> + curr_inst->inst_off);
> +
> + zynq_qspi_write(zslave, &buf, curr_inst->inst_size);
> + writel(buf, &zslave->base->cr + (curr_inst->inst_off / 4));
> + zslave->is_inst = 0;
> + } else if (!zslave->is_inst) { /* addr + data */
> + if (zslave->tx_len < 4) {
> + /* Check TXOW for txd1, txd2 and txd3 */
> + if (zynq_qspi_check_txfifo(zslave) < 0)
> + return -1;
> +
> + zynq_qspi_write(zslave, &buf, zslave->tx_len);
> + writel(buf,
> + &zslave->base->txd1r + (zslave->tx_len - 1));
> + } else {
> + zynq_qspi_write(zslave, &buf, 4);
> + writel(buf, &zslave->base->txd0r);
> + }
> + }
> +
> + return 0;
> +}
> +
> +int spi_cs_is_valid(unsigned int bus, unsigned int cs)
> +{
> + /* 1 bus with 1 chipselect */
> + return bus < 1 && cs < 1;
> +}
> +
> +void spi_cs_activate(struct spi_slave *slave)
> +{
> + struct zynq_qspi_slave *zslave = to_zynq_qspi_slave(slave);
> +
> + debug("spi_cs_activate: 0x%08x\n", (u32)slave);
> + clrbits_le32(&zslave->base->cr, ZYNQ_QSPI_CR_PCS_MASK);
> +
> + zslave->is_inst = 1;
> +}
> +
> +void spi_cs_deactivate(struct spi_slave *slave)
> +{
> + struct zynq_qspi_slave *zslave = to_zynq_qspi_slave(slave);
> +
> + debug("spi_cs_deactivate: 0x%08x\n", (u32)slave);
> + setbits_le32(&zslave->base->cr, ZYNQ_QSPI_CR_PCS_MASK);
> +
> + zslave->is_inst = 0;
> +}
> +
> +void spi_init()
> +{
> + /* nothing to do */
> +}
> +
> +struct spi_slave *spi_setup_slave(unsigned int bus, unsigned int cs,
> + unsigned int max_hz, unsigned int mode)
> +{
> + struct zynq_qspi_slave *zslave;
> +
> + if (!spi_cs_is_valid(bus, cs))
> + return NULL;
> +
> + zslave = spi_alloc_slave(struct zynq_qspi_slave, bus, cs);
> + if (!zslave) {
> + printf("SPI_error: Fail to allocate zynq_qspi_slave\n");
> + return NULL;
> + }
> +
> + zslave->base = (struct zynq_qspi_regs *)ZYNQ_QSPI_BASEADDR;
> + zslave->mode = mode;
> + zslave->fifo_depth = ZYNQ_QSPI_FIFO_DEPTH;
> + zslave->input_hz = 200000000;
Should 200000000 be a CONFIG define?
Dinh
> + zslave->speed_hz = zslave->input_hz / 2;
> + zslave->req_hz = max_hz;
> +
> + /* init the zynq spi hw */
> + zynq_qspi_init_hw(zslave);
> +
> + return &zslave->slave;
> +}
> +
> +void spi_free_slave(struct spi_slave *slave)
> +{
> + struct zynq_qspi_slave *zslave = to_zynq_qspi_slave(slave);
> +
> + debug("spi_free_slave: 0x%08x\n", (u32)slave);
> + free(zslave);
> +}
> +
> +int spi_claim_bus(struct spi_slave *slave)
> +{
> + struct zynq_qspi_slave *zslave = to_zynq_qspi_slave(slave);
> + u32 confr = 0;
> + u8 baud_rate_val = 0;
> +
> + writel(~ZYNQ_QSPI_ENR_SPI_EN_MASK, &zslave->base->enr);
> +
> + /* Set the SPI Clock phase and polarities */
> + confr = readl(&zslave->base->cr);
> + confr &= ~(ZYNQ_QSPI_CR_CPHA_MASK | ZYNQ_QSPI_CR_CPOL_MASK);
> + if (zslave->mode & SPI_CPHA)
> + confr |= ZYNQ_QSPI_CR_CPHA_MASK;
> + if (zslave->mode & SPI_CPOL)
> + confr |= ZYNQ_QSPI_CR_CPOL_MASK;
> +
> + /* Set the clock frequency */
> + if (zslave->req_hz == 0) {
> + /* Set baudrate x8, if the req_hz is 0 */
> + baud_rate_val = 0x2;
> + } else if (zslave->speed_hz != zslave->req_hz) {
> + while ((baud_rate_val < 8) &&
> + ((zslave->input_hz /
> + (2 << baud_rate_val)) > zslave->req_hz))
> + baud_rate_val++;
> + zslave->speed_hz = zslave->req_hz / (2 << baud_rate_val);
> + }
> + confr &= ~ZYNQ_QSPI_CR_BRD_MASK;
> + confr |= (baud_rate_val << 3);
> + writel(confr, &zslave->base->cr);
> +
> + writel(ZYNQ_QSPI_ENR_SPI_EN_MASK, &zslave->base->enr);
> +
> + return 0;
> +}
> +
> +void spi_release_bus(struct spi_slave *slave)
> +{
> + struct zynq_qspi_slave *zslave = to_zynq_qspi_slave(slave);
> +
> + debug("spi_release_bus: 0x%08x\n", (u32)slave);
> + writel(~ZYNQ_QSPI_ENR_SPI_EN_MASK, &zslave->base->enr);
> +}
> +
> +int spi_xfer(struct spi_slave *slave, unsigned int bitlen, const void *dout,
> + void *din, unsigned long flags)
> +{
> + struct zynq_qspi_slave *zslave = to_zynq_qspi_slave(slave);
> + u32 len = bitlen / 8, tx_tvl;
> + u32 buf, status;
> +
> + debug("spi_xfer: bus:%i cs:%i bitlen:%i len:%i flags:%lx\n",
> + slave->bus, slave->cs, bitlen, len, flags);
> +
> + if (bitlen == 0)
> + return -1;
> +
> + if (bitlen % 8) {
> + debug("spi_xfer: Non byte aligned SPI transfer\n");
> + return -1;
> + }
> +
> + if (flags & SPI_XFER_BEGIN)
> + spi_cs_activate(slave);
> +
> + zslave->tx_len = len;
> + zslave->rx_len = len;
> + zslave->tx_buf = dout;
> + zslave->rx_buf = din;
> + while (zslave->rx_len > 0) {
> + /* Write the data into TX FIFO - tx threshold is fifo_depth */
> + tx_tvl = 0;
> + while ((tx_tvl < zslave->fifo_depth) && zslave->tx_len) {
> + if (zynq_qspi_process_tx(zslave) < 0) {
> + flags |= SPI_XFER_END;
> + goto out;
> + }
> + tx_tvl++;
> + }
> +
> + /* Check TX FIFO completion */
> + if (zynq_qspi_check_txfifo(zslave) < 0) {
> + flags |= SPI_XFER_END;
> + goto out;
> + }
> +
> + /* Read the data from RX FIFO */
> + status = readl(&zslave->base->isr);
> + while (status & ZYNQ_QSPI_IXR_RXNEMPTY_MASK) {
> + buf = readl(&zslave->base->rxdr);
> + if (zslave->rx_len < 4)
> + zynq_qspi_read(zslave, buf, zslave->rx_len);
> + else
> + zynq_qspi_read(zslave, buf, 4);
> + status = readl(&zslave->base->isr);
> + }
> + }
> +
> +out:
> + if (flags & SPI_XFER_END)
> + spi_cs_deactivate(slave);
> +
> + return 0;
> +}
More information about the U-Boot
mailing list