[U-Boot] [PATCH] ARM: imx6: Add Bachmann electronic ot1205 mr board
Stefano Babic
sbabic at denx.de
Wed Nov 6 17:51:08 CET 2013
Hi Christian,
On 06/11/2013 13:51, Christian Gmeiner wrote:
> Add basic support for the Bachmann electronic ot1205 board. It
> is powered by an imx6d and will come in different flavours. This
> patch adds support for the mr flavour. It has a front panel with
> some LEDs and some keys.
Maybe it helps if you add here a short list of peripheral that are
supported. From code, I see at least SDHC and ethernet.
> diff --git a/board/bachmann/ot1205/ot1205.c b/board/bachmann/ot1205/ot1205.c
> new file mode 100644
> index 0000000..37c6159
> --- /dev/null
> +++ b/board/bachmann/ot1205/ot1205.c
> @@ -0,0 +1,236 @@
> +/*
> + * Copyright (C) 2010-2013 Freescale Semiconductor, Inc.
> + * Copyright (C) 2013, Bachmann electronic GmbH
> + *
> + * SPDX-License-Identifier: GPL-2.0+
> + */
> +
> +#include <common.h>
> +#include <asm/io.h>
> +#include <asm/arch/clock.h>
> +#include <asm/arch/imx-regs.h>
> +#include <asm/arch/iomux.h>
> +#include <asm/arch/sys_proto.h>
> +#include <malloc.h>
> +#include <asm/arch/mx6-pins.h>
> +#include <asm/errno.h>
> +#include <asm/gpio.h>
> +#include <asm/imx-common/iomux-v3.h>
> +#include <asm/imx-common/mxc_i2c.h>
> +#include <asm/imx-common/boot_mode.h>
> +#include <mmc.h>
> +#include <fsl_esdhc.h>
> +#include <micrel.h>
> +#include <miiphy.h>
> +#include <netdev.h>
> +#include <asm/arch/crm_regs.h>
> +#include <i2c.h>
> +#include <pca953x.h>
> +
> +DECLARE_GLOBAL_DATA_PTR;
> +
> +#define UART_PAD_CTRL (PAD_CTL_PUS_100K_UP | \
> + PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | \
> + PAD_CTL_SRE_FAST | PAD_CTL_HYS)
> +
> +#define USDHC_PAD_CTRL (PAD_CTL_PUS_47K_UP | \
> + PAD_CTL_SPEED_LOW | PAD_CTL_DSE_80ohm | \
> + PAD_CTL_SRE_FAST | PAD_CTL_HYS)
> +
> +#define ENET_PAD_CTRL (PAD_CTL_PUS_100K_UP | \
> + PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | PAD_CTL_HYS)
> +
> +#define SPI_PAD_CTRL (PAD_CTL_HYS | PAD_CTL_SPEED_MED | \
> + PAD_CTL_DSE_40ohm | PAD_CTL_SRE_FAST)
> +
> +#define I2C_PAD_CTRL (PAD_CTL_PUS_100K_UP | \
> + PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | PAD_CTL_HYS | \
> + PAD_CTL_ODE | PAD_CTL_SRE_FAST)
> +
> +#define OUTPUT_40OHM (PAD_CTL_SPEED_MED|PAD_CTL_DSE_40ohm)
> +
> +int dram_init(void)
> +{
> + gd->ram_size = get_ram_size((void *)PHYS_SDRAM, PHYS_SDRAM_SIZE);
> +
> + return 0;
> +}
> +
> +iomux_v3_cfg_t const uart1_pads[] = {
> + MX6_PAD_CSI0_DAT10__UART1_TXD | MUX_PAD_CTRL(UART_PAD_CTRL),
> + MX6_PAD_CSI0_DAT11__UART1_RXD | MUX_PAD_CTRL(UART_PAD_CTRL),
> +};
> +
> +
> +static void setup_iomux_uart(void)
> +{
> + imx_iomux_v3_setup_multiple_pads(uart1_pads,
> + ARRAY_SIZE(uart1_pads));
> +}
> +
> +int board_early_init_f(void)
> +{
> + setup_iomux_uart();
> +
> + return 0;
> +}
> +
> +iomux_v3_cfg_t const ecspi1_pads[] = {
> + MX6_PAD_DISP0_DAT3__ECSPI3_SS0 | MUX_PAD_CTRL(SPI_PAD_CTRL),
> + MX6_PAD_DISP0_DAT4__ECSPI3_SS1 | MUX_PAD_CTRL(SPI_PAD_CTRL),
> + MX6_PAD_DISP0_DAT2__ECSPI3_MISO | MUX_PAD_CTRL(SPI_PAD_CTRL),
> + MX6_PAD_DISP0_DAT1__ECSPI3_MOSI | MUX_PAD_CTRL(SPI_PAD_CTRL),
> + MX6_PAD_DISP0_DAT0__ECSPI3_SCLK | MUX_PAD_CTRL(SPI_PAD_CTRL),
> +};
> +
> +void setup_spi(void)
> +{
> + imx_iomux_v3_setup_multiple_pads(ecspi1_pads,
> + ARRAY_SIZE(ecspi1_pads));
> +}
> +
> +/*
> + * Do not overwrite the console
> + * Use always serial for U-Boot console
> + */
> +int overwrite_console(void)
> +{
> + return 1;
> +}
You do not add video capabilities: you can simply drop overwrite_console().
> +
> +iomux_v3_cfg_t const usdhc3_pads[] = {
> + MX6_PAD_SD3_CLK__USDHC3_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL),
> + MX6_PAD_SD3_CMD__USDHC3_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL),
> + MX6_PAD_SD3_DAT0__USDHC3_DAT0 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
> + MX6_PAD_SD3_DAT1__USDHC3_DAT1 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
> + MX6_PAD_SD3_DAT2__USDHC3_DAT2 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
> + MX6_PAD_SD3_DAT3__USDHC3_DAT3 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
> + MX6_PAD_SD3_DAT4__USDHC3_DAT4 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
> + MX6_PAD_SD3_DAT5__USDHC3_DAT5 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
> + MX6_PAD_SD3_DAT6__USDHC3_DAT6 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
> + MX6_PAD_SD3_DAT7__USDHC3_DAT7 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
> + MX6_PAD_SD3_RST__USDHC3_RST | MUX_PAD_CTRL(USDHC_PAD_CTRL),
> +};
> +
> +int board_mmc_getcd(struct mmc *mmc)
> +{
> + // returns -1 to indicate that no card-detection mechanism is implemented;
> + // 0 indicates that no card is present and
> + // 1 is returned if it was detected that a card is present.
As codestyle we do not use C++ comments
> +int board_eth_init(bd_t *bis)
> +{
> + setup_iomux_enet();
> + fecmxc_initialize(bis);
> +
> + return 0;
> +}
There is not special hndling in this board function. You could move
setup_iomux_enet() into board_early_init() to setup the pinmux and drop
this function. It is then responsability of cpu_eth_init() the
initialization of the FEC controller.
> +
> +#define PC MUX_PAD_CTRL(I2C_PAD_CTRL)
> +
> +/* I2C2 - EDID */
> +struct i2c_pads_info i2c_pad_info1 = {
> + .scl = {
> + .i2c_mode = MX6_PAD_EIM_EB2__I2C2_SCL | PC,
> + .gpio_mode = MX6_PAD_EIM_EB2__GPIO_2_30 | PC,
> + .gp = IMX_GPIO_NR(2, 30)
> + },
> + .sda = {
> + .i2c_mode = MX6_PAD_EIM_D16__I2C2_SDA | PC,
> + .gpio_mode = MX6_PAD_EIM_D16__GPIO_3_16 | PC,
> + .gp = IMX_GPIO_NR(3, 16)
> + }
> +};
> +
> +/* I2C3 - keys, led, temp sensor */
> +struct i2c_pads_info i2c_pad_info2 = {
> + .scl = {
> + .i2c_mode = MX6_PAD_EIM_D17__I2C3_SCL | PC,
> + .gpio_mode = MX6_PAD_EIM_D17__GPIO_3_17 | PC,
> + .gp = IMX_GPIO_NR(3, 17)
> + },
> + .sda = {
> + .i2c_mode = MX6_PAD_EIM_D18__I2C3_SDA | PC,
> + .gpio_mode = MX6_PAD_EIM_D18__GPIO_3_18 | PC,
> + .gp = IMX_GPIO_NR(3, 18)
> + }
> +};
> +
> +iomux_v3_cfg_t const pwm_pad[] = {
> + MX6_PAD_SD1_CMD__PWM4_PWMO | MUX_PAD_CTRL(OUTPUT_40OHM),
> +};
> +
> +static void leds_on(void)
> +{
> + i2c_set_bus_num(2);
> + pca953x_set_dir(0x20, 0xffff, PCA953X_DIR_OUT);
> + pca953x_set_val(0x20, 0xffff, 0x0);
> +}
Please add defines instead of fixed constants.
> +
> +int checkboard(void)
> +{
> + puts("Board: "CONFIG_SYS_BOARD" "CONFIG_BOARDVER" \n");
I see we have some discrepancies in code. Sometimes we use
CONFIG_SYS_BOARD_NAME, sometimes (mx28evk). We have several
CONFIG_SYS_BOARD_*, it will be better to extend the name to
CONFIG_SYS_BOARD_NAME.
Regarding the board version: I understand this is a board type, not a
revision number. Then CONFIG_BOARDVER does not seem the best choice to
represent the meaning.
> diff --git a/include/configs/ot1205.h b/include/configs/ot1205.h
> new file mode 100644
> index 0000000..fc87d7c
> --- /dev/null
> +++ b/include/configs/ot1205.h
> @@ -0,0 +1,231 @@
> +/*
> + * Copyright (C) 2010-2013 Freescale Semiconductor, Inc.
> + * Copyright (C) 2013, Bachmann electronic GmbH
> + *
> + * SPDX-License-Identifier: GPL-2.0+
> + */
> +
> +#ifndef __CONFIG_H
> +#define __CONFIG_H
> +
> +#define CONFIG_MX6
> +#define CONFIG_MX6Q
> +#define CONFIG_DISPLAY_CPUINFO
> +#define CONFIG_DISPLAY_BOARDINFO
> +
> +#include <asm/arch/imx-regs.h>
> +#include <asm/imx-common/gpio.h>
> +
> +#define CONFIG_CMDLINE_TAG
> +#define CONFIG_SETUP_MEMORY_TAGS
> +#define CONFIG_INITRD_TAG
> +#define CONFIG_REVISION_TAG
> +
> +/* Size of malloc() pool */
> +#define CONFIG_SYS_MALLOC_LEN (10 * 1024 * 1024)
> +
> +#define CONFIG_BOARD_EARLY_INIT_F
> +#define CONFIG_MXC_GPIO
> +
> +#define CONFIG_CMD_FUSE
> +#ifdef CONFIG_CMD_FUSE
> +#define CONFIG_MXC_OCOTP
> +#endif
> +
> +/* UART Configs */
> +#define CONFIG_MXC_UART
> +#define CONFIG_MXC_UART_BASE UART1_BASE
> +
> +/* SF Configs */
> +#define CONFIG_CMD_SF
> +#define CONFIG_SPI_FLASH
> +#define CONFIG_SPI_FLASH_STMICRO
> +#define CONFIG_MXC_SPI
> +#define CONFIG_SF_DEFAULT_BUS 2
> +#define CONFIG_SF_DEFAULT_CS (0|(IMX_GPIO_NR(1, 3)<<8))
> +#define CONFIG_SF_DEFAULT_SPEED 25000000
> +#define CONFIG_SF_DEFAULT_MODE (SPI_MODE_0)
> +
> +/* IO expander */
> +#define CONFIG_PCA953X
> +#define CONFIG_SYS_I2C_PCA953X_ADDR 0x20
> +#define CONFIG_SYS_I2C_PCA953X_WIDTH { {0x20, 16} }
> +#define CONFIG_CMD_PCA953X
> +#define CONFIG_CMD_PCA953X_INFO
> +
> +/* I2C Configs */
> +#define CONFIG_CMD_I2C
> +#define CONFIG_SYS_I2C
> +#define CONFIG_SYS_I2C_MXC
> +#define CONFIG_SYS_I2C_SPEED 100000
> +
> +/* OCOTP Configs */
> +#define CONFIG_CMD_IMXOTP
> +#ifdef CONFIG_CMD_IMXOTP
> +#define CONFIG_IMX_OTP
> +#define IMX_OTP_BASE OCOTP_BASE_ADDR
> +#define IMX_OTP_ADDR_MAX 0x7F
> +#define IMX_OTP_DATA_ERROR_VAL 0xBADABADA
> +#define IMX_OTPWRITE_ENABLED
> +#endif
> +
> +/* MMC Configs */
> +#define CONFIG_FSL_ESDHC
> +#define CONFIG_FSL_USDHC
> +#define CONFIG_SYS_FSL_ESDHC_ADDR 0
> +#define CONFIG_SYS_FSL_USDHC_NUM 2
> +
> +#define CONFIG_MMC
> +#define CONFIG_CMD_MMC
> +#define CONFIG_GENERIC_MMC
> +#define CONFIG_BOUNCE_BUFFER
> +
> +#define CONFIG_CMD_PING
> +#define CONFIG_CMD_DHCP
> +#define CONFIG_CMD_MII
> +#define CONFIG_CMD_NET
> +#define CONFIG_FEC_MXC
> +#define CONFIG_MII
> +#define IMX_FEC_BASE ENET_BASE_ADDR
> +#define CONFIG_FEC_XCV_TYPE MII100
> +#define CONFIG_ETHPRIME "FEC"
> +#define CONFIG_FEC_MXC_PHYADDR 0x5
> +#define CONFIG_PHYLIB
> +
> +/* Miscellaneous commands */
> +#define CONFIG_CMD_BMODE
> +#define CONFIG_CMD_SETEXPR
> +
> +/* allow to overwrite serial and ethaddr */
> +#define CONFIG_ENV_OVERWRITE
> +#define CONFIG_CONS_INDEX 1
> +#define CONFIG_BAUDRATE 115200
> +
> +/* Command definition */
> +#include <config_cmd_default.h>
> +
> +#undef CONFIG_CMD_IMLS
> +
> +#define CONFIG_BOOTDELAY 1
> +
> +#define CONFIG_PREBOOT ""
> +
> +#define CONFIG_LOADADDR 0x12000000
> +#define CONFIG_SYS_TEXT_BASE 0x17800000
> +
> +/* Miscellaneous configurable options */
> +#define CONFIG_SYS_LONGHELP
> +#define CONFIG_SYS_HUSH_PARSER
> +#define CONFIG_SYS_PROMPT "U-Boot > "
> +#define CONFIG_SYS_CBSIZE 1024
> +
> +/* Print Buffer Size */
> +#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
> +#define CONFIG_SYS_MAXARGS 16
> +#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
> +
> +#define CONFIG_SYS_LOAD_ADDR CONFIG_LOADADDR
> +
> +#define CONFIG_CMDLINE_EDITING
> +
> +/* Physical Memory Map */
> +#define CONFIG_NR_DRAM_BANKS 1
> +#define PHYS_SDRAM MMDC0_ARB_BASE_ADDR
> +#define PHYS_SDRAM_SIZE (1u * 1024 * 1024 * 1024) /* TODO: needed? */
> +
> +#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM
> +#define CONFIG_SYS_INIT_RAM_ADDR IRAM_BASE_ADDR
> +#define CONFIG_SYS_INIT_RAM_SIZE IRAM_SIZE
> +
> +#define CONFIG_SYS_INIT_SP_OFFSET \
> + (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
> +#define CONFIG_SYS_INIT_SP_ADDR \
> + (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)
> +
> +/* FLASH and environment organization */
> +#define CONFIG_SYS_NO_FLASH
> +
> +#define CONFIG_ENV_SIZE (8 * 1024) /* 8 kb */
> +#define CONFIG_ENV_IS_NOWHERE
> +
> +#define CONFIG_OF_LIBFDT
> +#define CONFIG_CMD_BOOTZ
> +
> +#ifndef CONFIG_SYS_DCACHE_OFF
> +#define CONFIG_CMD_CACHE
> +#endif
> +
> +#define CONFIG_CMD_BOOTZ
> +#define CONFIG_SUPPORT_RAW_INITRD
> +
> +/* FS Configs */
> +#define CONFIG_CMD_EXT3
> +#define CONFIG_CMD_EXT4
> +#define CONFIG_DOS_PARTITION
> +#define CONFIG_CMD_FS_GENERIC
> +
> +/* needed for run-in etc. */
> +#define CONFIG_BOOTP_SERVERIP
> +#define CONFIG_BOOTP_BOOTFILE
> +
> +/*
> + * Memory layout for where various images get loaded by boot scripts
> + */
> +#define MEM_LAYOUT_ENV_SETTINGS \
> + "scriptaddr=0x14000000\0" \
> + "kernel_addr_r=0x10000000\0" \
> + "fdt_addr_r=0x11000000\0" \
> + "ramdisk_addr_r=0x12A00000\0" \
> + "fdt_high=0xffffffff\0" \
> + "initrd_high=0xffffffff\0"
> +
> +#ifdef CONFIG_CMD_MMC
> +#define BOOTCMDS_MMC \
> + "mmc_boot=" \
> + "setenv devtype mmc; " \
> + "if mmc dev ${devnum}; then " \
> + "run scan_boot; " \
> + "fi\0" \
> + "bootcmd_mmc0=setenv devnum 0; run mmc_boot;\0"
> +#define BOOT_TARGETS_MMC "mmc0"
> +#endif
> +
> +#define BOOTCMDS_COMMON \
> + "rootpart=2\0" \
> + \
> + "script_boot=" \
> + "if load ${devtype} ${devnum}:${rootpart} " \
> + "${scriptaddr} ${prefix}${script}; then " \
> + "echo ${script} found! Executing ...;" \
> + "source ${scriptaddr};" \
> + "fi;\0" \
> + \
> + "scan_boot=" \
> + "echo Scanning ${devtype} ${devnum}...; " \
> + "for prefix in ${boot_prefixes}; do " \
> + "for script in ${boot_scripts}; do " \
> + "run script_boot; " \
> + "done; " \
> + "done;\0" \
> + \
> + "boot_targets=" \
> + BOOT_TARGETS_MMC " " \
> + "\0" \
> + \
> + "boot_prefixes=/boot/ \0" \
> + \
> + "boot_scripts=boot.scr\0" \
> + \
> + BOOTCMDS_MMC \
> +
> +#define CONFIG_BOOTCOMMAND \
> + "for target in ${boot_targets}; do run bootcmd_${target}; done"
> +
> +#define CONFIG_EXTRA_ENV_SETTINGS \
> + "soc=imx6d\0" \
> + "board="CONFIG_SYS_BOARD"\0" \
> + "boardver="CONFIG_BOARDVER"\0" \
> + MEM_LAYOUT_ENV_SETTINGS \
> + BOOTCMDS_COMMON
> +
> +#endif /* __CONFIG_H */
>
Best regards,
Stefano Babic
--
=====================================================================
DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sbabic at denx.de
=====================================================================
More information about the U-Boot
mailing list