[U-Boot] [PATCH] powerpc/esdhc: Update esdhc command execution process
Zhang Haijun
b42677 at freescale.com
Fri Nov 8 03:54:38 CET 2013
Abandon this, see [PATCH 7/7 V2] powerpc/esdhc: Update esdhc command
execution process
于 2013/11/8 10:06, Haijun Zhang 写道:
> The max timeout value esdhc host can accept was about 2.69 sec
> At 50 Mhz SD_CLK period, the max busy timeout
> value = 2^27 * SD_CLK period ~= 2.69 sec.
>
> In case erase command CMD38 timeout is caculate by
> mult * 300ms * num(unit by erase group), so the time one erase
> group need should be more than 300ms, 500ms should be enough.
>
> 1. Add data reset for data error and command with busy error.
> 2. Add timeout value detecting during waiting transfer complete.
> 3. Ignore Command inhibit (DAT) state when excuting CMD12.
> 4. Add command CRC error detecting.
> 5. Enlarged the timeout value used for busy state release.
> 6. In case eSDHC host version 2.3, host will signal transfer complete
> interrupt once busy state was release.
>
> Signed-off-by: Haijun Zhang <Haijun.Zhang at freescale.com>
> ---
> drivers/mmc/fsl_esdhc.c | 165 +++++++++++++++++++++++++++++++-----------------
> 1 file changed, 108 insertions(+), 57 deletions(-)
>
> diff --git a/drivers/mmc/fsl_esdhc.c b/drivers/mmc/fsl_esdhc.c
> index 9f4d3a2..10b1fcf 100644
> --- a/drivers/mmc/fsl_esdhc.c
> +++ b/drivers/mmc/fsl_esdhc.c
> @@ -266,26 +266,36 @@ static int
> esdhc_send_cmd(struct mmc *mmc, struct mmc_cmd *cmd, struct mmc_data *data)
> {
> uint xfertyp;
> - uint irqstat;
> + uint irqstat = 0, mask;
> struct fsl_esdhc_cfg *cfg = (struct fsl_esdhc_cfg *)mmc->priv;
> volatile struct fsl_esdhc *regs = (struct fsl_esdhc *)cfg->esdhc_base;
> + int ret = 0, timeout;
> +
> + esdhc_write32(®s->irqstat, -1);
> +
> + sync();
> +
> + mask = PRSSTAT_CICHB | PRSSTAT_CIDHB;
>
> #ifdef CONFIG_SYS_FSL_ERRATUM_ESDHC111
> if (cmd->cmdidx == MMC_CMD_STOP_TRANSMISSION)
> return 0;
> +#else
> + if (cmd->cmdidx == MMC_CMD_STOP_TRANSMISSION)
> + mask &= ~PRSSTAT_CIDHB;
> #endif
>
> - esdhc_write32(®s->irqstat, -1);
> -
> - sync();
> -
> /* Wait for the bus to be idle */
> - while ((esdhc_read32(®s->prsstat) & PRSSTAT_CICHB) ||
> - (esdhc_read32(®s->prsstat) & PRSSTAT_CIDHB))
> - ;
> -
> - while (esdhc_read32(®s->prsstat) & PRSSTAT_DLA)
> - ;
> + timeout = 1000;
> + while (esdhc_read32(®s->prsstat) & mask) {
> + if (timeout == 0) {
> + printf("\nController never released inhibit bit(s).\n");
> + ret = COMM_ERR;
> + goto reset;
> + }
> + timeout--;
> + mdelay(1);
> + }
>
> /* Wait at least 8 SD clock cycles before the next command */
> /*
> @@ -296,11 +306,9 @@ esdhc_send_cmd(struct mmc *mmc, struct mmc_cmd *cmd, struct mmc_data *data)
>
> /* Set up for a data transfer if we have one */
> if (data) {
> - int err;
> -
> - err = esdhc_setup_data(mmc, data);
> - if(err)
> - return err;
> + ret = esdhc_setup_data(mmc, data);
> + if (ret)
> + goto reset;
> }
>
> /* Figure out the transfer arguments */
> @@ -325,43 +333,14 @@ esdhc_send_cmd(struct mmc *mmc, struct mmc_cmd *cmd, struct mmc_data *data)
>
> irqstat = esdhc_read32(®s->irqstat);
>
> - /* Reset CMD and DATA portions on error */
> - if (irqstat & CMD_ERR) {
> - esdhc_write32(®s->sysctl, esdhc_read32(®s->sysctl) |
> - SYSCTL_RSTC);
> - while (esdhc_read32(®s->sysctl) & SYSCTL_RSTC)
> - ;
> -
> - if (data) {
> - esdhc_write32(®s->sysctl,
> - esdhc_read32(®s->sysctl) |
> - SYSCTL_RSTD);
> - while ((esdhc_read32(®s->sysctl) & SYSCTL_RSTD))
> - ;
> - }
> + if (irqstat & IRQSTAT_CTOE) {
> + ret = TIMEOUT;
> + goto reset;
> }
>
> - if (irqstat & IRQSTAT_CTOE)
> - return TIMEOUT;
> -
> - if (irqstat & CMD_ERR)
> - return COMM_ERR;
> -
> - /* Workaround for ESDHC errata ENGcm03648 */
> - if (!data && (cmd->resp_type & MMC_RSP_BUSY)) {
> - int timeout = 2500;
> -
> - /* Poll on DATA0 line for cmd with busy signal for 250 ms */
> - while (timeout > 0 && !(esdhc_read32(®s->prsstat) &
> - PRSSTAT_DAT0)) {
> - udelay(100);
> - timeout--;
> - }
> -
> - if (timeout <= 0) {
> - printf("Timeout waiting for DAT0 to go high!\n");
> - return TIMEOUT;
> - }
> + if (irqstat & CMD_ERR) {
> + ret = COMM_ERR;
> + goto reset;
> }
>
> /* Copy the response to the response buffer */
> @@ -379,28 +358,100 @@ esdhc_send_cmd(struct mmc *mmc, struct mmc_cmd *cmd, struct mmc_data *data)
> } else
> cmd->response[0] = esdhc_read32(®s->cmdrsp0);
>
> - /* Wait until all of the blocks are transferred */
> + /*
> + * At 50 Mhz SD_CLK period, the max busy timeout
> + * value or data transfer time need was about
> + * = 2^27 * SD_CLK period ~= 2.69 sec.
> + * So wait max 10 sec for data transfer complete or busy
> + * state release.
> + */
> + timeout = 10000;
> +
> + /*
> + * eSDHC host V2.3 has response busy interrupt, so
> + * we should wait for busy state to be released and data
> + * was out of programing state before next command send.
> + */
> +#ifdef CONFIG_FSL_SDHC_V2_3
> + if (data || (cmd->resp_type & MMC_RSP_BUSY)) {
> +#else
> if (data) {
> +#endif
> #ifdef CONFIG_SYS_FSL_ESDHC_USE_PIO
> esdhc_pio_read_write(mmc, data);
> #else
> do {
> irqstat = esdhc_read32(®s->irqstat);
>
> - if (irqstat & IRQSTAT_DTOE)
> - return TIMEOUT;
> + if (irqstat & IRQSTAT_DTOE) {
> + ret = TIMEOUT;
> + break;
> + }
>
> - if (irqstat & DATA_ERR)
> - return COMM_ERR;
> - } while ((irqstat & DATA_COMPLETE) != DATA_COMPLETE);
> + if (irqstat & DATA_ERR) {
> + ret = COMM_ERR;
> + break;
> + }
> +
> + if (timeout <= 0) {
> + ret = TIMEOUT;
> + break;
> + }
> + mdelay(1);
> + timeout--;
> + } while (((irqstat & DATA_COMPLETE) != DATA_COMPLETE) &&
> + (esdhc_read32(®s->prsstat) & PRSSTAT_DLA));
> #endif
> if (data->flags & MMC_DATA_READ)
> check_and_invalidate_dcache_range(cmd, data);
> }
>
> + /* Workaround for ESDHC errata ENGcm03648 */
> + if (!data && (cmd->resp_type & MMC_RSP_BUSY)) {
> + int timeout = 5000;
> +
> + /* Poll on DATA0 line for cmd with busy signal for 500 ms */
> + while (timeout > 0 && !(esdhc_read32(®s->prsstat) &
> + PRSSTAT_DAT0)) {
> + udelay(100);
> + timeout--;
> + }
> +
> + if (timeout <= 0) {
> + printf("\nTimeout waiting for DAT0 to go high!\n");
> + ret = TIMEOUT;
> + goto reset;
> + }
> + }
> +
> + if (ret)
> + goto reset;
> +
> esdhc_write32(®s->irqstat, -1);
>
> return 0;
> +
> +reset:
> +
> + /* Reset CMD and DATA portions on error */
> + if (irqstat & (CMD_ERR | DATA_ERR)) {
> + esdhc_write32(®s->sysctl, esdhc_read32(®s->sysctl) |
> + SYSCTL_RSTC);
> + while (esdhc_read32(®s->sysctl) & SYSCTL_RSTC)
> + ;
> +
> + if (data || (cmd->resp_type & MMC_RSP_BUSY)) {
> + esdhc_write32(®s->sysctl,
> + esdhc_read32(®s->sysctl) |
> + SYSCTL_RSTA);
> + while ((esdhc_read32(®s->sysctl) & SYSCTL_RSTA))
> + ;
> + }
> + }
> +
> + esdhc_write32(®s->irqstat, -1);
> +
> + return ret;
> }
>
> static void set_sysctl(struct mmc *mmc, uint clock)
--
Thanks & Regards
Haijun.
More information about the U-Boot
mailing list