[U-Boot] [PATCH 5/5] arm: omap3: Add HEAD acoustics (HA) board variant omap3_ha to tao3530

Stefan Roese sr at denx.de
Tue Nov 12 13:15:03 CET 2013


The Head acoustics (HA) baseboard used the Technexion TAO3530 SOM
and has only some minor differences to the Technexion Thunder baseboard.
This patch adds support for this HA baseboard / TAO3530 as the "omap3_ha"
build target.

Signed-off-by: Stefan Roese <sr at denx.de>
Cc: Tapani Utriainen <tapani at technexion.com>
Cc: Thorsten Eisbein <thorsten.eisbein at head-acoustics.de>
Cc: Tom Rini <trini at ti.com>
---
 board/technexion/tao3530/tao3530.c | 15 +++++++++++++++
 board/technexion/tao3530/tao3530.h |  7 +++++++
 boards.cfg                         |  1 +
 3 files changed, 23 insertions(+)

diff --git a/board/technexion/tao3530/tao3530.c b/board/technexion/tao3530/tao3530.c
index 2f3f929..e829d6f 100644
--- a/board/technexion/tao3530/tao3530.c
+++ b/board/technexion/tao3530/tao3530.c
@@ -75,6 +75,18 @@ out:
  */
 void get_board_mem_timings(struct board_sdrc_timings *timings)
 {
+#if defined(CONFIG_SYS_BOARD_OMAP3_HA)
+	/*
+	 * Switch baseboard LED to red upon power-on
+	 */
+	MUX_OMAP3_HA();
+
+	/* Request a gpio before using it */
+	gpio_request(111, "");
+	/* Sets the gpio as output and its value to 1, switch LED to red */
+	gpio_direction_output(111, 1);
+#endif
+
 	if (tao3530_revision() < 3) {
 		/* 256MB / Bank */
 		timings->mcfg = MCFG(256 << 20, 14);	/* RAS-width 14 */
@@ -162,6 +174,9 @@ int misc_init_r(void)
 void set_muxconf_regs(void)
 {
 	MUX_TAO3530();
+#if defined(CONFIG_SYS_BOARD_OMAP3_HA)
+	MUX_OMAP3_HA();
+#endif
 }
 
 #if defined(CONFIG_GENERIC_MMC) && !defined(CONFIG_SPL_BUILD)
diff --git a/board/technexion/tao3530/tao3530.h b/board/technexion/tao3530/tao3530.h
index 1ea767d..5c0330c 100644
--- a/board/technexion/tao3530/tao3530.h
+++ b/board/technexion/tao3530/tao3530.h
@@ -9,7 +9,11 @@
 
 const omap3_sysinfo sysinfo = {
 	DDR_STACKED,
+#if defined(CONFIG_SYS_BOARD_OMAP3_HA)
+	"HEAD acoustics OMAP3-HA\n",
+#else
 	"OMAP3 TAO-3530 board",
+#endif
 	"NAND",
 };
 
@@ -361,4 +365,7 @@ const omap3_sysinfo sysinfo = {
 	MUX_VAL(CP(SDRC_CKE0),	(IDIS | PTU | EN  | M0)) \
 	MUX_VAL(CP(SDRC_CKE1),	(IDIS | PTU | EN  | M0))
 
+#define MUX_OMAP3_HA() \
+	MUX_VAL(CP(CAM_XCLKB),	(IDIS | PTD | DIS | M4)) /* GPIO_111 */
+
 #endif
diff --git a/boards.cfg b/boards.cfg
index d72be99..90923db 100644
--- a/boards.cfg
+++ b/boards.cfg
@@ -325,6 +325,7 @@ Active  arm         armv7          omap3       logicpd         zoom1
 Active  arm         armv7          omap3       logicpd         zoom2               omap3_zoom2                          -                                                                                                                                 Tom Rix <Tom.Rix at windriver.com>
 Active  arm         armv7          omap3       matrix_vision   mvblx               omap3_mvblx                          -                                                                                                                                 Michael Jones <michael.jones at matrix-vision.de>
 Active  arm         armv7          omap3       nokia           rx51                nokia_rx51                           -                                                                                                                                 Pali Rohár <pali.rohar at gmail.com>
+Active  arm         armv7          omap3       technexion      tao3530             omap3_ha                             tao3530:SYS_BOARD_OMAP3_HA                                                                                                        Stefan Roese <sr at denx.de>
 Active  arm         armv7          omap3       technexion      tao3530             tao3530                              -                                                                                                                                 Tapani Utriainen <linuxfae at technexion.com>
 Active  arm         armv7          omap3       technexion      twister             twister                              -                                                                                                                                 Stefano Babic <sbabic at denx.de>
 Active  arm         armv7          omap3       teejet          mt_ventoux          mt_ventoux                           -                                                                                                                                 Stefano Babic <sbabic at denx.de>
-- 
1.8.4.3



More information about the U-Boot mailing list