[U-Boot] [PATCH] MIPS: use CONFIG_SYS_TEXT_BASE in relocation calculations

[Gabor Juhos]

2013.11.11. 23:36 keltezéssel, Daniel Schwierzeck írta:

<...>

>>> to be consistent with all other architectures, we should keep
>>> CONFIG_SYS_MONITOR_BASE. I think it is neither valid nor intentional
>>> to use a value different from CONFIG_SYS_TEXT_BASE.
>>
>> If it is neither valid nor intentional, the CONFIG_SYS_MONITOR_BASE constant
>> should not exist at all and CONFIG_SYS_TEXT_BASE should be used everywhere
>> instead IMHO.
> 
> By now it is redundant. Once CONFIG_SYS_TEXT_BASE was only a make
> variable named TEXT_BASE and defined in board-specific config.mk. This
>  has been converted with commit
> 14d0a02a168b36e87665b8d7f42fa3e88263d26d.
> 
> BTW the README states:
> 
> - CONFIG_SYS_MONITOR_BASE:
> Physical start address of boot monitor code (set by
> make config files to be same as the text base address
> (CONFIG_SYS_TEXT_BASE) used when linking) - same as
> CONFIG_SYS_FLASH_BASE when booting from flash.

I see. Thank you for the explanation.

>>
>> Additionally, we have this check in arch/mips/lib/board.c:
>>
>>> #if CONFIG_SYS_MONITOR_BASE == CONFIG_SYS_FLASH_BASE
>>>       bd->bi_flashoffset = monitor_flash_len; /* reserved area for U-Boot */
>>> #else
>>>       bd->bi_flashoffset = 0;
>>> #endif
>>
>> If it is not allowed to use different values for the two constants,
>> the condition and the #else branch should be removed.
> 
> no that is still needed if a board has NOR flash but boots from NAND
> or SPI flash or other media (e.g. SoC evaluation boards). In that case
> CONFIG_SYS_TEXT_BASE points usually to an SRAM address.

Ok.

> 
>>
>>> Instead we should change include/configs/malta.h:
>>>
>>> -#define CONFIG_SYS_MONITOR_BASE                CONFIG_SYS_FLASH_BASE
>>> +#define CONFIG_SYS_MONITOR_BASE                CONFIG_SYS_TEXT_BASE
>>>
>>>
>>> Comments?
>>
>> I have tried this already. It is working as well, however with this change the
>> flash sectors containing the bootloader are not protected correctly:
>>
>>> malta # flinfo
>>>
>>> Bank # 1: CFI conformant flash (32 x 32)  Size: 4 MB in 64 Sectors
>>>   Intel Extended command set, Manufacturer ID: 0x00, Device ID: 0x00
>>>   Erase timeout: 16384 ms, write timeout: 3 ms
>>>   Buffer write timeout: 3 ms, buffer size: 2048 bytes
>>>
>>>   Sector Start Addresses:
>>>   BE000000        BE010000        BE020000        BE030000        BE040000
>>>   BE050000        BE060000        BE070000        BE080000        BE090000
>>>   BE0A0000        BE0B0000        BE0C0000        BE0D0000        BE0E0000
>>>   BE0F0000        BE100000        BE110000        BE120000        BE130000
>>>   BE140000        BE150000        BE160000        BE170000        BE180000
>>>   BE190000        BE1A0000        BE1B0000        BE1C0000        BE1D0000
>>>   BE1E0000        BE1F0000        BE200000        BE210000        BE220000
>>>   BE230000        BE240000        BE250000        BE260000        BE270000
>>>   BE280000        BE290000        BE2A0000        BE2B0000        BE2C0000
>>>   BE2D0000        BE2E0000        BE2F0000        BE300000        BE310000
>>>   BE320000        BE330000        BE340000        BE350000        BE360000
>>>   BE370000        BE380000        BE390000        BE3A0000        BE3B0000
>>>   BE3C0000        BE3D0000        BE3E0000   RO   BE3F0000   RO
>>> malta #
>>
>> For reference, this is the output of flinfo with my change:
>>
>>> malta # flinfo
>>>
>>> Bank # 1: CFI conformant flash (32 x 32)  Size: 4 MB in 64 Sectors
>>>   Intel Extended command set, Manufacturer ID: 0x00, Device ID: 0x00
>>>   Erase timeout: 16384 ms, write timeout: 3 ms
>>>   Buffer write timeout: 3 ms, buffer size: 2048 bytes
>>>
>>>   Sector Start Addresses:
>>>   BE000000   RO   BE010000   RO   BE020000   RO   BE030000        BE040000
>>>   BE050000        BE060000        BE070000        BE080000        BE090000
>>>   BE0A0000        BE0B0000        BE0C0000        BE0D0000        BE0E0000
>>>   BE0F0000        BE100000        BE110000        BE120000        BE130000
>>>   BE140000        BE150000        BE160000        BE170000        BE180000
>>>   BE190000        BE1A0000        BE1B0000        BE1C0000        BE1D0000
>>>   BE1E0000        BE1F0000        BE200000        BE210000        BE220000
>>>   BE230000        BE240000        BE250000        BE260000        BE270000
>>>   BE280000        BE290000        BE2A0000        BE2B0000        BE2C0000
>>>   BE2D0000        BE2E0000        BE2F0000        BE300000        BE310000
>>>   BE320000        BE330000        BE340000        BE350000        BE360000
>>>   BE370000        BE380000        BE390000        BE3A0000        BE3B0000
>>>   BE3C0000        BE3D0000        BE3E0000   RO   BE3F0000   RO
>>> malta #
>>
>> Any idea how can we resolve this properly?
>>
>> -Gabor
> 
> following seems to work (in both variants with -bios and -pflash)
> 
> #define CONFIG_SYS_TEXT_BASE 0xbe000000
> #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE

Yeah, this definitely looks better than my solution. :)

Do you want me to incorporate this into the 'malta: use unmapped flash base
address' patch, or do you want to apply this separately?

-Gabor

>