[U-Boot] [PATCH V2 12/14] ARM: AM43xx: EPOS_EVM: Add support for LPDDR2

Lokesh Vutla lokeshvutla at ti.com
Mon Nov 25 06:13:11 CET 2013


On Friday 22 November 2013 02:16 AM, Vaibhav Bedia wrote:
> On Thu, Nov 21, 2013 at 1:18 AM, Lokesh Vutla <lokeshvutla at ti.com> wrote:
>> AM4372 EPOS EVM has 1GB LPDDR2(Part no: MT42L256M32D2LG-25 WT:A)
>> Adding LPDDR2 init sequence and register details for the same.
>> Below is the brief description of LPDDR2 init sequence:
>> -> Configure VTP
>> -> Configure DDR IO settings
>> -> Disable initialization and refreshes until EMIF registers are programmed.
>> -> Program Timing registers
>> -> Program PHY control and Temp alert and ZQ config registers.
>> -> Enable initialization and refreshes and configure SDRAM CONFIG register
>> -> Wait till initialization is complete and the configure MR registers.
>>
> 
> This patch does too many things, some of which affects AM335x and needs to be
> split up. I lost track of what you were doing as i scrolled down :\
It does only two things. Update IO settings and emif configuration.
I wanted to keep these things in a single patch so that if some functionality
breaks down I can burn down to this patch.
> 
>> Signed-off-by: Lokesh Vutla <lokeshvutla at ti.com>
>> ---
>>  arch/arm/cpu/armv7/am33xx/ddr.c                    |  147 +++++++++++++++++++-
>>  arch/arm/cpu/armv7/am33xx/emif4.c                  |   25 +++-
>>  arch/arm/include/asm/arch-am33xx/clocks_am33xx.h   |    3 +
>>  arch/arm/include/asm/arch-am33xx/cpu.h             |    5 +
>>  arch/arm/include/asm/arch-am33xx/ddr_defs.h        |   33 ++++-
>>  arch/arm/include/asm/arch-am33xx/hardware_am43xx.h |    1 +
>>  arch/arm/include/asm/emif.h                        |   12 ++
>>  board/isee/igep0033/board.c                        |   10 +-
>>  board/phytec/pcm051/board.c                        |   12 +-
>>  board/siemens/dxr2/board.c                         |   10 +-
>>  board/siemens/pxm2/board.c                         |   10 +-
>>  board/siemens/rut/board.c                          |   10 +-
>>  board/ti/am335x/board.c                            |   40 +++++-
>>  board/ti/am43xx/board.c                            |   66 +++++++++
>>  board/ti/ti814x/evm.c                              |    4 +-
>>  board/ti/ti816x/evm.c                              |   12 +-
>>  16 files changed, 373 insertions(+), 27 deletions(-)
>>
>> diff --git a/arch/arm/cpu/armv7/am33xx/ddr.c b/arch/arm/cpu/armv7/am33xx/ddr.c
>> index fa697c7..fbee51d 100644
>> --- a/arch/arm/cpu/armv7/am33xx/ddr.c
>> +++ b/arch/arm/cpu/armv7/am33xx/ddr.c
>> @@ -36,6 +36,74 @@ static struct ddr_data_regs *ddr_data_reg[2] = {
>>  static struct ddr_cmdtctrl *ioctrl_reg = {
>>                         (struct ddr_cmdtctrl *)DDR_CONTROL_BASE_ADDR};
>>
>> +static inline u32 get_mr(int nr, u32 cs, u32 mr_addr)
>> +{
>> +       u32 mr;
>> +
>> +       mr_addr |= cs << EMIF_REG_CS_SHIFT;
>> +       writel(mr_addr, &emif_reg[nr]->emif_lpddr2_mode_reg_cfg);
>> +
>> +       mr = readl(&emif_reg[nr]->emif_lpddr2_mode_reg_data);
>> +       debug("get_mr: EMIF1 cs %d mr %08x val 0x%x\n", cs, mr_addr, mr);
>> +       if (((mr & 0x0000ff00) >>  8) == (mr & 0xff) &&
>> +           ((mr & 0x00ff0000) >> 16) == (mr & 0xff) &&
>> +           ((mr & 0xff000000) >> 24) == (mr & 0xff))
>> +               return mr & 0xff;
>> +       else
>> +               return mr;
>> +}
>> +
>> +static inline void set_mr(int nr, u32 cs, u32 mr_addr, u32 mr_val)
>> +{
>> +       mr_addr |= cs << EMIF_REG_CS_SHIFT;
>> +       writel(mr_addr, &emif_reg[nr]->emif_lpddr2_mode_reg_cfg);
>> +       writel(mr_val, &emif_reg[nr]->emif_lpddr2_mode_reg_data);
>> +}
>> +
>> +static void configure_mr(int nr, u32 cs)
>> +{
>> +       u32 mr_addr;
>> +
>> +       while (get_mr(nr, cs, LPDDR2_MR0) & LPDDR2_MR0_DAI_MASK)
>> +               ;
>> +       set_mr(nr, cs, LPDDR2_MR10, 0x56);
>> +
>> +       set_mr(nr, cs, LPDDR2_MR1, 0x43);
>> +       set_mr(nr, cs, LPDDR2_MR2, 0x2);
>> +
>> +       mr_addr = LPDDR2_MR2 | EMIF_REG_REFRESH_EN_MASK;
>> +       set_mr(nr, cs, mr_addr, 0x2);
>> +}
>> +
>> +/*
>> + * Configure EMIF4D5 registers and MR registers
>> + */
>> +void config_sdram_emif4d5(const struct emif_regs *regs, int nr)
>> +{
>> +       writel(0x0, &emif_reg[nr]->emif_pwr_mgmt_ctrl);
>> +       writel(0x0, &emif_reg[nr]->emif_pwr_mgmt_ctrl_shdw);
>> +       writel(0x1, &emif_reg[nr]->emif_iodft_tlgc);
>> +       writel(regs->zq_config, &emif_reg[nr]->emif_zq_config);
>> +
>> +       writel(regs->temp_alert_config, &emif_reg[nr]->emif_temp_alert_config);
>> +       writel(regs->emif_rd_wr_lvl_rmp_win,
>> +              &emif_reg[nr]->emif_rd_wr_lvl_rmp_win);
>> +       writel(regs->emif_rd_wr_lvl_rmp_ctl,
>> +              &emif_reg[nr]->emif_rd_wr_lvl_rmp_ctl);
>> +       writel(regs->emif_rd_wr_lvl_ctl, &emif_reg[nr]->emif_rd_wr_lvl_ctl);
>> +       writel(regs->emif_rd_wr_exec_thresh,
>> +              &emif_reg[nr]->emif_rd_wr_exec_thresh);
>> +
>> +       clrbits_le32(&emif_reg[nr]->emif_sdram_ref_ctrl,
>> +                    EMIF_REG_INITREF_DIS_MASK);
>> +
>> +       writel(regs->sdram_config, &emif_reg[nr]->emif_sdram_config);
>> +       writel(regs->ref_ctrl, &emif_reg[nr]->emif_sdram_ref_ctrl);
>> +
>> +       configure_mr(nr, 0);
>> +       configure_mr(nr, 1);
>> +}
>> +
> 
> Why can't this portion be shared with the other OMAPs? It looks to be
> following a recommended sequence and i can't see why that would vary.
Yes, my ultimate goal is to have a single emif file, but with the current position
of emif file for OMAP's I can't reuse. 
This is in my To do list. I have already discussed this with Tom

Thanks
Lokesh
> 
> It's just too hard to review so many changes in a single patch so i'll stop
> here, sorry.
> 



More information about the U-Boot mailing list