[U-Boot] [PATCH 6/6] T1040QDS: Add support of 2 stage NAND boot loader
Prabhakar Kushwaha
prabhakar at freescale.com
Tue Oct 1 10:28:14 CEST 2013
Add support of 2 stage NAND boot loader using SPL framework.
here, PBL initialise the internal SRAM(256K) and copy SPL(192K). This further
initialise DDR using SPD and environment and copy u-boot(512 kb) from NAND to DDR.
Finally SPL transer control to u-boot.
Initialise/create followings required for SPL framework
- Add spl.c which defines board_init_f, board_init_r
- update tlb and ddr accordingly
Signed-off-by: Prabhakar Kushwaha <prabhakar at freescale.com>
---
Based upon git://git.denx.de/u-boot-mpc85xx.git branch next
board/freescale/t1040qds/Makefile | 9 ++-
board/freescale/t1040qds/README | 33 ++++++++++
board/freescale/t1040qds/ddr.c | 7 ++-
board/freescale/t1040qds/spl.c | 122 +++++++++++++++++++++++++++++++++++++
board/freescale/t1040qds/tlb.c | 8 ++-
boards.cfg | 1 +
include/configs/T1040QDS.h | 58 +++++++++++++++---
7 files changed, 227 insertions(+), 11 deletions(-)
create mode 100644 board/freescale/t1040qds/spl.c
diff --git a/board/freescale/t1040qds/Makefile b/board/freescale/t1040qds/Makefile
index 8f0057b..8f3d7ef 100644
--- a/board/freescale/t1040qds/Makefile
+++ b/board/freescale/t1040qds/Makefile
@@ -8,9 +8,16 @@ include $(TOPDIR)/config.mk
LIB = $(obj)lib$(BOARD).o
+ifdef CONFIG_SPL_BUILD
+COBJS-y += spl.o
+endif
+
+ifndef CONFIG_SPL_BUILD
COBJS-y += $(BOARD).o
+COBJS-$(CONFIG_PCI) += pci.o
+endif
+
COBJS-y += ddr.o
-COBJS-$(CONFIG_PCI) += pci.o
COBJS-y += law.o
COBJS-y += tlb.o
diff --git a/board/freescale/t1040qds/README b/board/freescale/t1040qds/README
index f8b53b4..0e4d32e 100644
--- a/board/freescale/t1040qds/README
+++ b/board/freescale/t1040qds/README
@@ -167,3 +167,36 @@ T1042 Personality
--------------------
T1042 is a reduced personality of T1040 without Integrated 8-port Gigabit
Ethernet switch. Rest of the blocks are same as T1040
+
+
+2 Stage boot loader
+-------------------
+PBL initialise the internal SRAM and copy SPL(192K) in SRAM.
+SPL further initialise DDR using SPD and environment variables and copy
+u-boot(512 KB) from flash to DDR.
+Finally SPL transer control to u-boot for futher booting.
+
+SPL has following features:
+ - Executes within 256K
+ - Actual SPL size 96K + padding till 192K for extra code
+ - No relocation required
+
+ Run time view of SPL framework :-
+ -----------------------------------------------
+ Area | Address |
+ -----------------------------------------------
+ GD, BD | 0x0xFFFC0000 (4K) |
+ -----------------------------------------------
+ HEAP | 0xFFFC1000 (40K) grow downwards |
+ -----------------------------------------------
+ STACK | 0xFFFD0000 (20K) grow upwards |
+ -----------------------------------------------
+ U-boot SPL | 0xfffD0000 - 0xfffffffc (192K) |
+ -----------------------------------------------
+
+Command to build 2 stage NAND boot loader
+ - modify RCW at board/freescale/t1040qds/t1040_rcw.cfg for nand boot
+ -66000002 00000000 fc027000 01000000
+ +66000002 00000000 ec106000 01000000
+ - make T1040QDS_NAND_config
+ - make u-boot-with-spl-pbl.bin
diff --git a/board/freescale/t1040qds/ddr.c b/board/freescale/t1040qds/ddr.c
index 4fd17da..dd2e0cb 100644
--- a/board/freescale/t1040qds/ddr.c
+++ b/board/freescale/t1040qds/ddr.c
@@ -107,11 +107,14 @@ phys_size_t initdram(int board_type)
puts("Initializing....using SPD\n");
+#ifdef CONFIG_SPL_BUILD
dram_size = fsl_ddr_sdram();
dram_size = setup_ddr_tlbs(dram_size / 0x100000);
dram_size *= 0x100000;
-
- puts(" DDR: ");
+#else
+ puts("DDR has been initialised by pre loader\n");
+ dram_size = 0x80000000;
+#endif
return dram_size;
}
diff --git a/board/freescale/t1040qds/spl.c b/board/freescale/t1040qds/spl.c
new file mode 100644
index 0000000..5f39466
--- /dev/null
+++ b/board/freescale/t1040qds/spl.c
@@ -0,0 +1,122 @@
+/*
+ * Copyright 2013 Freescale Semiconductor, Inc.
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <asm/processor.h>
+#include <asm/mmu.h>
+#include <ns16550.h>
+#include <asm/spl.h>
+#include <asm/fsl_law.h>
+#include <asm/fsl_ddr_sdram.h>
+#include <malloc.h>
+#include <nand.h>
+#include <i2c.h>
+#include "../common/qixis.h"
+#include "t1040qds_qixis.h"
+
+DECLARE_GLOBAL_DATA_PTR;
+
+ulong get_effective_memsize(void)
+{
+ return CONFIG_SYS_L3_SIZE;
+}
+
+unsigned long get_board_sys_clk(void)
+{
+ u8 sysclk_conf = QIXIS_READ(brdcfg[1]);
+
+ switch (sysclk_conf & 0x0F) {
+ case QIXIS_SYSCLK_64:
+ return 64000000;
+ case QIXIS_SYSCLK_83:
+ return 83333333;
+ case QIXIS_SYSCLK_100:
+ return 100000000;
+ case QIXIS_SYSCLK_125:
+ return 125000000;
+ case QIXIS_SYSCLK_133:
+ return 133333333;
+ case QIXIS_SYSCLK_150:
+ return 150000000;
+ case QIXIS_SYSCLK_160:
+ return 160000000;
+ case QIXIS_SYSCLK_166:
+ return 166666666;
+ }
+ return 66666666;
+}
+
+unsigned long get_board_ddr_clk(void)
+{
+ u8 ddrclk_conf = QIXIS_READ(brdcfg[1]);
+
+ switch ((ddrclk_conf & 0x30) >> 4) {
+ case QIXIS_DDRCLK_100:
+ return 100000000;
+ case QIXIS_DDRCLK_125:
+ return 125000000;
+ case QIXIS_DDRCLK_133:
+ return 133333333;
+ }
+ return 66666666;
+}
+
+void board_init_f(ulong bootflag)
+{
+ u32 plat_ratio, sys_clk, uart_clk;
+ u32 stack = CONFIG_SPL_RELOC_STACK;
+ ccsr_gur_t *gur = (void *)CONFIG_SYS_MPC85xx_GUTS_ADDR;
+
+ console_init_f();
+
+ /* initialize selected port with appropriate baud rate */
+ sys_clk = get_board_sys_clk();
+ plat_ratio = (in_be32(&gur->rcwsr[0]) >> 25) & 0x1f;
+ uart_clk = sys_clk * plat_ratio / 2;
+
+ NS16550_init((NS16550_t)CONFIG_SYS_NS16550_COM1,
+ uart_clk / 16 / CONFIG_BAUDRATE);
+
+ /* clear BSS segment */
+ memset(__bss_start, 0, __bss_end - __bss_start);
+
+ /* Set STACK pointer */
+ asm volatile ("lwz 1, %0" : : "m"(stack));
+
+ board_init_r(NULL, 0x0);
+}
+
+void board_init_r(gd_t *gd, ulong dest_addr)
+{
+ /* Pointer is writable since we allocated a register for it */
+ gd = (gd_t *)CONFIG_SPL_GD_ADDR;
+ bd_t *bd;
+
+ memset(gd, 0, sizeof(gd_t));
+ bd = (bd_t *)(CONFIG_SPL_GD_ADDR + sizeof(gd_t));
+ memset(bd, 0, sizeof(bd_t));
+ gd->bd = bd;
+ bd->bi_memstart = CONFIG_SYS_INIT_L3_ADDR;
+ bd->bi_memsize = CONFIG_SYS_L3_SIZE;
+
+ probecpu();
+ get_clocks();
+ mem_malloc_init(CONFIG_SPL_RELOC_MALLOC_ADDR,
+ CONFIG_SPL_RELOC_MALLOC_SIZE);
+ env_init();
+
+ /* relocate environment function pointers etc. */
+ env_relocate();
+
+ i2c_init(CONFIG_SYS_FSL_I2C_SPEED, CONFIG_SYS_FSL_I2C_SLAVE);
+
+ gd->ram_size = initdram(0);
+ puts("Second program loader running in sram...\n");
+
+#ifdef CONFIG_SPL_NAND_BOOT
+ nand_boot();
+#endif
+}
diff --git a/board/freescale/t1040qds/tlb.c b/board/freescale/t1040qds/tlb.c
index 412c591..c733040 100644
--- a/board/freescale/t1040qds/tlb.c
+++ b/board/freescale/t1040qds/tlb.c
@@ -52,7 +52,7 @@ struct fsl_e_tlb_entry tlb_table[] = {
SET_TLB_ENTRY(1, CONFIG_SYS_FLASH_BASE, CONFIG_SYS_FLASH_BASE_PHYS,
MAS3_SX|MAS3_SR, MAS2_W|MAS2_G,
0, 2, BOOKE_PAGESZ_256M, 1),
-
+#ifndef CONFIG_SPL_BUILD
/* *I*G* - PCI */
SET_TLB_ENTRY(1, CONFIG_SYS_PCIE1_MEM_VIRT, CONFIG_SYS_PCIE1_MEM_PHYS,
MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
@@ -82,6 +82,7 @@ struct fsl_e_tlb_entry tlb_table[] = {
MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
0, 8, BOOKE_PAGESZ_16M, 1),
#endif
+#endif
#ifdef CONFIG_SYS_DCSRBAR_PHYS
SET_TLB_ENTRY(1, CONFIG_SYS_DCSRBAR, CONFIG_SYS_DCSRBAR_PHYS,
MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
@@ -103,6 +104,11 @@ struct fsl_e_tlb_entry tlb_table[] = {
0, 11, BOOKE_PAGESZ_4K, 1),
#endif
+#if defined(CONFIG_RAMBOOT_PBL) && !defined(CONFIG_SPL_BUILD)
+ SET_TLB_ENTRY(1, CONFIG_SYS_DDR_SDRAM_BASE, CONFIG_SYS_DDR_SDRAM_BASE,
+ MAS3_SX|MAS3_SW|MAS3_SR, 0,
+ 0, 17, BOOKE_PAGESZ_2G, 1)
+#endif
};
int num_tlb_entries = ARRAY_SIZE(tlb_table);
diff --git a/boards.cfg b/boards.cfg
index f103f76..6b04ee2 100644
--- a/boards.cfg
+++ b/boards.cfg
@@ -958,6 +958,7 @@ Active powerpc mpc85xx - freescale t4qds
Active powerpc mpc85xx - freescale t4qds T4240QDS_SPIFLASH T4240QDS:PPC_T4240,RAMBOOT_PBL,SPIFLASH,SYS_TEXT_BASE=0xFFF80000 -
Active powerpc mpc85xx - freescale t4qds T4240QDS_SRIO_PCIE_BOOT T4240QDS:PPC_T4240,SRIO_PCIE_BOOT_SLAVE,SYS_TEXT_BASE=0xFFF80000 -
Active powerpc mpc85xx - freescale t1040qds T1040QDS T1040QDS:PPC_T1040 Naveen Burmi <NaveenBurmi at freescale.com>
+Active powerpc mpc85xx - freescale t1040qds T1040QDS_NAND T1040QDS:PPC_T1040,RAMBOOT_PBL,NAND Poonam Aggrwal <poonam.aggrwal at freescale.com>
Active powerpc mpc85xx - gdsys p1022 controlcenterd_36BIT_SDCARD controlcenterd:36BIT,SDCARD Dirk Eibach <eibach at gdsys.de>
Active powerpc mpc85xx - gdsys p1022 controlcenterd_36BIT_SDCARD_DEVELOP controlcenterd:36BIT,SDCARD,DEVELOP Dirk Eibach <eibach at gdsys.de>
Active powerpc mpc85xx - gdsys p1022 controlcenterd_TRAILBLAZER controlcenterd:TRAILBLAZER,SPIFLASH Dirk Eibach <eibach at gdsys.de>
diff --git a/include/configs/T1040QDS.h b/include/configs/T1040QDS.h
index 7c6bec8..6269ce5 100644
--- a/include/configs/T1040QDS.h
+++ b/include/configs/T1040QDS.h
@@ -30,10 +30,40 @@
#define CONFIG_PHYS_64BIT
#ifdef CONFIG_RAMBOOT_PBL
-#define CONFIG_RAMBOOT_TEXT_BASE CONFIG_SYS_TEXT_BASE
-#define CONFIG_RESET_VECTOR_ADDRESS 0xfffffffc
#define CONFIG_PBLPBI_CONFIG $(SRCTREE)/board/freescale/t1040qds/t1040_pbi.cfg
#define CONFIG_PBLRCW_CONFIG $(SRCTREE)/board/freescale/t1040qds/t1040_rcw.cfg
+#define CONFIG_SPL
+#define CONFIG_SPL_MPC8XXX_INIT_DDR_SUPPORT
+#define CONFIG_SPL_ENV_SUPPORT
+#define CONFIG_SPL_SERIAL_SUPPORT
+#define CONFIG_SPL_FLUSH_IMAGE
+#define CONFIG_SPL_TARGET "u-boot-with-spl.bin"
+#define CONFIG_SPL_LIBGENERIC_SUPPORT
+#define CONFIG_SPL_LIBCOMMON_SUPPORT
+#define CONFIG_SPL_I2C_SUPPORT
+#define CONFIG_FSL_LAW /* Use common FSL init code */
+#define CONFIG_SKIP_RELOCATE_SPL
+#define CONFIG_SYS_TEXT_BASE 0x00201000
+#define CONFIG_SPL_TEXT_BASE 0xFFFD0000
+#define CONFIG_SPL_PAD_TO 0x80000
+#define CONFIG_SPL_MAX_SIZE 0x30000
+#define RESET_VECTOR_OFFSET 0x2FFFC
+#define BOOT_PAGE_OFFSET 0x20000
+#ifdef CONFIG_NAND
+#define CONFIG_SPL_NAND_SUPPORT
+#define CONFIG_SYS_NAND_U_BOOT_SIZE (512 << 10)
+#define CONFIG_SYS_NAND_U_BOOT_DST 0x00200000
+#define CONFIG_SYS_NAND_U_BOOT_START 0x00200000
+#define CONFIG_SYS_NAND_U_BOOT_OFFS (512 << 10)
+#define CONFIG_SYS_LDSCRIPT "arch/powerpc/cpu/mpc85xx/u-boot-nand.lds"
+#define CONFIG_SPL_NAND_BOOT
+#endif
+#ifdef CONFIG_SPL_BUILD
+#define CONFIG_SPL_COMMON_INIT_DDR
+#define CONFIG_SYS_CCSR_DO_NOT_RELOCATE
+#define CONFIG_SYS_NO_FLASH
+#endif
+#define CONFIG_RAMBOOT_TEXT_BASE 0xFFFC0000
#endif
/* High Level Configuration Options */
@@ -97,8 +127,8 @@
#elif defined(CONFIG_NAND)
#define CONFIG_SYS_EXTRA_ENV_RELOC
#define CONFIG_ENV_IS_IN_NAND
-#define CONFIG_ENV_SIZE CONFIG_SYS_NAND_BLOCK_SIZE
-#define CONFIG_ENV_OFFSET (5 * CONFIG_SYS_NAND_BLOCK_SIZE)
+#define CONFIG_ENV_SIZE 0x2000
+#define CONFIG_ENV_OFFSET (8 * CONFIG_SYS_NAND_BLOCK_SIZE)
#else
#define CONFIG_ENV_IS_IN_FLASH
#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - CONFIG_ENV_SECT_SIZE)
@@ -144,7 +174,13 @@ unsigned long get_board_ddr_clk(void);
/*
* Config the L3 Cache as L3 SRAM
*/
-#define CONFIG_SYS_INIT_L3_ADDR 0xFFFC0000
+#define CONFIG_SYS_INIT_L3_ADDR CONFIG_RAMBOOT_TEXT_BASE
+#define CONFIG_SYS_L3_SIZE 256 << 10
+#define CONFIG_SPL_GD_ADDR CONFIG_SYS_INIT_L3_ADDR
+#define CONFIG_SPL_RELOC_MALLOC_ADDR (CONFIG_SYS_INIT_L3_ADDR + 4 * 1024)
+#define CONFIG_SPL_RELOC_MALLOC_SIZE (40 << 10)
+#define CONFIG_SPL_RELOC_STACK (CONFIG_SYS_INIT_L3_ADDR + 64 * 1024)
+#define CONFIG_SPL_RELOC_STACK_SIZE (20 << 10)
#define CONFIG_SYS_DCSRBAR 0xf0000000
#define CONFIG_SYS_DCSRBAR_PHYS 0xf00000000ull
@@ -171,7 +207,9 @@ unsigned long get_board_ddr_clk(void);
#define CONFIG_DDR_SPD
#define CONFIG_FSL_DDR3
+#ifndef CONFIG_SPL_BUILD
#define CONFIG_FSL_DDR_INTERACTIVE
+#endif
#define CONFIG_SYS_SPD_BUS_NUM 0
#define SPD_EEPROM_ADDRESS 0x51
@@ -347,7 +385,11 @@ unsigned long get_board_ddr_clk(void);
#define CONFIG_SYS_CS2_FTIM3 CONFIG_SYS_NAND_FTIM3
#endif
-#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE
+#ifdef CONFIG_SPL_BUILD
+#define CONFIG_SYS_MONITOR_BASE CONFIG_SPL_TEXT_BASE
+#else
+#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE
+#endif
#if defined(CONFIG_RAMBOOT_PBL)
#define CONFIG_SYS_RAMBOOT
@@ -395,7 +437,9 @@ unsigned long get_board_ddr_clk(void);
#define CONFIG_SYS_NS16550_COM3 (CONFIG_SYS_CCSRBAR+0x11D500)
#define CONFIG_SYS_NS16550_COM4 (CONFIG_SYS_CCSRBAR+0x11D600)
#define CONFIG_SERIAL_MULTI /* Enable both serial ports */
+#ifndef CONFIG_SPL_BUILD
#define CONFIG_SYS_CONSOLE_IS_IN_ENV /* determine from environment */
+#endif
/* Use the HUSH parser */
#define CONFIG_SYS_HUSH_PARSER
@@ -589,7 +633,7 @@ unsigned long get_board_ddr_clk(void);
#define CONFIG_SYS_QE_FMAN_FW_ADDR (512 * 1130)
#elif defined(CONFIG_NAND)
#define CONFIG_SYS_QE_FMAN_FW_IN_NAND
-#define CONFIG_SYS_QE_FMAN_FW_ADDR (6 * CONFIG_SYS_NAND_BLOCK_SIZE)
+#define CONFIG_SYS_QE_FMAN_FW_ADDR (9 * CONFIG_SYS_NAND_BLOCK_SIZE)
#else
#define CONFIG_SYS_QE_FMAN_FW_IN_NOR
#define CONFIG_SYS_QE_FMAN_FW_ADDR 0xEFF40000
--
1.7.9.5
More information about the U-Boot
mailing list