[U-Boot] [UBOOT][PATCHv4 4/6] spi: add TI QSPI driver
Jagan Teki
jagannadh.teki at gmail.com
Fri Oct 4 20:57:05 CEST 2013
On Fri, Oct 4, 2013 at 8:21 PM, Sourav Poddar <sourav.poddar at ti.com> wrote:
> From: Matt Porter <matt.porter at linaro.org>
>
> Adds a SPI master driver for the TI QSPI peripheral.
>
> Signed-off-by: Matt Porter <matt.porter at linaro.org>
> Signed-off-by: Sourav Poddar <sourav.poddar at ti.com>
> [Added quad read support and memory mapped support).
What is this comment, any specific?
> ---
You missed change log for all patches, i think you have summarized in 0/6.
I feel it's better write it on individual patches.
> drivers/spi/Makefile | 1 +
> drivers/spi/ti_qspi.c | 328 +++++++++++++++++++++++++++++++++++++++++++++++++
> 2 files changed, 329 insertions(+), 0 deletions(-)
> create mode 100644 drivers/spi/ti_qspi.c
>
> diff --git a/drivers/spi/Makefile b/drivers/spi/Makefile
> index 91d24ce..e5941b0 100644
> --- a/drivers/spi/Makefile
> +++ b/drivers/spi/Makefile
> @@ -38,6 +38,7 @@ COBJS-$(CONFIG_FDT_SPI) += fdt_spi.o
> COBJS-$(CONFIG_TEGRA20_SFLASH) += tegra20_sflash.o
> COBJS-$(CONFIG_TEGRA20_SLINK) += tegra20_slink.o
> COBJS-$(CONFIG_TEGRA114_SPI) += tegra114_spi.o
> +COBJS-$(CONFIG_TI_QSPI) += ti_qspi.o
> COBJS-$(CONFIG_XILINX_SPI) += xilinx_spi.o
> COBJS-$(CONFIG_ZYNQ_SPI) += zynq_spi.o
>
> diff --git a/drivers/spi/ti_qspi.c b/drivers/spi/ti_qspi.c
> new file mode 100644
> index 0000000..d8a03a8
> --- /dev/null
> +++ b/drivers/spi/ti_qspi.c
> @@ -0,0 +1,328 @@
> +/*
> + * TI QSPI driver
> + *
> + * Copyright (C) 2013, Texas Instruments, Incorporated
> + *
> + * SPDX-License-Identifier: GPL-2.0+
Got below format after apply this patch - please check
*Â SPDX-License-Identifier:Â Â Â Â Â GPL-2.0+
> + */
> +
> +#include <common.h>
> +#include <asm/io.h>
> +#include <asm/arch/omap.h>
> +#include <malloc.h>
> +#include <spi.h>
> +
> +struct qspi_regs {
> +u32 pid;
> +u32 pad0[3];
> +u32 sysconfig;
> +u32 pad1[3];
> +u32 intr_status_raw_set;
> +u32 intr_status_enabled_clear;
> +u32 intr_enable_set;
> +u32 intr_enable_clear;
> +u32 intc_eoi;
> +u32 pad2[3];
> +u32 spi_clock_cntrl;
> +u32 spi_dc;
> +u32 spi_cmd;
> +u32 spi_status;
> +u32 spi_data;
> +u32 spi_setup0;
> +u32 spi_setup1;
> +u32 spi_setup2;
> +u32 spi_setup3;
> +u32 spi_switch;
> +u32 spi_data1;
> +u32 spi_data2;
> +u32 spi_data3;
Please add tab space.
> +};
> +
> +struct qspi_slave {
> + struct spi_slave slave;
> + struct qspi_regs *base;
> + unsigned int mode;
> + u32 cmd;
> + u32 dc;
> +};
> +
-- TAG+
> +#define QSPI_TIMEOUT 2000000
> +
> +#define QSPI_FCLK 192000000
> +
> +/* Clock Control */
> +#define QSPI_CLK_EN (1 << 31)
> +#define QSPI_CLK_DIV_MAX 0xffff
> +
> +/* Command */
> +#define QSPI_EN_CS(n) (n << 28)
> +#define QSPI_WLEN(n) ((n-1) << 19)
> +#define QSPI_3_PIN (1 << 18)
> +#define QSPI_RD_SNGL (1 << 16)
> +#define QSPI_WR_SNGL (2 << 16)
> +#define QSPI_INVAL (4 << 16)
> +#define QSPI_RD_QUAD (7 << 16)
> +
> +/* Device Control */
> +#define QSPI_DD(m, n) (m << (3 + n*8))
> +#define QSPI_CKPHA(n) (1 << (2 + n*8))
> +#define QSPI_CSPOL(n) (1 << (1 + n*8))
> +#define QSPI_CKPOL(n) (1 << (n*8))
> +
> +/* Status */
> +#define QSPI_WC (1 << 1)
> +#define QSPI_BUSY (1 << 0)
> +#define QSPI_WC_BUSY (QSPI_WC | QSPI_BUSY)
> +#define QSPI_XFER_DONE QSPI_WC
> +
> +#define MM_SWITCH 0x01
> +#define MEM_CS 0x100
> +#define MEM_CS_UNSELECT 0xfffff0ff
> +#define MMAP_START_ADDR 0x5c000000
> +#define CORE_CTRL_IO 0x4a002558
> +
> +#define QSPI_CMD_READ (0x3 << 0)
> +#define QSPI_CMD_READ_QUAD (0x6b << 0)
> +#define QSPI_CMD_READ_FAST (0x0b << 0)
> +#define QSPI_SETUP0_NUM_A_BYTES (0x2 << 8)
> +#define QSPI_SETUP0_NUM_D_BYTES_NO_BITS (0x0 << 10)
> +#define QSPI_SETUP0_NUM_D_BYTES_8_BITS (0x1 << 10)
> +#define QSPI_SETUP0_READ_NORMAL (0x0 << 12)
> +#define QSPI_SETUP0_READ_QUAD (0x3 << 12)
> +#define QSPI_CMD_WRITE (0x2 << 16)
> +#define QSPI_NUM_DUMMY_BITS (0x0 << 24)
--TAG-
TAG+ ... TAG- please move these macro definitions in below headers
> +
> +static inline struct qspi_slave *to_qspi_slave(struct spi_slave *slave)
> +{
> + return container_of(slave, struct qspi_slave, slave);
> +}
> +static inline struct qspi_regs *get_qspi_bus(int dev)
> +{
> + if (!dev)
> + return (struct qspi_regs *)QSPI_BASE;
> + else
> + return NULL;
> +}
Is this function really required, how many bus controller you have?
> +
> +int spi_cs_is_valid(unsigned int bus, unsigned int cs)
> +{
> + return 1;
> +}
> +
> +void spi_cs_activate(struct spi_slave *slave)
> +{
> + /* CS handled in xfer */
> + return;
> +}
> +
> +void spi_cs_deactivate(struct spi_slave *slave)
> +{
> + /* CS handled in xfer */
> + return;
> +}
> +
> +void spi_init(void)
> +{
> + /* nothing to do */
> +}
> +
> +void spi_set_up_spi_register(struct qspi_slave *qslave)
> +{
> + u32 memval = 0;
> + struct spi_slave *slave = &qslave->slave;
> +
> + slave->memory_map = (void *)MMAP_START_ADDR;
> +
> + memval |= (QSPI_CMD_READ | QSPI_SETUP0_NUM_A_BYTES |
> + QSPI_SETUP0_NUM_D_BYTES_NO_BITS | QSPI_SETUP0_READ_NORMAL |
> + QSPI_CMD_WRITE | QSPI_NUM_DUMMY_BITS);
> +
> + writel(memval, &qslave->base->spi_setup0);
> +}
> +
> +void spi_set_speed(struct spi_slave *slave, uint hz)
> +{
> + struct qspi_slave *qslave = to_qspi_slave(slave);
> +
> + uint clk_div;
> +
> + if (!hz)
> + clk_div = 0;
> + else
> + clk_div = (QSPI_FCLK / hz) - 1;
> +
> + debug("%s: hz: %d, clock divider %d\n", __func__, hz, clk_div);
> +
> + /* disable SCLK */
> + writel(readl(&qslave->base->spi_clock_cntrl) & ~QSPI_CLK_EN,
> + &qslave->base->spi_clock_cntrl);
> +
> + if (clk_div < 0) {
> + debug("%s: clock divider < 0, using /1 divider\n", __func__);
> + clk_div = 0;
> + }
> +
> + if (clk_div > QSPI_CLK_DIV_MAX) {
> + debug("%s: clock divider >%d , using /%d divider\n",
> + __func__, QSPI_CLK_DIV_MAX, QSPI_CLK_DIV_MAX + 1);
> + clk_div = QSPI_CLK_DIV_MAX;
> + }
> +
> + /* enable SCLK */
> + writel(QSPI_CLK_EN | clk_div, &qslave->base->spi_clock_cntrl);
> + debug("%s: spi_clock_cntrl %08x\n", __func__,
> + readl(&qslave->base->spi_clock_cntrl));
> +}
> +
> +struct spi_slave *spi_setup_slave(unsigned int bus, unsigned int cs,
> + unsigned int max_hz, unsigned int mode)
> +{
> + struct qspi_slave *qslave;
> +
> + qslave = spi_alloc_slave(struct qspi_slave, bus, cs);
> + if (!qslave)
> + return NULL;
> +
> + qslave->base = get_qspi_bus(bus);
> + if (qslave->base)
> + debug("No Qspi device found\n");
> + spi_set_speed(&qslave->slave, max_hz);
> + qslave->mode = mode;
> +
> +#ifdef CONFIG_MMAP
> + spi_set_up_spi_register(qslave);
> +#endif
> +
> + debug("%s: bus:%i cs:%i mode:%i\n", __func__, bus, cs, mode);
> +
> + return &qslave->slave;
> +}
> +
> +void spi_free_slave(struct spi_slave *slave)
> +{
> + struct qspi_slave *qslave = to_qspi_slave(slave);
> + free(qslave);
> +}
> +
> +int spi_claim_bus(struct spi_slave *slave)
> +{
> + struct qspi_slave *qslave = to_qspi_slave(slave);
> +
> + debug("%s: bus:%i cs:%i\n", __func__, slave->bus, slave->cs);
> +
> + writel(0, &qslave->base->spi_dc);
> + writel(0, &qslave->base->spi_cmd);
> + writel(0, &qslave->base->spi_data);
> +
> + return 0;
> +}
> +
> +void spi_release_bus(struct spi_slave *slave)
> +{
> + struct qspi_slave *qslave = to_qspi_slave(slave);
> +
> + debug("%s: bus:%i cs:%i\n", __func__, slave->bus, slave->cs);
> +
> + writel(0, &qslave->base->spi_dc);
> + writel(0, &qslave->base->spi_cmd);
> + writel(0, &qslave->base->spi_data);
> +}
> +
> +int spi_xfer(struct spi_slave *slave, unsigned int bitlen, const void *dout,
> + void *din, unsigned long flags)
> +{
> + struct qspi_slave *qslave = to_qspi_slave(slave);
> + uint words = bitlen >> 3; /* fixed 8-bit word length */
> + const uchar *txp = dout;
> + uchar *rxp = din;
> + uint status;
> + int timeout, val;
> +
> + debug("%s: bus:%i cs:%i bitlen:%i words:%i flags:%lx\n", __func__,
> + slave->bus, slave->cs, bitlen, words, flags);
> +
> + qslave->dc = 0;
> + if (qslave->mode & SPI_CPHA)
> + qslave->dc |= QSPI_CKPHA(slave->cs);
> + if (qslave->mode & SPI_CPOL)
> + qslave->dc |= QSPI_CKPOL(slave->cs);
> + if (qslave->mode & SPI_CS_HIGH)
> + qslave->dc |= QSPI_CSPOL(slave->cs);
> +
> + writel(qslave->dc, &qslave->base->spi_dc);
Adjust this code in spi_claim_bus()
> +
> + if (flags & SPI_XFER_MEM_MAP) {
> + writel(MM_SWITCH, &qslave->base->spi_switch);
> + val = readl(CORE_CTRL_IO);
> + val |= MEM_CS;
> + writel(val, CORE_CTRL_IO);
> + return 0;
> + } else if (flags & SPI_XFER_MEM_MAP_END) {
> + writel(~MM_SWITCH, &qslave->base->spi_switch);
> + val = readl(CORE_CTRL_IO);
> + val &= MEM_CS_UNSELECT;
> + writel(val, CORE_CTRL_IO);
> + return 0;
> + }
What is this your are returning from here directly for memory_map? is it?
> +
--TAG+
> + if (bitlen == 0)
> + goto out;
> +
> + if (bitlen % 8) {
> + flags |= SPI_XFER_END;
> + goto out;
> + }
--TAG-
TAG+ .. TAG- please move this code on start of the xfer..ie below debug();
> +
> + /* setup command reg */
> + qslave->cmd = 0;
> + qslave->cmd |= QSPI_WLEN(8);
> + qslave->cmd |= QSPI_EN_CS(slave->cs);
> + if (flags & SPI_3WIRE)
> + qslave->cmd |= QSPI_3_PIN;
> + qslave->cmd |= 0xfff;
> +
> + while (words--) {
> + if (txp) {
> + debug("tx cmd %08x dc %08x data %02x\n",
> + qslave->cmd | QSPI_WR_SNGL, qslave->dc, *txp);
> + writel(*txp++, &qslave->base->spi_data);
> + writel(qslave->cmd | QSPI_WR_SNGL,
> + &qslave->base->spi_cmd);
> + status = readl(&qslave->base->spi_status);
> + timeout = QSPI_TIMEOUT;
> + while ((status & QSPI_WC_BUSY) != QSPI_XFER_DONE) {
> + if (--timeout < 0) {
> + printf("QSPI tx timed out\n");
> + return -1;
> + }
> + status = readl(&qslave->base->spi_status);
> + }
> + debug("tx done, status %08x\n", status);
> + }
> + if (rxp) {
> + qslave->cmd |= QSPI_RD_SNGL;
> + debug("rx cmd %08x dc %08x\n",
> + qslave->cmd, qslave->dc);
> + writel(qslave->cmd, &qslave->base->spi_cmd);
> + status = readl(&qslave->base->spi_status);
> + timeout = QSPI_TIMEOUT;
> + while ((status & QSPI_WC_BUSY) != QSPI_XFER_DONE) {
> + if (--timeout < 0) {
> + printf("QSPI rx timed out\n");
> + return -1;
> + }
> + status = readl(&qslave->base->spi_status);
> + }
> + *rxp++ = readl(&qslave->base->spi_data);
> + debug("rx done, status %08x, read %02x\n",
> + status, *(rxp-1));
> + }
> + }
> +
> +out:
> + /* Terminate frame */
> + if (flags & SPI_XFER_END)
> + writel(qslave->cmd | QSPI_INVAL, &qslave->base->spi_cmd);
Please palce this code in spi_cs_deactivate()
I request you please follow the code structure in below thread.
I feel better if you use same prints that used in below example driver.
http://patchwork.ozlabs.org/patch/265683/
--
Thanks,
Jagan.
--------
Jagannadha Sutradharudu Teki,
E: jagannadh.teki at gmail.com, P: +91-9676773388
Engineer - System Software Hacker
U-boot - SPI Custodian and Zynq APSOC
Ln: http://www.linkedin.com/in/jaganteki
More information about the U-Boot
mailing list