[U-Boot] [PATCH v4 11/11] mpc85xx: introduce the kmp204x reference design support
Valentin Longchamp
valentin.longchamp at keymile.com
Fri Oct 18 11:47:24 CEST 2013
This patch introduces the support for Keymile's kmp204x reference
design. This design is based on Freescale's P2040/P2041 SoC.
The peripherals used by this design are:
- DDR3 RAM with SPD support
- SPI NOR Flash as boot medium
- NAND Flash
- 2 PCIe busses (hosts 1 and 3)
- 3 FMAN Ethernet devices (FMAN1 DTSEC1/2/5)
- 3 Local Bus windows, with one dedicated to the QRIO reset/power mgmt
FPGA
- 2 HW I2C busses
- last but not least, the mandatory serial port
The board/keymile/kmp204x code is mostly based on Freescale's P2041rdb
support and was changed according to our design (that means essentially
removing what is not present on the designs and a few adaptations).
There is currently only one prototype board that is based on this design
and this patch also introduces it. The board is called kmlion1.
Signed-off-by: Stefan Bigler <stefan.bigler at keymile.com>
Signed-off-by: Valentin Longchamp <valentin.longchamp at keymile.com>
kmp204x: update the ENV #define
The comments had to be refined as well as the total size
Signed-off-by: Valentin Longchamp <valentin.longchamp at keymile.com>
---
Changes in v4:
- rebased on mainline u-boot 2013.10
- fixed the name of the board to kmlion1
- changed the ENV #defines
- raised the ENV_SPI_MAX_HZ to 20 MHz
Changes in v3:
- rebased on mainline u-boot 2013.10-rc2 (+ a few patches)
- use new licensing string
- move BCH #defines before keymile-common.h #include
- remove common RCW printing patch
- remove RCW printing form checkboard() as it is now in mpc85xx/cpu.c
- new I2C #defines for new I2C subsystem
- remove patch km-powerpc: move CONFIG_FLASH_CFI_MTD from km-powerpc.h
since km-powerpc is not included by kmp204x.h
- fix RCW for new IRQ/GPIO usage of kmp204x
- set netdev to eth0 since the new DTS now correctly assigns FM1 at DTSEC
to eth0
Changes in v2:
- Remove patch "5/8 fsl: do not define FSL_SRIO_PCIE_BOOT_MASTER for all
P2041 systems" from the series as it is not needed with current u-boot.
- fix the defines used in kmp204x/law.c for the lbus local address
windows.
- fix the header files to include Freescale's copyrights
- integrate Scott's feedback
board/keymile/kmp204x/Makefile | 48 ++++
board/keymile/kmp204x/ddr.c | 64 +++++
board/keymile/kmp204x/eth.c | 71 ++++++
board/keymile/kmp204x/kmp204x.c | 258 +++++++++++++++++++
board/keymile/kmp204x/kmp204x.h | 15 ++
board/keymile/kmp204x/law.c | 40 +++
board/keymile/kmp204x/pbi.cfg | 35 +++
board/keymile/kmp204x/pci.c | 35 +++
board/keymile/kmp204x/rcw_kmp204x.cfg | 11 +
board/keymile/kmp204x/tlb.c | 110 +++++++++
boards.cfg | 3 +
include/configs/km/kmp204x-common.h | 450 ++++++++++++++++++++++++++++++++++
include/configs/kmp204x.h | 68 +++++
13 files changed, 1208 insertions(+)
create mode 100644 board/keymile/kmp204x/Makefile
create mode 100644 board/keymile/kmp204x/ddr.c
create mode 100644 board/keymile/kmp204x/eth.c
create mode 100644 board/keymile/kmp204x/kmp204x.c
create mode 100644 board/keymile/kmp204x/kmp204x.h
create mode 100644 board/keymile/kmp204x/law.c
create mode 100644 board/keymile/kmp204x/pbi.cfg
create mode 100644 board/keymile/kmp204x/pci.c
create mode 100644 board/keymile/kmp204x/rcw_kmp204x.cfg
create mode 100644 board/keymile/kmp204x/tlb.c
create mode 100644 include/configs/km/kmp204x-common.h
create mode 100644 include/configs/kmp204x.h
diff --git a/board/keymile/kmp204x/Makefile b/board/keymile/kmp204x/Makefile
new file mode 100644
index 0000000..35d17ce
--- /dev/null
+++ b/board/keymile/kmp204x/Makefile
@@ -0,0 +1,48 @@
+#
+# (C) Copyright 2001-2007
+# Wolfgang Denk, DENX Software Engineering, wd at denx.de.
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+include $(TOPDIR)/config.mk
+ifneq ($(OBJTREE),$(SRCTREE))
+$(shell mkdir -p $(obj)../common)
+endif
+
+LIB = $(obj)lib$(BOARD).o
+
+COBJS := $(BOARD).o ddr.o eth.o tlb.o pci.o law.o \
+ ../common/common.o ../common/ivm.o
+
+SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c)
+OBJS := $(addprefix $(obj),$(COBJS))
+SOBJS := $(addprefix $(obj),$(SOBJS))
+
+$(LIB): $(obj).depend $(OBJS)
+ $(call cmd_link_o_target, $(OBJS))
+
+#########################################################################
+
+# defines $(obj).depend target
+include $(SRCTREE)/rules.mk
+
+sinclude $(obj).depend
+
+#########################################################################
diff --git a/board/keymile/kmp204x/ddr.c b/board/keymile/kmp204x/ddr.c
new file mode 100644
index 0000000..5bf2646
--- /dev/null
+++ b/board/keymile/kmp204x/ddr.c
@@ -0,0 +1,64 @@
+/*
+ * (C) Copyright 2013 Keymile AG
+ * Valentin Longchamp <valentin.longchamp at keymile.com>
+ *
+ * Copyright 2009-2011 Freescale Semiconductor, Inc.
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <i2c.h>
+#include <hwconfig.h>
+#include <asm/mmu.h>
+#include <asm/fsl_ddr_sdram.h>
+#include <asm/fsl_ddr_dimm_params.h>
+
+void fsl_ddr_board_options(memctl_options_t *popts,
+ dimm_params_t *pdimm,
+ unsigned int ctrl_num)
+{
+ if (ctrl_num) {
+ printf("Wrong parameter for controller number %d", ctrl_num);
+ return;
+ }
+
+ /* automatic calibration for nb of cycles between read and DQS pre */
+ popts->cpo_override = 0xFF;
+
+ /* 1/2 clk delay between wr command and data strobe */
+ popts->write_data_delay = 4;
+ /* clk lauched 1/2 applied cylcle after address command */
+ popts->clk_adjust = 4;
+ /* 1T timing: command/address held for only 1 cycle */
+ popts->twoT_en = 0;
+
+ /* we have only one module, half str should be OK */
+ popts->half_strength_driver_enable = 1;
+
+ /* wrlvl values overriden as recommended by ddr init func */
+ popts->wrlvl_override = 1;
+ popts->wrlvl_sample = 0xf;
+ popts->wrlvl_start = 0x6;
+
+ /* Enable ZQ calibration */
+ popts->zq_en = 1;
+
+ /* DHC_EN =1, ODT = 75 Ohm */
+ popts->ddr_cdr1 = DDR_CDR1_DHC_EN | DDR_CDR_ODT_75ohm;
+}
+
+phys_size_t initdram(int board_type)
+{
+ phys_size_t dram_size = 0;
+
+ puts("Initializing with SPD\n");
+
+ dram_size = fsl_ddr_sdram();
+
+ dram_size = setup_ddr_tlbs(dram_size / 0x100000);
+ dram_size *= 0x100000;
+
+ debug(" DDR: ");
+ return dram_size;
+}
diff --git a/board/keymile/kmp204x/eth.c b/board/keymile/kmp204x/eth.c
new file mode 100644
index 0000000..a073105
--- /dev/null
+++ b/board/keymile/kmp204x/eth.c
@@ -0,0 +1,71 @@
+/*
+ * (C) Copyright 2013 Keymile AG
+ * Valentin Longchamp <valentin.longchamp at keymile.com>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <netdev.h>
+#include <fm_eth.h>
+#include <fsl_mdio.h>
+#include <phy.h>
+
+int board_eth_init(bd_t *bis)
+{
+ int ret = 0;
+#ifdef CONFIG_FMAN_ENET
+ struct fsl_pq_mdio_info dtsec_mdio_info;
+
+ printf("Initializing Fman\n");
+
+ dtsec_mdio_info.regs =
+ (struct tsec_mii_mng *)CONFIG_SYS_FM1_DTSEC1_MDIO_ADDR;
+ dtsec_mdio_info.name = DEFAULT_FM_MDIO_NAME;
+
+ /* Register the real 1G MDIO bus */
+ fsl_pq_mdio_init(bis, &dtsec_mdio_info);
+
+ /* DTESC1/2 don't have a PHY, they are temporarily disabled
+ * so that u-boot doesn't try to unsuccessfuly enable them */
+ fm_disable_port(FM1_DTSEC1);
+ fm_disable_port(FM1_DTSEC2);
+
+ /*
+ * Program RGMII DTSEC5 (FM1 MAC5) on the EC2 physical itf
+ * This is the debug interface, the only one used in u-boot
+ */
+ fm_info_set_phy_address(FM1_DTSEC5, CONFIG_SYS_FM1_DTSEC5_PHY_ADDR);
+ fm_info_set_mdio(FM1_DTSEC5,
+ miiphy_get_dev_by_name(DEFAULT_FM_MDIO_NAME));
+
+ ret = cpu_eth_init(bis);
+
+ /* reenable DTSEC1/2 for later (kernel) */
+ fm_enable_port(FM1_DTSEC1);
+ fm_enable_port(FM1_DTSEC2);
+#endif
+
+ return ret;
+}
+
+#if defined(CONFIG_PHYLIB) && defined(CONFIG_PHY_MARVELL)
+
+#define mv88E1118_PAGE_REG 22
+
+int board_phy_config(struct phy_device *phydev)
+{
+ if (phydev->addr == CONFIG_SYS_FM1_DTSEC5_PHY_ADDR) {
+ /* driver config is good */
+ if (phydev->drv->config)
+ phydev->drv->config(phydev);
+
+ /* but we still need to fix the LEDs */
+ phy_write(phydev, MDIO_DEVAD_NONE, mv88E1118_PAGE_REG, 0x0003);
+ phy_write(phydev, MDIO_DEVAD_NONE, 0x10, 0x0840);
+ phy_write(phydev, MDIO_DEVAD_NONE, mv88E1118_PAGE_REG, 0x0000);
+ }
+
+ return 0;
+}
+#endif
diff --git a/board/keymile/kmp204x/kmp204x.c b/board/keymile/kmp204x/kmp204x.c
new file mode 100644
index 0000000..f02642a
--- /dev/null
+++ b/board/keymile/kmp204x/kmp204x.c
@@ -0,0 +1,258 @@
+/*
+ * (C) Copyright 2013 Keymile AG
+ * Valentin Longchamp <valentin.longchamp at keymile.com>
+ *
+ * Copyright 2011,2012 Freescale Semiconductor, Inc.
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <command.h>
+#include <netdev.h>
+#include <linux/compiler.h>
+#include <asm/mmu.h>
+#include <asm/processor.h>
+#include <asm/cache.h>
+#include <asm/immap_85xx.h>
+#include <asm/fsl_law.h>
+#include <asm/fsl_serdes.h>
+#include <asm/fsl_portals.h>
+#include <asm/fsl_liodn.h>
+#include <fm_eth.h>
+
+#include "../common/common.h"
+#include "kmp204x.h"
+
+DECLARE_GLOBAL_DATA_PTR;
+
+int checkboard(void)
+{
+ printf("Board: Keymile %s\n", CONFIG_KM_BOARD_NAME);
+
+ return 0;
+}
+
+/* TODO: implement the I2C deblocking function */
+int i2c_make_abort(void)
+{
+ return 1;
+}
+
+#define ZL30158_RST 8
+#define ZL30343_RST 9
+
+int board_early_init_f(void)
+{
+ ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR);
+
+ /* board only uses the DDR_MCK0, so disable the DDR_MCK1/2/3 */
+ setbits_be32(&gur->ddrclkdr, 0x001f000f);
+
+ /* take the Zarlinks out of reset as soon as possible */
+ qrio_prst(ZL30158_RST, false, false);
+ qrio_prst(ZL30343_RST, false, false);
+
+ /* and set their reset to power-up only */
+ qrio_prstcfg(ZL30158_RST, PRSTCFG_POWUP_RST);
+ qrio_prstcfg(ZL30343_RST, PRSTCFG_POWUP_RST);
+
+ return 0;
+}
+
+int board_early_init_r(void)
+{
+ /* Flush d-cache and invalidate i-cache of any FLASH data */
+ flush_dcache();
+ invalidate_icache();
+
+ set_liodns();
+ setup_portals();
+
+ return 0;
+}
+
+unsigned long get_board_sys_clk(unsigned long dummy)
+{
+ return 66666666;
+}
+
+#define WDMASK_OFF 0x16
+
+static void qrio_wdmask(u8 bit, bool wden)
+{
+ u16 wdmask;
+ void __iomem *qrio_base = (void *)CONFIG_SYS_QRIO_BASE;
+
+ wdmask = in_be16(qrio_base + WDMASK_OFF);
+
+ if (wden)
+ wdmask |= (1 << bit);
+ else
+ wdmask &= ~(1 << bit);
+
+ out_be16(qrio_base + WDMASK_OFF, wdmask);
+}
+
+#define PRST_OFF 0x1a
+
+void qrio_prst(u8 bit, bool en, bool wden)
+{
+ u16 prst;
+ void __iomem *qrio_base = (void *)CONFIG_SYS_QRIO_BASE;
+
+ qrio_wdmask(bit, wden);
+
+ prst = in_be16(qrio_base + PRST_OFF);
+
+ if (en)
+ prst &= ~(1 << bit);
+ else
+ prst |= (1 << bit);
+
+ out_be16(qrio_base + PRST_OFF, prst);
+}
+
+#define PRSTCFG_OFF 0x1c
+
+void qrio_prstcfg(u8 bit, u8 mode)
+{
+ u32 prstcfg;
+ u8 i;
+ void __iomem *qrio_base = (void *)CONFIG_SYS_QRIO_BASE;
+
+ prstcfg = in_be32(qrio_base + PRSTCFG_OFF);
+
+ for (i = 0; i < 2; i++) {
+ if (mode & (1<<i))
+ set_bit(2*bit+i, &prstcfg);
+ else
+ clear_bit(2*bit+i, &prstcfg);
+ }
+
+ out_be32(qrio_base + PRSTCFG_OFF, prstcfg);
+}
+
+
+#define BOOTCOUNT_OFF 0x12
+
+void bootcount_store(ulong counter)
+{
+ u8 val;
+ void __iomem *qrio_base = (void *)CONFIG_SYS_QRIO_BASE;
+
+ val = (counter <= 255) ? (u8)counter : 255;
+ out_8(qrio_base + BOOTCOUNT_OFF, val);
+}
+
+ulong bootcount_load(void)
+{
+ u8 val;
+ void __iomem *qrio_base = (void *)CONFIG_SYS_QRIO_BASE;
+ val = in_8(qrio_base + BOOTCOUNT_OFF);
+ return val;
+}
+
+#define NUM_SRDS_BANKS 2
+#define PHY_RST 15
+
+int misc_init_r(void)
+{
+ serdes_corenet_t *regs = (void *)CONFIG_SYS_FSL_CORENET_SERDES_ADDR;
+ u32 expected[NUM_SRDS_BANKS] = {SRDS_PLLCR0_RFCK_SEL_100,
+ SRDS_PLLCR0_RFCK_SEL_125};
+ unsigned int i;
+
+ /* check SERDES reference clocks */
+ for (i = 0; i < NUM_SRDS_BANKS; i++) {
+ u32 actual = in_be32(®s->bank[i].pllcr0);
+ actual &= SRDS_PLLCR0_RFCK_SEL_MASK;
+ if (actual != expected[i]) {
+ printf("Warning: SERDES bank %u expects reference \
+ clock %sMHz, but actual is %sMHz\n", i + 1,
+ serdes_clock_to_string(expected[i]),
+ serdes_clock_to_string(actual));
+ }
+ }
+
+ /* take the mgmt eth phy out of reset */
+ qrio_prst(PHY_RST, false, false);
+
+ return 0;
+}
+
+#if defined(CONFIG_HUSH_INIT_VAR)
+int hush_init_var(void)
+{
+ ivm_read_eeprom();
+ return 0;
+}
+#endif
+
+#if defined(CONFIG_LAST_STAGE_INIT)
+int last_stage_init(void)
+{
+ set_km_env();
+ return 0;
+}
+#endif
+
+#ifdef CONFIG_SYS_DPAA_FMAN
+void fdt_fixup_fman_mac_addresses(void *blob)
+{
+ int node, i, ret;
+ char *tmp, *end;
+ unsigned char mac_addr[6];
+
+ /* get the mac addr from env */
+ tmp = getenv("ethaddr");
+ if (!tmp) {
+ printf("ethaddr env variable not defined\n");
+ return;
+ }
+ for (i = 0; i < 6; i++) {
+ mac_addr[i] = tmp ? simple_strtoul(tmp, &end, 16) : 0;
+ if (tmp)
+ tmp = (*end) ? end+1 : end;
+ }
+
+ /* find the correct fdt ethernet path and correct it */
+ node = fdt_path_offset(blob, "/soc/fman/ethernet at e8000");
+ if (node < 0) {
+ printf("no /soc/fman/ethernet path offset\n");
+ return;
+ }
+ ret = fdt_setprop(blob, node, "local-mac-address", &mac_addr, 6);
+ if (ret) {
+ printf("error setting local-mac-address property\n");
+ return;
+ }
+}
+#endif
+
+void ft_board_setup(void *blob, bd_t *bd)
+{
+ phys_addr_t base;
+ phys_size_t size;
+
+ ft_cpu_setup(blob, bd);
+
+ base = getenv_bootm_low();
+ size = getenv_bootm_size();
+
+ fdt_fixup_memory(blob, (u64)base, (u64)size);
+
+#if defined(CONFIG_HAS_FSL_DR_USB) || defined(CONFIG_HAS_FSL_MPH_USB)
+ fdt_fixup_dr_usb(blob, bd);
+#endif
+
+#ifdef CONFIG_PCI
+ pci_of_setup(blob, bd);
+#endif
+
+ fdt_fixup_liodn(blob);
+#ifdef CONFIG_SYS_DPAA_FMAN
+ fdt_fixup_fman_ethernet(blob);
+ fdt_fixup_fman_mac_addresses(blob);
+#endif
+}
diff --git a/board/keymile/kmp204x/kmp204x.h b/board/keymile/kmp204x/kmp204x.h
new file mode 100644
index 0000000..b6ba672
--- /dev/null
+++ b/board/keymile/kmp204x/kmp204x.h
@@ -0,0 +1,15 @@
+/*
+ * (C) Copyright 2013 Keymile AG
+ * Valentin Longchamp <valentin.longchamp at keymile.com>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#define PRSTCFG_POWUP_UNIT_CORE_RST 0x0
+#define PRSTCFG_POWUP_UNIT_RST 0x1
+#define PRSTCFG_POWUP_RST 0x3
+
+void qrio_prst(u8 bit, bool en, bool wden);
+void qrio_prstcfg(u8 bit, u8 mode);
+
+void pci_of_setup(void *blob, bd_t *bd);
diff --git a/board/keymile/kmp204x/law.c b/board/keymile/kmp204x/law.c
new file mode 100644
index 0000000..75d69e8
--- /dev/null
+++ b/board/keymile/kmp204x/law.c
@@ -0,0 +1,40 @@
+/*
+ * (C) Copyright 2013 Keymile AG
+ * Valentin Longchamp <valentin.longchamp at keymile.com>
+ *
+ * Copyright 2008-2011 Freescale Semiconductor, Inc.
+ *
+ * (C) Copyright 2000
+ * Wolfgang Denk, DENX Software Engineering, wd at denx.de.
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <asm/fsl_law.h>
+#include <asm/mmu.h>
+
+struct law_entry law_table[] = {
+#ifdef CONFIG_SYS_BMAN_MEM_PHYS
+ SET_LAW(CONFIG_SYS_BMAN_MEM_PHYS, LAW_SIZE_2M, LAW_TRGT_IF_BMAN),
+#endif
+#ifdef CONFIG_SYS_QMAN_MEM_PHYS
+ SET_LAW(CONFIG_SYS_QMAN_MEM_PHYS, LAW_SIZE_2M, LAW_TRGT_IF_QMAN),
+#endif
+#ifdef CONFIG_SYS_DCSRBAR_PHYS
+ /* Limit DCSR to 32M to access NPC Trace Buffer */
+ SET_LAW(CONFIG_SYS_DCSRBAR_PHYS, LAW_SIZE_32M, LAW_TRGT_IF_DCSR),
+#endif
+#ifdef CONFIG_SYS_NAND_BASE_PHYS
+ SET_LAW(CONFIG_SYS_NAND_BASE_PHYS, LAW_SIZE_32K, LAW_TRGT_IF_LBC),
+#endif
+ SET_LAW(CONFIG_SYS_QRIO_BASE_PHYS, LAW_SIZE_64K, LAW_TRGT_IF_LBC),
+#ifdef CONFIG_SYS_LBAPP1_BASE_PHYS
+ SET_LAW(CONFIG_SYS_LBAPP1_BASE_PHYS, LAW_SIZE_256M, LAW_TRGT_IF_LBC),
+#endif
+#ifdef CONFIG_SYS_LBAPP2_BASE_PHYS
+ SET_LAW(CONFIG_SYS_LBAPP2_BASE_PHYS, LAW_SIZE_256M, LAW_TRGT_IF_LBC),
+#endif
+};
+
+int num_law_entries = ARRAY_SIZE(law_table);
diff --git a/board/keymile/kmp204x/pbi.cfg b/board/keymile/kmp204x/pbi.cfg
new file mode 100644
index 0000000..f38dcf9
--- /dev/null
+++ b/board/keymile/kmp204x/pbi.cfg
@@ -0,0 +1,35 @@
+#
+# Copyright 2012 Freescale Semiconductor, Inc.
+#
+# SPDX-License-Identifier: GPL-2.0+
+#
+# Refer docs/README.pblimage for more details about how-to configure
+# and create PBL boot image
+#
+
+#PBI commands
+#Initialize CPC1 as 1MB SRAM
+09010000 00200400
+09138000 00000000
+091380c0 00000100
+09010100 00000000
+09010104 fff0000b
+09010f00 08000000
+09010000 80000000
+#Configure LAW for CPC1
+09000d00 00000000
+09000d04 fff00000
+09000d08 81000013
+09000010 00000000
+09000014 ff000000
+09000018 81000000
+#Initialize eSPI controller, default configuration is slow for eSPI to
+#load data, this configuration comes from u-boot eSPI driver.
+09110000 80000403
+09110020 27170008
+09110024 00100008
+09110028 00100008
+0911002c 00100008
+#Flush PBL data
+09138000 00000000
+091380c0 00000000
diff --git a/board/keymile/kmp204x/pci.c b/board/keymile/kmp204x/pci.c
new file mode 100644
index 0000000..ec20c8a
--- /dev/null
+++ b/board/keymile/kmp204x/pci.c
@@ -0,0 +1,35 @@
+/*
+ * (C) Copyright 2013 Keymile AG
+ * Valentin Longchamp <valentin.longchamp at keymile.com>
+ *
+ * Copyright 2007-2011 Freescale Semiconductor, Inc.
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <command.h>
+#include <pci.h>
+#include <asm/fsl_pci.h>
+#include <libfdt.h>
+#include <fdt_support.h>
+#include <asm/fsl_serdes.h>
+
+#include "kmp204x.h"
+
+#define PCIE_SW_RST 14
+#define HOOPER_SW_RST 12
+
+void pci_init_board(void)
+{
+ qrio_prst(PCIE_SW_RST, false, false);
+ qrio_prst(HOOPER_SW_RST, false, false);
+ /* Hooper is not direcly PCIe capable */
+ mdelay(50);
+ fsl_pcie_init_board(0);
+}
+
+void pci_of_setup(void *blob, bd_t *bd)
+{
+ FT_FSL_PCI_SETUP;
+}
diff --git a/board/keymile/kmp204x/rcw_kmp204x.cfg b/board/keymile/kmp204x/rcw_kmp204x.cfg
new file mode 100644
index 0000000..f2b7fe3
--- /dev/null
+++ b/board/keymile/kmp204x/rcw_kmp204x.cfg
@@ -0,0 +1,11 @@
+#
+# Default RCW for kmp204x boards
+#
+
+#PBL preamble and RCW header
+aa55aa55 010e0100
+#64 bytes RCW data
+14600000 00000000 28200000 00000000
+148E70CF CFC02000 58000000 41000000
+00000000 00000000 00000000 F4428002
+00000000 00000000 00000000 00000000
diff --git a/board/keymile/kmp204x/tlb.c b/board/keymile/kmp204x/tlb.c
new file mode 100644
index 0000000..d03ca80
--- /dev/null
+++ b/board/keymile/kmp204x/tlb.c
@@ -0,0 +1,110 @@
+/*
+ * (C) Copyright 2013 Keymile AG
+ * Valentin Longchamp <valentin.longchamp at keymile.com>
+ *
+ * Copyright 2008-2011 Freescale Semiconductor, Inc.
+ *
+ * (C) Copyright 2000
+ * Wolfgang Denk, DENX Software Engineering, wd at denx.de.
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <asm/mmu.h>
+
+struct fsl_e_tlb_entry tlb_table[] = {
+ /* TLB 0 - for temp stack in cache */
+ SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR,
+ CONFIG_SYS_INIT_RAM_ADDR_PHYS,
+ MAS3_SW|MAS3_SR, 0,
+ 0, 0, BOOKE_PAGESZ_4K, 0),
+ SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 4 * 1024,
+ CONFIG_SYS_INIT_RAM_ADDR_PHYS + 4 * 1024,
+ MAS3_SW|MAS3_SR, 0,
+ 0, 0, BOOKE_PAGESZ_4K, 0),
+ SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 8 * 1024,
+ CONFIG_SYS_INIT_RAM_ADDR_PHYS + 8 * 1024,
+ MAS3_SW|MAS3_SR, 0,
+ 0, 0, BOOKE_PAGESZ_4K, 0),
+ SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 12 * 1024,
+ CONFIG_SYS_INIT_RAM_ADDR_PHYS + 12 * 1024,
+ MAS3_SW|MAS3_SR, 0,
+ 0, 0, BOOKE_PAGESZ_4K, 0),
+ /* TLB 1 */
+ /* *I*G - L3SRAM. When L3 is used as 1M SRAM, the address of the
+ * SRAM is at 0xfff00000, it covered the 0xfffff000.
+ */
+ SET_TLB_ENTRY(1, CONFIG_SYS_INIT_L3_ADDR, CONFIG_SYS_INIT_L3_ADDR,
+ MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+ 0, 0, BOOKE_PAGESZ_1M, 1),
+
+ /* *I*G* - CCSRBAR */
+ SET_TLB_ENTRY(1, CONFIG_SYS_CCSRBAR, CONFIG_SYS_CCSRBAR_PHYS,
+ MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+ 0, 1, BOOKE_PAGESZ_16M, 1),
+ /* QRIO */
+ SET_TLB_ENTRY(1, CONFIG_SYS_QRIO_BASE, CONFIG_SYS_QRIO_BASE_PHYS,
+ MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+ 0, 2, BOOKE_PAGESZ_64K, 1),
+ /* *I*G* - PCI1 */
+ SET_TLB_ENTRY(1, CONFIG_SYS_PCIE1_MEM_VIRT, CONFIG_SYS_PCIE1_MEM_PHYS,
+ MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+ 0, 3, BOOKE_PAGESZ_512M, 1),
+ /* *I*G* - PCI3 */
+ SET_TLB_ENTRY(1, CONFIG_SYS_PCIE3_MEM_VIRT, CONFIG_SYS_PCIE3_MEM_PHYS,
+ MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+ 0, 4, BOOKE_PAGESZ_512M, 1),
+ /* *I*G* - PCI1&3 I/O */
+ SET_TLB_ENTRY(1, CONFIG_SYS_PCIE1_IO_VIRT, CONFIG_SYS_PCIE1_IO_PHYS,
+ MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+ 0, 6, BOOKE_PAGESZ_128K, 1),
+#ifdef CONFIG_SYS_LBAPP1_BASE_PHYS
+ /* LBAPP1 */
+ SET_TLB_ENTRY(1, CONFIG_SYS_LBAPP1_BASE, CONFIG_SYS_LBAPP1_BASE_PHYS,
+ MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+ 0, 7, BOOKE_PAGESZ_256M, 1),
+#endif
+#ifdef CONFIG_SYS_LBAPP2_BASE_PHYS
+ /* LBAPP2 */
+ SET_TLB_ENTRY(1, CONFIG_SYS_LBAPP2_BASE, CONFIG_SYS_LBAPP2_BASE_PHYS,
+ MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+ 0, 8, BOOKE_PAGESZ_256M, 1),
+#endif
+ /* Bman/Qman */
+#ifdef CONFIG_SYS_BMAN_MEM_PHYS
+ SET_TLB_ENTRY(1, CONFIG_SYS_BMAN_MEM_BASE, CONFIG_SYS_BMAN_MEM_PHYS,
+ MAS3_SW|MAS3_SR, 0,
+ 0, 9, BOOKE_PAGESZ_1M, 1),
+ SET_TLB_ENTRY(1, CONFIG_SYS_BMAN_MEM_BASE + 0x00100000,
+ CONFIG_SYS_BMAN_MEM_PHYS + 0x00100000,
+ MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+ 0, 10, BOOKE_PAGESZ_1M, 1),
+#endif
+#ifdef CONFIG_SYS_QMAN_MEM_PHYS
+ SET_TLB_ENTRY(1, CONFIG_SYS_QMAN_MEM_BASE, CONFIG_SYS_QMAN_MEM_PHYS,
+ MAS3_SW|MAS3_SR, 0,
+ 0, 11, BOOKE_PAGESZ_1M, 1),
+ SET_TLB_ENTRY(1, CONFIG_SYS_QMAN_MEM_BASE + 0x00100000,
+ CONFIG_SYS_QMAN_MEM_PHYS + 0x00100000,
+ MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+ 0, 12, BOOKE_PAGESZ_1M, 1),
+#endif
+#ifdef CONFIG_SYS_DCSRBAR_PHYS
+ SET_TLB_ENTRY(1, CONFIG_SYS_DCSRBAR, CONFIG_SYS_DCSRBAR_PHYS,
+ MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+ 0, 13, BOOKE_PAGESZ_4M, 1),
+#endif
+#ifdef CONFIG_SYS_NAND_BASE
+ /*
+ * *I*G - NAND
+ * entry 14 and 15 has been used hard coded, they will be disabled
+ * in cpu_init_f, so we use entry 16 for nand.
+ */
+ SET_TLB_ENTRY(1, CONFIG_SYS_NAND_BASE, CONFIG_SYS_NAND_BASE_PHYS,
+ MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+ 0, 16, BOOKE_PAGESZ_32K, 1),
+#endif
+};
+
+int num_tlb_entries = ARRAY_SIZE(tlb_table);
diff --git a/boards.cfg b/boards.cfg
index aa2ee64..cacb318 100644
--- a/boards.cfg
+++ b/boards.cfg
@@ -43,6 +43,7 @@
# Status, Arch, CPU:SPLCPU, SoC, Vendor, Board name, Target, Options, Maintainers
###########################################################################################################
+<<<<<<< HEAD
Active arm arm1136 - armltd integrator integratorcp_cm1136 integratorcp:CM1136 Linus Walleij <linus.walleij at linaro.org>
Active arm arm1136 mx31 - - imx31_phycore - -
Active arm arm1136 mx31 davedenx - qong - Wolfgang Denk <wd at denx.de>
@@ -951,6 +952,7 @@ Active powerpc mpc85xx - gdsys p1022
Active powerpc mpc85xx - gdsys p1022 controlcenterd_36BIT_SDCARD_DEVELOP controlcenterd:36BIT,SDCARD,DEVELOP Dirk Eibach <eibach at gdsys.de>
Active powerpc mpc85xx - gdsys p1022 controlcenterd_TRAILBLAZER controlcenterd:TRAILBLAZER,SPIFLASH Dirk Eibach <eibach at gdsys.de>
Active powerpc mpc85xx - gdsys p1022 controlcenterd_TRAILBLAZER_DEVELOP controlcenterd:TRAILBLAZER,SPIFLASH,DEVELOP Dirk Eibach <eibach at gdsys.de>
+Active powerpc mpc85xx - keymile kmp204x kmlion1 kmp204x:KMLION1 Valentin Longchamp <valentin.longchamp at keymile.com>
Active powerpc mpc85xx - stx stxgp3 stxgp3 - Dan Malek <dan at embeddedalley.com>
Active powerpc mpc85xx - stx stxssa stxssa stxssa Dan Malek <dan at embeddedalley.com>
Active powerpc mpc85xx - stx stxssa stxssa_4M stxssa:STXSSA_4M Dan Malek <dan at embeddedalley.com>
@@ -1206,3 +1208,4 @@ Orphan powerpc mpc8xx - - genietv
Orphan powerpc mpc8xx - - mbx8xx MBX - -
Orphan powerpc mpc8xx - - mbx8xx MBX860T - -
Orphan powerpc mpc8xx - - nx823 NX823 - -
+
diff --git a/include/configs/km/kmp204x-common.h b/include/configs/km/kmp204x-common.h
new file mode 100644
index 0000000..2d5320b
--- /dev/null
+++ b/include/configs/km/kmp204x-common.h
@@ -0,0 +1,450 @@
+/*
+ * (C) Copyright 2013 Keymile AG
+ * Valentin Longchamp <valentin.longchamp at keymile.com>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#ifndef _CONFIG_KMP204X_H
+#define _CONFIG_KMP204X_H
+
+#define CONFIG_PHYS_64BIT
+#define CONFIG_PPC_P2041
+
+#define CONFIG_SYS_TEXT_BASE 0xfff80000
+
+#define CONFIG_KM_DEF_NETDEV "netdev=eth0\0"
+
+#define CONFIG_NAND_ECC_BCH
+
+/* common KM defines */
+#include "keymile-common.h"
+
+#define CONFIG_SYS_RAMBOOT
+#define CONFIG_RAMBOOT_PBL
+#define CONFIG_RAMBOOT_TEXT_BASE CONFIG_SYS_TEXT_BASE
+#define CONFIG_RESET_VECTOR_ADDRESS 0xfffffffc
+#define CONFIG_PBLPBI_CONFIG $(SRCTREE)/board/keymile/kmp204x/pbi.cfg
+#define CONFIG_PBLRCW_CONFIG $(SRCTREE)/board/keymile/kmp204x/rcw_kmp204x.cfg
+
+/* High Level Configuration Options */
+#define CONFIG_BOOKE
+#define CONFIG_E500 /* BOOKE e500 family */
+#define CONFIG_E500MC /* BOOKE e500mc family */
+#define CONFIG_SYS_BOOK3E_HV /* Category E.HV supported */
+#define CONFIG_MPC85xx /* MPC85xx/PQ3 platform */
+#define CONFIG_FSL_CORENET /* Freescale CoreNet platform */
+#define CONFIG_MP /* support multiple processors */
+
+#define CONFIG_SYS_FSL_CPC /* Corenet Platform Cache */
+#define CONFIG_SYS_NUM_CPC CONFIG_NUM_DDR_CONTROLLERS
+#define CONFIG_FSL_ELBC /* Has Enhanced localbus controller */
+#define CONFIG_PCI /* Enable PCI/PCIE */
+#define CONFIG_PCIE1 /* PCIE controler 1 */
+#define CONFIG_PCIE3 /* PCIE controler 3 */
+#define CONFIG_FSL_PCI_INIT /* Use common FSL init code */
+#define CONFIG_SYS_PCI_64BIT /* enable 64-bit PCI resources */
+
+#define CONFIG_SYS_DPAA_RMAN /* RMan */
+
+#define CONFIG_FSL_LAW /* Use common FSL init code */
+
+/* Environment in SPI Flash */
+#define CONFIG_SYS_EXTRA_ENV_RELOC
+#define CONFIG_ENV_IS_IN_SPI_FLASH
+#define CONFIG_ENV_SPI_BUS 0
+#define CONFIG_ENV_SPI_CS 0
+#define CONFIG_ENV_SPI_MAX_HZ 20000000
+#define CONFIG_ENV_SPI_MODE 0
+#define CONFIG_ENV_OFFSET 0x100000 /* 1MB for u-boot */
+#define CONFIG_ENV_SIZE 0x004000 /* 16K env */
+#define CONFIG_ENV_SECT_SIZE 0x010000
+#define CONFIG_ENV_OFFSET_REDUND 0x110000
+#define CONFIG_ENV_TOTAL_SIZE 0x020000
+
+#define CONFIG_SYS_REDUNDAND_ENVIRONMENT
+
+#ifndef __ASSEMBLY__
+unsigned long get_board_sys_clk(unsigned long dummy);
+#endif
+#define CONFIG_SYS_CLK_FREQ get_board_sys_clk(0)
+
+/*
+ * These can be toggled for performance analysis, otherwise use default.
+ */
+#define CONFIG_SYS_CACHE_STASHING
+#define CONFIG_BACKSIDE_L2_CACHE
+#define CONFIG_SYS_INIT_L2CSR0 L2CSR0_L2E
+#define CONFIG_BTB /* toggle branch predition */
+
+#define CONFIG_ENABLE_36BIT_PHYS
+
+#define CONFIG_ADDR_MAP
+#define CONFIG_SYS_NUM_ADDR_MAP 64 /* number of TLB1 entries */
+
+#define CONFIG_POST CONFIG_SYS_POST_MEMORY /* test POST memory test */
+#define CONFIG_SYS_MEMTEST_START 0x00100000 /* memtest works on */
+#define CONFIG_SYS_MEMTEST_END 0x00800000
+#define CONFIG_SYS_ALT_MEMTEST
+#define CONFIG_PANIC_HANG /* do not reset board on panic */
+
+/*
+ * Config the L3 Cache as L3 SRAM
+ */
+#define CONFIG_SYS_INIT_L3_ADDR CONFIG_RAMBOOT_TEXT_BASE
+#define CONFIG_SYS_INIT_L3_ADDR_PHYS (0xf00000000ull | \
+ CONFIG_RAMBOOT_TEXT_BASE)
+#define CONFIG_SYS_L3_SIZE (1024 << 10)
+#define CONFIG_SYS_INIT_L3_END (CONFIG_SYS_INIT_L3_ADDR + CONFIG_SYS_L3_SIZE)
+
+#define CONFIG_SYS_DCSRBAR 0xf0000000
+#define CONFIG_SYS_DCSRBAR_PHYS 0xf00000000ull
+
+/*
+ * DDR Setup
+ */
+#define CONFIG_VERY_BIG_RAM
+#define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000
+#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE
+
+#define CONFIG_DIMM_SLOTS_PER_CTLR 1
+#define CONFIG_CHIP_SELECTS_PER_CTRL (4 * CONFIG_DIMM_SLOTS_PER_CTLR)
+
+#define CONFIG_DDR_SPD
+#define CONFIG_FSL_DDR3
+#define CONFIG_FSL_DDR_INTERACTIVE
+
+#define CONFIG_SYS_SPD_BUS_NUM 0
+#define SPD_EEPROM_ADDRESS 0x54
+#define CONFIG_SYS_SDRAM_SIZE 4096 /* for fixed parameter use */
+
+#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */
+#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2
+
+/******************************************************************************
+ * (PRAM usage)
+ * ... -------------------------------------------------------
+ * ... |ROOTFSSIZE | PNVRAM |PHRAM |RESERVED_PRAM | END_OF_RAM
+ * ... |<------------------- pram -------------------------->|
+ * ... -------------------------------------------------------
+ * @END_OF_RAM:
+ * @CONFIG_KM_RESERVED_PRAM: reserved pram for special purpose
+ * @CONFIG_KM_PHRAM: address for /var
+ * @CONFIG_KM_PNVRAM: address for PNVRAM (for the application)
+ * @CONFIG_KM_ROOTFSSIZE: address for rootfilesystem in RAM
+ */
+
+/* size of rootfs in RAM */
+#define CONFIG_KM_ROOTFSSIZE 0x0
+/* pseudo-non volatile RAM [hex] */
+#define CONFIG_KM_PNVRAM 0x80000
+/* physical RAM MTD size [hex] */
+#define CONFIG_KM_PHRAM 0x100000
+/* resereved pram area at the end of memroy [hex] */
+#define CONFIG_KM_RESERVED_PRAM 0x0
+/* enable protected RAM */
+#define CONFIG_PRAM 0
+
+#define CONFIG_KM_CRAMFS_ADDR 0x2000000
+#define CONFIG_KM_KERNEL_ADDR 0x1000000 /* max kernel size 15.5Mbytes */
+#define CONFIG_KM_FDT_ADDR 0x1F80000 /* max dtb size 0.5Mbytes */
+
+#define CONFIG_BOOTCOUNT_LIMIT
+
+/*
+ * Local Bus Definitions
+ */
+
+/* Set the local bus clock 1/8 of plat clk, 2 clk delay LALE */
+#define CONFIG_SYS_LBC_LCRR (LCRR_CLKDIV_8 | LCRR_EADC_2)
+
+/* Nand Flash */
+#define CONFIG_NAND_FSL_ELBC
+#define CONFIG_SYS_NAND_BASE 0xffa00000
+#define CONFIG_SYS_NAND_BASE_PHYS 0xfffa00000ull
+
+#define CONFIG_SYS_NAND_BASE_LIST {CONFIG_SYS_NAND_BASE}
+#define CONFIG_SYS_MAX_NAND_DEVICE 1
+#define CONFIG_MTD_NAND_VERIFY_WRITE
+#define CONFIG_CMD_NAND
+#define CONFIG_SYS_NAND_BLOCK_SIZE (128 * 1024)
+
+#define CONFIG_BCH
+
+/* NAND flash config */
+#define CONFIG_SYS_NAND_BR_PRELIM (BR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \
+ | BR_PS_8 /* Port Size = 8 bit */ \
+ | BR_MS_FCM /* MSEL = FCM */ \
+ | BR_V) /* valid */
+
+#define CONFIG_SYS_NAND_OR_PRELIM (OR_AM_256KB /* length 256K */ \
+ | OR_FCM_BCTLD /* LBCTL not ass */ \
+ | OR_FCM_SCY_1 /* 1 clk wait cycle */ \
+ | OR_FCM_RST /* 1 clk read setup */ \
+ | OR_FCM_PGS /* Large page size */ \
+ | OR_FCM_CST) /* 0.25 command setup */
+
+#define CONFIG_SYS_BR0_PRELIM CONFIG_SYS_NAND_BR_PRELIM /* NAND Base Address */
+#define CONFIG_SYS_OR0_PRELIM CONFIG_SYS_NAND_OR_PRELIM /* NAND Options */
+
+/* QRIO FPGA */
+#define CONFIG_SYS_QRIO_BASE 0xfb000000
+#define CONFIG_SYS_QRIO_BASE_PHYS 0xffb000000ull
+
+#define CONFIG_SYS_QRIO_BR_PRELIM (BR_PHYS_ADDR(CONFIG_SYS_QRIO_BASE_PHYS) \
+ | BR_PS_8 /* Port Size 8 bits */ \
+ | BR_DECC_OFF /* no error corr */ \
+ | BR_MS_GPCM /* MSEL = GPCM */ \
+ | BR_V) /* valid */
+
+#define CONFIG_SYS_QRIO_OR_PRELIM (OR_AM_64KB /* length 64K */ \
+ | OR_GPCM_BCTLD /* no LCTL assert */ \
+ | OR_GPCM_ACS_DIV4 /* LCS 1/4 clk after */ \
+ | OR_GPCM_SCY_2 /* 2 clk wait cycles */ \
+ | OR_GPCM_TRLX /* relaxed tmgs */ \
+ | OR_GPCM_EAD) /* extra bus clk cycles */
+
+#define CONFIG_SYS_BR1_PRELIM CONFIG_SYS_QRIO_BR_PRELIM /* QRIO Base Address */
+#define CONFIG_SYS_OR1_PRELIM CONFIG_SYS_QRIO_OR_PRELIM /* QRIO Options */
+
+#define CONFIG_BOARD_EARLY_INIT_F
+#define CONFIG_BOARD_EARLY_INIT_R /* call board_early_init_r function */
+#define CONFIG_MISC_INIT_R
+#define CONFIG_LAST_STAGE_INIT
+
+#define CONFIG_HWCONFIG
+
+/* define to use L1 as initial stack */
+#define CONFIG_L1_INIT_RAM
+#define CONFIG_SYS_INIT_RAM_LOCK
+#define CONFIG_SYS_INIT_RAM_ADDR 0xffd00000 /* Initial L1 address */
+#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH 0xf
+#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW CONFIG_SYS_INIT_RAM_ADDR
+/* The assembler doesn't like typecast */
+#define CONFIG_SYS_INIT_RAM_ADDR_PHYS \
+ ((CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH * 1ull << 32) | \
+ CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW)
+#define CONFIG_SYS_INIT_RAM_SIZE 0x00004000
+
+#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - \
+ GENERATED_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
+
+#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE
+#define CONFIG_SYS_MONITOR_LEN (512 * 1024)
+#define CONFIG_SYS_MALLOC_LEN (1024 * 1024)
+
+/* Serial Port - controlled on board with jumper J8
+ * open - index 2
+ * shorted - index 1
+ */
+#define CONFIG_CONS_INDEX 1
+#define CONFIG_SYS_NS16550
+#define CONFIG_SYS_NS16550_SERIAL
+#define CONFIG_SYS_NS16550_REG_SIZE 1
+#define CONFIG_SYS_NS16550_CLK (get_bus_freq(0)/2)
+
+#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x11C500)
+#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x11C600)
+#define CONFIG_SYS_NS16550_COM3 (CONFIG_SYS_CCSRBAR+0x11D500)
+#define CONFIG_SYS_NS16550_COM4 (CONFIG_SYS_CCSRBAR+0x11D600)
+
+#define CONFIG_KM_CONSOLE_TTY "ttyS0"
+
+/* Use the HUSH parser */
+#define CONFIG_SYS_HUSH_PARSER
+
+/* pass open firmware flat tree */
+#define CONFIG_OF_LIBFDT
+#define CONFIG_OF_BOARD_SETUP
+#define CONFIG_OF_STDOUT_VIA_ALIAS
+
+/* new uImage format support */
+#define CONFIG_FIT
+#define CONFIG_FIT_VERBOSE /* enable fit_format_{error,warning}() */
+
+/* I2C */
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_NUM_I2C_BUSES 3
+#define CONFIG_SYS_I2C_MAX_HOPS 1
+#define CONFIG_SYS_I2C_FSL /* Use FSL I2C driver */
+#define CONFIG_I2C_MULTI_BUS
+#define CONFIG_I2C_CMD_TREE
+#define CONFIG_SYS_FSL_I2C_SPEED 400000
+#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F
+#define CONFIG_SYS_FSL_I2C_OFFSET 0x118000
+#define CONFIG_SYS_I2C_BUSES { {0, {I2C_NULL_HOP} }, \
+ {0, {{I2C_MUX_PCA9547, 0x70, 1 } } }, \
+ {0, {{I2C_MUX_PCA9547, 0x70, 2 } } }, \
+ }
+
+#define CONFIG_KM_IVM_BUS 1 /* I2C1 (Mux-Port 1)*/
+
+/*
+ * eSPI - Enhanced SPI
+ */
+#define CONFIG_FSL_ESPI
+#define CONFIG_SPI_FLASH
+#define CONFIG_SPI_FLASH_BAR /* 4 byte-addressing */
+#define CONFIG_SPI_FLASH_STMICRO
+#define CONFIG_CMD_SF
+#define CONFIG_SF_DEFAULT_SPEED 20000000
+#define CONFIG_SF_DEFAULT_MODE 0
+
+/*
+ * General PCI
+ * Memory space is mapped 1-1, but I/O space must start from 0.
+ */
+
+/* controller 1, direct to uli, tgtid 3, Base address 20000 */
+#define CONFIG_SYS_PCIE1_MEM_VIRT 0x80000000
+#define CONFIG_SYS_PCIE1_MEM_BUS 0xe0000000
+#define CONFIG_SYS_PCIE1_MEM_PHYS 0xc00000000ull
+#define CONFIG_SYS_PCIE1_MEM_SIZE 0x20000000 /* 512M */
+#define CONFIG_SYS_PCIE1_IO_VIRT 0xf8000000
+#define CONFIG_SYS_PCIE1_IO_BUS 0x00000000
+#define CONFIG_SYS_PCIE1_IO_PHYS 0xff8000000ull
+#define CONFIG_SYS_PCIE1_IO_SIZE 0x00010000 /* 64k */
+
+/* controller 3, Slot 1, tgtid 1, Base address 202000 */
+#define CONFIG_SYS_PCIE3_MEM_VIRT 0xa0000000
+#define CONFIG_SYS_PCIE3_MEM_BUS 0xe0000000
+#define CONFIG_SYS_PCIE3_MEM_PHYS 0xc20000000ull
+#define CONFIG_SYS_PCIE3_MEM_SIZE 0x20000000 /* 512M */
+#define CONFIG_SYS_PCIE3_IO_VIRT 0xf8010000
+#define CONFIG_SYS_PCIE3_IO_BUS 0x00000000
+#define CONFIG_SYS_PCIE3_IO_PHYS 0xff8010000ull
+#define CONFIG_SYS_PCIE3_IO_SIZE 0x00010000 /* 64k */
+
+/* Qman/Bman */
+#define CONFIG_SYS_DPAA_QBMAN /* Support Q/Bman */
+#define CONFIG_SYS_BMAN_NUM_PORTALS 10
+#define CONFIG_SYS_BMAN_MEM_BASE 0xf4000000
+#define CONFIG_SYS_BMAN_MEM_PHYS 0xff4000000ull
+#define CONFIG_SYS_BMAN_MEM_SIZE 0x00200000
+#define CONFIG_SYS_QMAN_NUM_PORTALS 10
+#define CONFIG_SYS_QMAN_MEM_BASE 0xf4200000
+#define CONFIG_SYS_QMAN_MEM_PHYS 0xff4200000ull
+#define CONFIG_SYS_QMAN_MEM_SIZE 0x00200000
+
+#define CONFIG_SYS_DPAA_FMAN
+#define CONFIG_SYS_DPAA_PME
+/* Default address of microcode for the Linux Fman driver
+ * env is stored at 0x100000, sector size is 0x10000, x2 (redundant)
+ * ucode is stored after env, so we got 0x120000.
+ */
+#define CONFIG_SYS_QE_FW_IN_SPIFLASH
+#define CONFIG_SYS_QE_FMAN_FW_ADDR 0x120000
+#define CONFIG_SYS_QE_FMAN_FW_LENGTH 0x10000
+#define CONFIG_SYS_FDT_PAD (0x3000 + CONFIG_SYS_QE_FMAN_FW_LENGTH)
+
+#define CONFIG_FMAN_ENET
+#define CONFIG_PHYLIB_10G
+#define CONFIG_PHY_MARVELL /* there is a marvell phy */
+
+#define CONFIG_PCI_INDIRECT_BRIDGE
+#define CONFIG_PCI_PNP /* do pci plug-and-play */
+#define CONFIG_E1000
+
+#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
+#define CONFIG_DOS_PARTITION
+
+/* RGMII (FM1 at DTESC5) is used as debug itf, it's the only one configured */
+#define CONFIG_SYS_FM1_DTSEC5_PHY_ADDR 0x11
+#define CONFIG_SYS_TBIPA_VALUE 8
+#define CONFIG_PHYLIB /* recommended PHY management */
+#define CONFIG_ETHPRIME "FM1 at DTSEC5"
+#define CONFIG_PHY_GIGE /* Include GbE speed/duplex detection */
+
+/*
+ * Environment
+ */
+#define CONFIG_LOADS_ECHO /* echo on for serial download */
+#define CONFIG_SYS_LOADS_BAUD_CHANGE /* allow baudrate change */
+
+/*
+ * additionnal command line configuration.
+ */
+#define CONFIG_CMD_PCI
+#define CONFIG_CMD_NET
+
+/* we don't need flash support */
+#define CONFIG_SYS_NO_FLASH
+#undef CONFIG_CMD_IMLS
+#undef CONFIG_CMD_FLASH
+#undef CONFIG_FLASH_CFI_MTD
+#undef CONFIG_JFFS2_CMDLINE
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 64 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define CONFIG_SYS_BOOTMAPSZ (64 << 20) /* Initial Memory for Linux */
+#define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */
+
+#ifdef CONFIG_CMD_KGDB
+#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
+#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
+#endif
+
+#define __USB_PHY_TYPE utmi
+
+/*
+ * Environment Configuration
+ */
+#define CONFIG_ENV_OVERWRITE
+#ifndef CONFIG_KM_DEF_ENV /* if not set by keymile-common.h */
+#define CONFIG_KM_DEF_ENV "km-common=empty\0"
+#endif
+
+#ifndef MTDIDS_DEFAULT
+# define MTDIDS_DEFAULT "nand0=fsl_elbc_nand"
+#endif /* MTDIDS_DEFAULT */
+
+#ifndef MTDPARTS_DEFAULT
+# define MTDPARTS_DEFAULT "mtdparts=" \
+ "fsl_elbc_nand:" \
+ "-(" CONFIG_KM_UBI_PARTITION_NAME_BOOT ");"
+#endif /* MTDPARTS_DEFAULT */
+
+/* architecture specific default bootargs */
+#define CONFIG_KM_DEF_BOOT_ARGS_CPU ""
+
+/* FIXME: FDT_ADDR is unspecified */
+#define CONFIG_KM_DEF_ENV_CPU \
+ "boot=bootm ${load_addr_r} - ${fdt_addr_r}\0" \
+ "cramfsloadfdt=" \
+ "cramfsload ${fdt_addr_r} " \
+ "fdt_0x${IVM_BoardId}_0x${IVM_HWKey}.dtb\0" \
+ "fdt_addr_r=" __stringify(CONFIG_KM_FDT_ADDR) "\0" \
+ "u-boot="__stringify(CONFIG_HOSTNAME) "/u-boot.pbl\0" \
+ "update=" \
+ "sf probe 0;sf erase 0 +${filesize};" \
+ "sf write ${load_addr_r} 0 ${filesize};\0" \
+ ""
+
+#define CONFIG_HW_ENV_SETTINGS \
+ "hwconfig=fsl_ddr:ctlr_intlv=cacheline\0" \
+ "usb_phy_type=" __stringify(__USB_PHY_TYPE) "\0" \
+ "usb_dr_mode=host\0"
+
+#define CONFIG_KM_NEW_ENV \
+ "newenv=sf probe 0;" \
+ "sf erase " __stringify(CONFIG_ENV_OFFSET) " " \
+ __stringify(CONFIG_ENV_TOTAL_SIZE)"\0"
+
+/* ppc_82xx is the equivalent to ppc_6xx, the generic ppc toolchain */
+#ifndef CONFIG_KM_DEF_ARCH
+#define CONFIG_KM_DEF_ARCH "arch=ppc_82xx\0"
+#endif
+
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ CONFIG_KM_DEF_ENV \
+ CONFIG_KM_DEF_ARCH \
+ CONFIG_KM_NEW_ENV \
+ CONFIG_HW_ENV_SETTINGS \
+ "EEprom_ivm=pca9547:70:9\0" \
+ ""
+
+#endif /* _CONFIG_KMP204X_H */
diff --git a/include/configs/kmp204x.h b/include/configs/kmp204x.h
new file mode 100644
index 0000000..4158c8d
--- /dev/null
+++ b/include/configs/kmp204x.h
@@ -0,0 +1,68 @@
+/*
+ * (C) Copyright 2013 Keymile AG
+ * Valentin Longchamp <valentin.longchamp at keymile.com>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+/* KMLION1 */
+#if defined(CONFIG_KMLION1)
+#define CONFIG_HOSTNAME kmlion1
+#define CONFIG_KM_BOARD_NAME "kmlion1"
+
+#else
+#error ("Board not supported")
+#endif
+
+#define CONFIG_KMP204X
+
+#include "km/kmp204x-common.h"
+
+#if defined(CONFIG_KMLION1)
+/* App1 Local bus */
+#define CONFIG_SYS_LBAPP1_BASE 0xD0000000
+#define CONFIG_SYS_LBAPP1_BASE_PHYS 0xFD0000000ull
+
+#define CONFIG_SYS_LBAPP1_BR_PRELIM (BR_PHYS_ADDR(CONFIG_SYS_LBAPP1_BASE_PHYS) \
+ | BR_PS_8 /* Port Size 8 bits */ \
+ | BR_DECC_OFF /* no error corr */ \
+ | BR_MS_GPCM /* MSEL = GPCM */ \
+ | BR_V) /* valid */
+
+#define CONFIG_SYS_LBAPP1_OR_PRELIM (OR_AM_256MB /* length 256MB */ \
+ | OR_GPCM_ACS_DIV2 /* LCS 1/2 clk after */ \
+ | OR_GPCM_CSNT /* LCS 1/4 clk before */ \
+ | OR_GPCM_SCY_2 /* 2 clk wait cycles */ \
+ | OR_GPCM_TRLX /* relaxed tmgs */ \
+ | OR_GPCM_EAD) /* extra bus clk cycles */
+/* Local bus app1 Base Address */
+#define CONFIG_SYS_BR2_PRELIM CONFIG_SYS_LBAPP1_BR_PRELIM
+/* Local bus app1 Options */
+#define CONFIG_SYS_OR2_PRELIM CONFIG_SYS_LBAPP1_OR_PRELIM
+
+/* App2 Local bus */
+#define CONFIG_SYS_LBAPP2_BASE 0xE0000000
+#define CONFIG_SYS_LBAPP2_BASE_PHYS 0xFE0000000ull
+
+#define CONFIG_SYS_LBAPP2_BR_PRELIM (BR_PHYS_ADDR(CONFIG_SYS_LBAPP2_BASE_PHYS) \
+ | BR_PS_8 /* Port Size 8 bits */ \
+ | BR_DECC_OFF /* no error corr */ \
+ | BR_MS_GPCM /* MSEL = GPCM */ \
+ | BR_V) /* valid */
+
+#define CONFIG_SYS_LBAPP2_OR_PRELIM (OR_AM_256MB /* length 256MB */ \
+ | OR_GPCM_ACS_DIV2 /* LCS 1/2 clk after */ \
+ | OR_GPCM_CSNT /* LCS 1/4 clk before */ \
+ | OR_GPCM_SCY_2 /* 2 clk wait cycles */ \
+ | OR_GPCM_TRLX /* relaxed tmgs */ \
+ | OR_GPCM_EAD) /* extra bus clk cycles */
+/* Local bus app2 Base Address */
+#define CONFIG_SYS_BR3_PRELIM CONFIG_SYS_LBAPP2_BR_PRELIM
+/* Local bus app2 Options */
+#define CONFIG_SYS_OR3_PRELIM CONFIG_SYS_LBAPP2_OR_PRELIM
+#endif
+
+#endif /* __CONFIG_H */
--
1.8.0.1
More information about the U-Boot
mailing list