[U-Boot] [PATCH] arm: trats: add the sd-card power control function.

Jaehoon Chung jh80.chung at samsung.com
Thu Oct 31 14:37:45 CET 2013


To use the sd-card, VTF_2.8V will be enabled.
Before this patch, VTF_2.8V is always disabled.(card can't initialize.)
When card is detected, SD-card power will enable with sd_ldo_control().

Signed-off-by: Jaehoon Chung <jh80.chung at samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park at samsung.com>
---
 board/samsung/trats/trats.c |   38 ++++++++++++++++++++++++++++++++------
 1 file changed, 32 insertions(+), 6 deletions(-)

diff --git a/board/samsung/trats/trats.c b/board/samsung/trats/trats.c
index 7f61d17..9b6dd12 100644
--- a/board/samsung/trats/trats.c
+++ b/board/samsung/trats/trats.c
@@ -408,11 +408,31 @@ int checkboard(void)
 #endif
 
 #ifdef CONFIG_GENERIC_MMC
+static int sd_ldo_control(int on)
+{
+	struct pmic *p = pmic_get("MAX8997_PMIC");
+	u32 val = 0;
+	int ret = 0;
+	if (pmic_probe(p))
+		return -1;
+
+	/* LDO17 VTF: 2.8V */
+	val = max8997_reg_ldo(2800000) | (on? EN_LDO : DIS_LDO);
+	ret |= pmic_reg_write(p, MAX8997_REG_LDO17CTRL, val);
+
+	if (ret) {
+		puts("MAX8997 SD setting error!\n");
+		return -1;
+	}
+
+	return 0;
+}
+
 int board_mmc_init(bd_t *bis)
 {
 	struct exynos4_gpio_part2 *gpio =
 		(struct exynos4_gpio_part2 *)samsung_get_base_gpio_part2();
-	int err;
+	int err, err_sd = 0;
 
 	/* eMMC_EN: SD_0_CDn: GPK0[2] Output High */
 	s5p_gpio_direction_output(&gpio->k0, 2, 1);
@@ -438,14 +458,20 @@ int board_mmc_init(bd_t *bis)
 	 * GPX3[4] T-flash detect pin
 	 */
 	if (!s5p_gpio_get_value(&gpio->x3, 4)) {
-		err = exynos_pinmux_config(PERIPH_ID_SDMMC2, PINMUX_FLAG_NONE);
-		if (err)
+		err_sd = exynos_pinmux_config(PERIPH_ID_SDMMC2, PINMUX_FLAG_NONE);
+		if (err_sd)
 			debug("SDMMC2 not configured\n");
-		else
-			err = s5p_mmc_init(2, 4);
+		else {
+			if (!sd_ldo_control(1)) {
+				err_sd = s5p_mmc_init(2, 4);
+				if (err_sd) {
+					sd_ldo_control(0);
+				}
+			}
+		}
 	}
 
-	return err;
+	return err & err_sd;
 }
 #endif
 
-- 
1.7.9.5


More information about the U-Boot mailing list