[U-Boot] P2041RDB fails to boot with master (and 2013.10-rc1)

[sun york-R58495]

Chris,

Thanks a lot to bring this to our attention.

A brief look at the log shows the SPD wasn't found, probably due to recent I2C change. We will address this issue as soon as possible.

York

-------- Original Message --------
From: Chris Packham
Sent: Mon, 09/09/2013 22:26
To: u-boot
CC: sun york-R58495 ; Xie Shaohui-B21989 ; afleming at freescale.com
Subject: P2041RDB fails to boot with master (and 2013.10-rc1)


Hi,

I was just looking at something else and found that my P2041RDB no
longer boots from the master branch of u-boot.git (it hangs after DDR
initialisation). I checked 2013.10-rc1, same problem. 2013.07 works.

I haven't bisected further than that. I just thought I'd fire this off
now since it appears to be a regression that might affect 2013.10.

Thanks,
Chris

--

Output from 2013.10-rc1

U-Boot 2013.10-rc1 (Sep 10 2013 - 17:08:26)

CPU0:  P2041E, Version: 1.0, (0x82180110)
Core:  e500mc, Version: 2.2, (0x80230022)
Clock Configuration:
       CPU0:1500 MHz, CPU1:1500 MHz, CPU2:1500 MHz, CPU3:1500 MHz,
       CCB:750  MHz,
       DDR:666.667 MHz (1333.333 MT/s data rate) (Asynchronous), LBC:93.750 MHz
       FMAN1: 583.333 MHz
       QMAN:  375 MHz
       PME:   375 MHz
L1:    D-cache 32 kB enabled
       I-cache 32 kB enabled
Reset Configuration Word (RCW):
       00000000: 12600000 00000000 241c0000 00000000
       00000010: 249f40c0 c3c02000 fe800000 40000000
       00000020: 00000000 00000000 00000000 d0030f07
       00000030: 00000000 00000000 00000000 00000000
Board: P2041RDB, CPLD version: 3.0 vBank: 0
SERDES Reference Clocks: Bank1=100Mhz Bank2=125Mhz
I2C:   ready
SPI:   ready
DRAM:  Initializing....WARNING: Calling __hwconfig without a buffer
and before environment is ready
using SPD
DDR: failed to read SPD from address 82
WARNING: Calling __hwconfig without a buffer and before environment is ready
WARNING: Calling __hwconfig without a buffer and before environment is ready
16 MiB (DDR2, 64-bit, CL=0.5, ECC off)
Testing 0x00000000 - 0x00ffffff
Remap DDR

Output from 2013.07


U-Boot 2013.07 (Sep 10 2013 - 17:00:18)

CPU0:  P2041E, Version: 1.0, (0x82180110)
Core:  e500mc, Version: 2.2, (0x80230022)
Clock Configuration:
       CPU0:1500 MHz, CPU1:1500 MHz, CPU2:1500 MHz, CPU3:1500 MHz,
       CCB:750  MHz,
       DDR:666.667 MHz (1333.333 MT/s data rate) (Asynchronous), LBC:93.750 MHz
       FMAN1: 583.333 MHz
       QMAN:  375 MHz
       PME:   375 MHz
L1:    D-cache 32 kB enabled
       I-cache 32 kB enabled
Board: P2041RDB, CPLD version: 3.0 vBank: 0
Reset Configuration Word (RCW):
       00000000: 12600000 00000000 241c0000 00000000
       00000010: 249f40c0 c3c02000 fe800000 40000000
       00000020: 00000000 00000000 00000000 d0030f07
       00000030: 00000000 00000000 00000000 00000000
SERDES Reference Clocks: Bank1=100Mhz Bank2=125Mhz
I2C:   ready
SPI:   ready
DRAM:  Initializing....using SPD
Detected UDIMM UG51U6400N8SU-ACF
2 GiB left unmapped
4 GiB (DDR3, 64-bit, CL=9, ECC off)
       DDR Chip-Select Interleaving Mode: CS0+CS1
Testing 0x00000000 - 0x7fffffff
Testing 0x80000000 - 0xffffffff
Remap DDR 2 GiB left unmapped

POST memory PASSED
Flash: 128 MiB
L2:    128 KB enabled
Corenet Platform Cache: 1024 KB enabled
SERDES: bank 3 disabled
SRIO1: disabled
SRIO2: disabled
NAND:  0 MiB
MMC:  FSL_SDHC: 0
EEPROM: Invalid ID (ff ff ff ff)
PCIe1: disabled
PCIe2: Root Complex, no link, regs @ 0xfe201000
PCIe2: Bus 00 - 00
PCIe3: disabled
In:    serial
Out:   serial
Err:   serial
Net:   Initializing Fman
Fman1: DTSEC3 set to unknown interface 12
Fman1: Uploading microcode version 101.8.0
Phy not found
PHY reset timed out
FM1 at DTSEC1, FM1 at DTSEC2, FM1 at DTSEC4, FM1 at DTSEC5, FM1 at TGEC1
=>