[U-Boot] [PATCH] 2c: modify i2c_read API to handle multi-bytes writes

Shaveta Leekha shaveta at freescale.com
Fri Apr 4 12:08:28 CEST 2014


Most of the I2C slaves support accesses in the typical style
viz.read/write series of bytes at particular address offset.
These transactions are currently supportd in the
i2c driver using i2c_read and i2c_write APIs. I2C EEPROMs,
RTC, etc fall in this category.
The transactions look like:"
START:Address:Tx:Offset:RESTART:Address[0..4]:Tx/Rx:data[0..n]:STOP"

However there are certain devices which support accesses in
terms of the transactions as follows:
"START:Address:Tx:Txdata[0..n1]:Clock_stretching:
        RESTART:Address:Rx:data[0..n2]"

The Txdata is typically a command and some associated data,
similarly Rxdata could be command status plus some data received
as a response to the command sent.
i2c_read() function has been modified to handle
both types of transactions:
the one that writes only offset/address before read and other that
writes some bytes(more than 4 bytes) before read

To handle the case:
Negative equivalent of length has been passed and
interpreted accordinglt and txdata is being passed in
rxdata buffer

Signed-off-by: Shaveta Leekha <shaveta at freescale.com>
Signed-off-by: Poonam Aggrwal <poonam.aggrwal at freescale.com>
---
 drivers/i2c/fsl_i2c.c |   40 +++++++++++++++++++++++++++++++---------
 1 files changed, 31 insertions(+), 9 deletions(-)

diff --git a/drivers/i2c/fsl_i2c.c b/drivers/i2c/fsl_i2c.c
index 291ad94..14c66d0 100644
--- a/drivers/i2c/fsl_i2c.c
+++ b/drivers/i2c/fsl_i2c.c
@@ -424,17 +424,39 @@ fsl_i2c_read(struct i2c_adapter *adap, u8 dev, uint addr, int alen, u8 *data,
 	int i = -1; /* signal error */
 	u8 *a = (u8*)&addr;
 
-	if (i2c_wait4bus(adap) < 0)
-		return -1;
+	if (alen < 0) {
+		int len = alen * -1;
+		if (i2c_wait4bus(adap) < 0)
+			return -1;
+
+		/* Generate a START and send the Address and
+		 * the Tx Bytes to the slave.
+		 * "START: Address: Write bytes wdata[wlength]"
+		 * It supports writing any number of bytes in contrast
+		 * to the else part, which supports writing address offset
+		 * of upto 4 bytes only.
+		 */
+		if (i2c_write_addr(adap, dev, I2C_WRITE_BIT, 0) != 0)
+			i = __i2c_write(adap, data, len);
+
+		if (i != len)
+			return -1;
+
+		if (length && i2c_write_addr(adap, dev, I2C_READ_BIT, 1) != 0)
+			i = __i2c_read(adap, data, length);
+	} else {
+		if (i2c_wait4bus(adap) < 0)
+			return -1;
 
-	if ((!length || alen > 0)
-	    && i2c_write_addr(adap, dev, I2C_WRITE_BIT, 0) != 0
-	    && __i2c_write(adap, &a[4 - alen], alen) == alen)
-		i = 0; /* No error so far */
+		if ((!length || alen > 0) &&
+		    i2c_write_addr(adap, dev, I2C_WRITE_BIT, 0) != 0  &&
+		    __i2c_write(adap, &a[4 - alen], alen) == alen)
+			i = 0; /* No error so far */
 
-	if (length &&
-	    i2c_write_addr(adap, dev, I2C_READ_BIT, alen ? 1 : 0) != 0)
-		i = __i2c_read(adap, data, length);
+		if (length &&
+		    i2c_write_addr(adap, dev, I2C_READ_BIT, alen ? 1 : 0) != 0)
+			i = __i2c_read(adap, data, length);
+	}
 
 	writeb(I2C_CR_MEN, &device->cr);
 
-- 
1.7.6.GIT




More information about the U-Boot mailing list