[U-Boot] [PATCH v6 8/9] spi: davinci: add support for multiple bus and chip select

[Jagan Teki]

On Fri, Apr 4, 2014 at 10:46 PM, Murali Karicheri <m-karicheri2 at ti.com> wrote:
> Currently davinci spi driver supports only bus 0 cs 0.
> This patch allows driver to support bus 1 and bus 2 with
> configurable number of chip selects. Also defaults are
> selected in a way to avoid regression on other platforms
> that uses davinci spi driver and has only one spi bus.
>
> Signed-off-by: Rex Chang <rchang at ti.com>
> Signed-off-by: Murali Karicheri <m-karicheri2 at ti.com>
> ---
>  drivers/spi/davinci_spi.c |   49 ++++++++++++++++++++++++++++++++++++++++++---
>  drivers/spi/davinci_spi.h |   33 ++++++++++++++++++++++++++++++
>  2 files changed, 79 insertions(+), 3 deletions(-)
>
> diff --git a/drivers/spi/davinci_spi.c b/drivers/spi/davinci_spi.c
> index e3fb321..28fb3a2 100644
> --- a/drivers/spi/davinci_spi.c
> +++ b/drivers/spi/davinci_spi.c
> @@ -32,7 +32,27 @@ struct spi_slave *spi_setup_slave(unsigned int bus, unsigned int cs,
>         if (!ds)
>                 return NULL;
>
> -       ds->regs = (struct davinci_spi_regs *)CONFIG_SYS_SPI_BASE;
> +       ds->slave.bus = bus;
> +       ds->slave.cs = cs;
> +
> +       switch (bus) {
> +       case SPI0_BUS:
> +               ds->regs = (struct davinci_spi_regs *)SPI0_BASE;
> +               break;
> +#ifdef CONFIG_SYS_SPI1
> +       case SPI1_BUS:
> +               ds->regs = (struct davinci_spi_regs *)SPI0_BASE;
> +               break;
> +#endif
> +#ifdef CONFIG_SYS_SPI2
> +       case SPI2_BUS:
> +               ds->regs = (struct davinci_spi_regs *)SPI2_BASE;
> +               break;
> +#endif
> +       default: /* Invalid bus number */
> +               return NULL;
> +       }
> +
>         ds->freq = max_hz;
>
>         return &ds->slave;
> @@ -59,7 +79,7 @@ int spi_claim_bus(struct spi_slave *slave)
>         writel(SPIGCR1_MASTER_MASK | SPIGCR1_CLKMOD_MASK, &ds->regs->gcr1);
>
>         /* CS, CLK, SIMO and SOMI are functional pins */
> -       writel((SPIPC0_EN0FUN_MASK | SPIPC0_CLKFUN_MASK |
> +       writel(((1 << slave->cs) | SPIPC0_CLKFUN_MASK |
>                 SPIPC0_DOFUN_MASK | SPIPC0_DIFUN_MASK), &ds->regs->pc0);
>
>         /* setup format */
> @@ -264,7 +284,30 @@ out:
>
>  int spi_cs_is_valid(unsigned int bus, unsigned int cs)
>  {
> -       return bus == 0 && cs == 0;
> +       int ret = 0;
> +
> +       switch (bus) {
> +       case SPI0_BUS:
> +               if (cs < SPI0_NUM_CS)
> +                       ret = 1;
> +               break;
> +#ifdef CONFIG_SYS_SPI1
> +       case SPI1_BUS:
> +               if (cs < SPI1_NUM_CS)
> +                       ret = 1;
> +               break;
> +#endif
> +#ifdef CONFIG_SYS_SPI2
> +       case SPI2_BUS:
> +               if (cs < SPI2_NUM_CS)
> +                       ret = 1;
> +               break;
> +#endif
> +       default:
> +               /* Invalid bus number. Do nothing */
> +               break;
> +       }
> +       return ret;
>  }
>
>  void spi_cs_activate(struct spi_slave *slave)
> diff --git a/drivers/spi/davinci_spi.h b/drivers/spi/davinci_spi.h
> index 33f69b5..d4612d3 100644
> --- a/drivers/spi/davinci_spi.h
> +++ b/drivers/spi/davinci_spi.h
> @@ -74,6 +74,39 @@ struct davinci_spi_regs {
>  /* SPIDEF */
>  #define SPIDEF_CSDEF0_MASK     BIT(0)
>
> +#define SPI0_BUS               0
> +#define SPI0_BASE              CONFIG_SYS_SPI_BASE
> +/*
> + * Define default SPI0_NUM_CS as 1 for existing platforms that uses this
> + * driver. Platform can configure number of CS using CONFIG_SYS_SPI0_NUM_CS
> + * if more than one CS is supported and by defining CONFIG_SYS_SPI0.
> + */
> +#ifndef CONFIG_SYS_SPI0
> +#define SPI0_NUM_CS            1
> +#else
> +#define SPI0_NUM_CS            CONFIG_SYS_SPI0_NUM_CS
> +#endif
> +
> +/*
> + * define CONFIG_SYS_SPI1 when platform has spi-1 device (bus #1) and
> + * CONFIG_SYS_SPI1_NUM_CS defines number of CS on this bus
> + */
> +#ifdef CONFIG_SYS_SPI1
> +#define SPI1_BUS               1
> +#define SPI1_NUM_CS            CONFIG_SYS_SPI1_NUM_CS
> +#define SPI1_BASE              CONFIG_SYS_SPI1_BASE
> +#endif
> +
> +/*
> + * define CONFIG_SYS_SPI2 when platform has spi-2 device (bus #2) and
> + * CONFIG_SYS_SPI2_NUM_CS defines number of CS on this bus
> + */
> +#ifdef CONFIG_SYS_SPI2
> +#define SPI2_BUS               2
> +#define SPI2_NUM_CS            CONFIG_SYS_SPI2_NUM_CS
> +#define SPI2_BASE              CONFIG_SYS_SPI2_BASE
> +#endif
> +
>  struct davinci_spi_slave {
>         struct spi_slave slave;
>         struct davinci_spi_regs *regs;
> --

Reviewed-by: Jagannadha Sutradharudu Teki <jaganna at xilinx.com>

thanks!
-- 
Jagan.