[U-Boot] [PATCH 04/10][v2] powerpc/mpc85xx:Disable non DDR LAWs before init_law

Prabhakar Kushwaha prabhakar at freescale.com
Tue Apr 8 15:42:46 CEST 2014


Before parsing LAW table i.e. init_law, boot loader should disable all
previous LAWs except DDR LAWs which has been created by previous
pre boot loader during DDR initialization.

Signed-off-by: Prabhakar Kushwaha <prabhakar at freescale.com>
---
Changes for v2: Sending as it is

 arch/powerpc/cpu/mpc8xxx/law.c |   43 +++++++++++++++++++++++++++++++---------
 1 file changed, 34 insertions(+), 9 deletions(-)

diff --git a/arch/powerpc/cpu/mpc8xxx/law.c b/arch/powerpc/cpu/mpc8xxx/law.c
index a401083..0aa6ce1 100644
--- a/arch/powerpc/cpu/mpc8xxx/law.c
+++ b/arch/powerpc/cpu/mpc8xxx/law.c
@@ -221,6 +221,32 @@ int set_ddr_laws(u64 start, u64 sz, enum law_trgt_if id)
 }
 #endif /* not SPL */
 
+void disable_non_ddr_laws(void)
+{
+	int i;
+	int id;
+	for (i = 0; i < FSL_HW_NUM_LAWS; i++) {
+		u32 lawar = in_be32(LAWAR_ADDR(i));
+
+		if (lawar & LAW_EN) {
+			id = (lawar & ~LAW_EN) >> 20;
+			switch (id) {
+			case LAW_TRGT_IF_DDR_1:
+			case LAW_TRGT_IF_DDR_2:
+			case LAW_TRGT_IF_DDR_3:
+			case LAW_TRGT_IF_DDR_4:
+			case LAW_TRGT_IF_DDR_INTRLV:
+			case LAW_TRGT_IF_DDR_INTLV_34:
+			case LAW_TRGT_IF_DDR_INTLV_123:
+			case LAW_TRGT_IF_DDR_INTLV_1234:
+						continue;
+			default:
+						disable_law(i);
+			}
+		}
+	}
+}
+
 void init_laws(void)
 {
 	int i;
@@ -233,6 +259,14 @@ void init_laws(void)
 #error FSL_HW_NUM_LAWS can not be greater than 32 w/o code changes
 #endif
 
+#if !defined(CONFIG_SECURE_BOOT)
+	/*
+	 * if any non DDR LAWs has been created earlier, remove them before
+	 * LAW table is parsed.
+	*/
+	disable_non_ddr_laws();
+#endif
+
 	/*
 	 * Any LAWs that were set up before we booted assume they are meant to
 	 * be around and mark them used.
@@ -244,15 +278,6 @@ void init_laws(void)
 			gd->arch.used_laws |= (1 << i);
 	}
 
-#if (defined(CONFIG_NAND_U_BOOT) && !defined(CONFIG_NAND_SPL)) || \
-	(defined(CONFIG_SPL) && !defined(CONFIG_SPL_BUILD))
-	/*
-	 * in SPL boot we've already parsed the law_table and setup those LAWs
-	 * so don't do it again.
-	 */
-	return;
-#endif
-
 	for (i = 0; i < num_law_entries; i++) {
 		if (law_table[i].index == -1)
 			set_next_law(law_table[i].addr, law_table[i].size,
-- 
1.7.9.5





More information about the U-Boot mailing list