[U-Boot] [PATCH 04/11] MX6: add common SPL configuration

[Tim Harvey]

On Wed, Apr 9, 2014 at 7:55 AM, Nikita Kiryanov <nikita at compulab.co.il> wrote:
> Hi Tim,
>
> On 04/03/2014 09:01 AM, Tim Harvey wrote:> Add a common header which can
> hopefully be shared among imx6 SPL users
>
>>
>> Signed-off-by: Tim Harvey <tharvey at gateworks.com>
>> ---
>>   include/configs/imx6_spl.h | 64
>
> ++++++++++++++++++++++++++++++++++++++++++++++
>>
>>   1 file changed, 64 insertions(+)
>>   create mode 100644 include/configs/imx6_spl.h
>>
>> diff --git a/include/configs/imx6_spl.h b/include/configs/imx6_spl.h
>> new file mode 100644
>> index 0000000..f9bdf55
>> --- /dev/null
>> +++ b/include/configs/imx6_spl.h
>> @@ -0,0 +1,64 @@
>> +/*
>> + * Author: Tim Harvey <tharvey at gateworks.com>
>> + *
>> + * SPDX-License-Identifier:     GPL-2.0+
>> + */
>> +#ifndef __IMX6_SPL_CONFIG_H
>> +#define __IMX6_SPL_CONFIG_H
>> +
>> +#ifdef CONFIG_SPL
>> +
>> +#define CONFIG_SPL_FRAMEWORK
>> +
>> +/*
>> + * IMX6 OCRAM (IRAM) is from 0x00907000 to 0x0093FFFF
>
>
> That's not true for all IMX6 SoCs. On i.MX6 Solo and DualLite it's
> 0x00907000 to 0x0091FFFF.
>
>
>> + *  - we start at 0x00908000 so as to leave some room for IVT/DCD
>> + *  - recommended stack (from IMX6DQRM Figure 8-3) is at 0x0093FFB8
>> + *  - this leaves about 224K for SPL image and stack
>> + */
>> +#define CONFIG_SPL_LDSCRIPT
>> "arch/arm/cpu/armv7/mx6/u-boot-spl.lds"
>> +#define CONFIG_SPL_TEXT_BASE           0x00908000
>> +#define CONFIG_SPL_MAX_SIZE            (128 * 1024)
>
>
> This should be a smaller value if we want this config to apply for
> i.MX6 Solo and DualLite, which have a 68KB OCRAM free area.

Hi Nikita,

Agreed - I just discovered this yesterday. I had tested on an
IMX6DL/SOLO via boot from OTG, but I had not tested those combinations
when booting from flash and indeed they failed.

The 68KB OCRAM free area also assumes that you start at 0x00907000 and
as we start at 0x00908000 to leave room for the IVT+DCD this becomes
65KB

>
>
>> +#define CONFIG_SPL_START_S_PATH                "arch/arm/cpu/armv7"
>> +#define CONFIG_SPL_STACK               0x0093FFB8
>
>
> For i.MX6 Solo and DualLite this address should be lower (recommended
> address is 0x0091FFB8).

Agreed

>
>
>> +#define CONFIG_SPL_LIBCOMMON_SUPPORT
>> +#define CONFIG_SPL_LIBGENERIC_SUPPORT
>> +#define CONFIG_SPL_SERIAL_SUPPORT
>> +#define CONFIG_SPL_I2C_SUPPORT
>> +#define CONFIG_SPL_GPIO_SUPPORT
>> +
>> +/* NAND support */
>> +#if defined(CONFIG_SPL_NAND_SUPPORT)
>> +#define CONFIG_SPL_NAND_MXS
>> +#define CONFIG_SPL_NAND_BASE
>> +#define CONFIG_SPL_DMA_SUPPORT
>> +#endif
>
>
>
> --
> Regards,
> Nikita.

This presents another challenge for SPL NAND as currently my SPL is
~70K. There is a lot of unnecessary code in the mtd nand layer that
I'm including because that layer includes support for both read and
write (I don't need write for SPL) as well as various NAND types (and
I only need BCH).

I'm not sure yet what the best approach is to resolve that. I can either:
 a) add a lot of ifdef's around functions in
drivers/mtd/nand/{nand_base.c,nand_bbt.c} to remove NAND write and non
BCH support for CONFIG_SPL_BUILD
 b) re-write the necessary functionality (code duplication) into
drivers/mtd/nand/mxs_nand_spl.c

Thanks for the review!

Tim