[U-Boot] [PATCH 2/3] board/t208xrdb: Add support of 2-stage NAND/SPI/SD boot
Shengzhou Liu
Shengzhou.Liu at freescale.com
Fri Apr 11 09:42:06 CEST 2014
Add support of 2-stage NAND/SPI/SD boot loader using SPL framework.
PBL initializes the internal CPC-SRAM and copy SPL(96K) to it,
SPL further initializes DDR using SPD and environment and copy u-boot
from SPI/SD/NAND to DDR, finally SPL transfers control to u-boot.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu at freescale.com>
---
board/freescale/t208xrdb/Makefile | 5 ++
board/freescale/t208xrdb/README | 78 ++++++++++++++++++++++-----
board/freescale/t208xrdb/ddr.c | 8 +--
board/freescale/t208xrdb/spl.c | 108 +++++++++++++++++++++++++++++++++++++
board/freescale/t208xrdb/tlb.c | 4 +-
boards.cfg | 6 +--
include/configs/T208xRDB.h | 110 +++++++++++++++++++++++++++++++-------
7 files changed, 282 insertions(+), 37 deletions(-)
create mode 100644 board/freescale/t208xrdb/spl.c
diff --git a/board/freescale/t208xrdb/Makefile b/board/freescale/t208xrdb/Makefile
index 092c9ff..9605f8b 100644
--- a/board/freescale/t208xrdb/Makefile
+++ b/board/freescale/t208xrdb/Makefile
@@ -4,10 +4,15 @@
# SPDX-License-Identifier: GPL-2.0+
#
+ifdef CONFIG_SPL_BUILD
+obj-y += spl.o
+else
obj-$(CONFIG_T2080RDB) += t208xrdb.o
obj-$(CONFIG_T2080RDB) += eth_t208xrdb.o
obj-$(CONFIG_T2080RDB) += cpld.o
obj-$(CONFIG_PCI) += pci.o
+endif
+
obj-y += ddr.o
obj-y += law.o
obj-y += tlb.o
diff --git a/board/freescale/t208xrdb/README b/board/freescale/t208xrdb/README
index 0012c6c..eb9b780 100644
--- a/board/freescale/t208xrdb/README
+++ b/board/freescale/t208xrdb/README
@@ -120,7 +120,7 @@ Start Address End Address Definition Max size
0xEBF00000 0xEBF1FFFF FMAN ucode (alt bank) 128KB
0xEBE00000 0xEBE3FFFF PHY CS4315 firmware (alt bank) 256KB
0xE9300000 0xEBEFFFFF rootfs (current bank) 44MB
-0xE8800000 0xE88FFFFF Hardware device tree (cur bank) 11MB + 512KB
+0xE8800000 0xE88FFFFF Hardware device tree (cur bank) 1MB
0xE8020000 0xE86FFFFF Linux.uImage (current bank) 7MB + 875KB
0xE8000000 0xE801FFFF RCW (current bank) 128KB
@@ -146,7 +146,8 @@ Software configurations and board settings
------------------------------------------
1. NOR boot:
a. build NOR boot image
- $ make T2080RDB
+ $ make T2080RDB_config
+ $ make
b. program u-boot.bin image to NOR flash
=> tftp 1000000 u-boot.bin
=> pro off all;era eff40000 efffffff;cp.b 1000000 eff40000 $filesize
@@ -164,9 +165,9 @@ Software configurations and board settings
2. NAND Boot:
a. build PBL image for NAND boot
$ make T2080RDB_NAND_config
- $ make u-boot.pbl
- b. program u-boot.pbl to NAND flash
- => tftp 1000000 u-boot.pbl
+ $ make
+ b. program u-boot-with-spl-pbl.bin to NAND flash
+ => tftp 1000000 u-boot-with-spl-pbl.bin
=> nand erase 0 d0000
=> nand write 1000000 0 $filesize
set SW1[1:8] = '10000010', SW2[1] = '1', SW3[4] = '1' for NAND boot
@@ -174,9 +175,9 @@ Software configurations and board settings
3. SPI Boot:
a. build PBL image for SPI boot
$ make T2080RDB_SPIFLASH_config
- $ make u-boot.pbl
- b. program u-boot.pbl to SPI flash
- => tftp 1000000 u-boot.pbl
+ $ make
+ b. program u-boot-with-spl-pbl.bin to SPI flash
+ => tftp 1000000 u-boot-with-spl-pbl.bin
=> sf probe 0
=> sf erase 0 d0000
=> sf write 1000000 0 $filesize
@@ -185,13 +186,66 @@ Software configurations and board settings
4. SD Boot:
a. build PBL image for SD boot
$ make T2080RDB_SDCARD_config
- $ make u-boot.pbl
- b. program u-boot.pbl to TF card
- => tftp 1000000 u-boot.pbl
- => mmc write 1000000 8 1650
+ $ make
+ b. program u-boot-with-spl-pbl.bin to micro-SD/TF card
+ => tftp 1000000 u-boot-with-spl-pbl.bin
+ => mmc write 1000000 8 2048
set SW1[1:8] = '00100000', SW2[1] = '0' for SD boot
+2-stage NAND/SPI/SD boot loader
+-------------------------------
+PBL initializes the internal SRAM and copy SPL(192K) in SRAM.
+SPL further initialise DDR using SPD and environment variables
+and copy u-boot(768 KB) from NAND/SPI/SD device to DDR.
+Finally SPL transers control to u-boot for futher booting.
+
+SPL has following features:
+ - Executes within 256K
+ - No relocation required
+
+Run time view of SPL framework
+-------------------------------------------------
+|Area | Address |
+-------------------------------------------------
+|GD, BD | 0xFFFC0000 |
+-------------------------------------------------
+|ENV | 0xFFFC1000 |
+-------------------------------------------------
+|HEAP | 0xFFFC2800 |
+-------------------------------------------------
+|STACK | 0xFFFD0000 |
+-------------------------------------------------
+|U-boot SPL | 0xfffD0000 - 0xfffffffc(192K) |
+-------------------------------------------------
+
+NAND Flash memory Map on T2080RDB
+--------------------------------------------------------------
+Start End Definition Size
+0x000000 0x0FFFFF u-boot img 1MB (2 blocks)
+0x100000 0x17FFFF u-boot env 512KB (1 block)
+0x180000 0x1FFFFF FMAN ucode 512KB (1 block)
+0x200000 0x27FFFF CS4315 ucode 512KB (1 block)
+
+
+Micro SD Card memory Map on T2080RDB
+----------------------------------------------------
+Block #blocks Definition Size
+0x008 2048 u-boot img 1MB
+0x800 0016 u-boot env 8KB
+0x820 0128 FMAN ucode 64KB
+0x8a0 0512 CS4315 ucode 256KB
+
+
+SPI Flash memory Map on T2080RDB
+----------------------------------------------------
+Start End Definition Size
+0x000000 0x0FFFFF u-boot img 1MB
+0x100000 0x101FFF u-boot env 8KB
+0x110000 0x11FFFF FMAN ucode 64KB
+0x120000 0x15FFFF CS4315 ucode 256KB
+
+
How to update the ucode of Cortina CS4315/CS4340 10G PHY
--------------------------------------------------------
=> tftp 1000000 CS4315-CS4340-PHY-ucode.txt
diff --git a/board/freescale/t208xrdb/ddr.c b/board/freescale/t208xrdb/ddr.c
index 01e9173..8a26276 100644
--- a/board/freescale/t208xrdb/ddr.c
+++ b/board/freescale/t208xrdb/ddr.c
@@ -100,13 +100,15 @@ phys_size_t initdram(int board_type)
{
phys_size_t dram_size;
+#if defined(CONFIG_SPL_BUILD) || !defined(CONFIG_RAMBOOT_PBL)
puts("Initializing....using SPD\n");
-
dram_size = fsl_ddr_sdram();
dram_size = setup_ddr_tlbs(dram_size / 0x100000);
dram_size *= 0x100000;
-
- puts(" DDR: ");
+#else
+ /* DDR has been initialised by first stage boot loader */
+ dram_size = fsl_ddr_sdram_size();
+#endif
return dram_size;
}
diff --git a/board/freescale/t208xrdb/spl.c b/board/freescale/t208xrdb/spl.c
new file mode 100644
index 0000000..d1830a6
--- /dev/null
+++ b/board/freescale/t208xrdb/spl.c
@@ -0,0 +1,108 @@
+/* Copyright 2013 Freescale Semiconductor, Inc.
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <malloc.h>
+#include <ns16550.h>
+#include <nand.h>
+#include <i2c.h>
+#include <mmc.h>
+#include <fsl_esdhc.h>
+#include <spi_flash.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+phys_size_t get_effective_memsize(void)
+{
+ return CONFIG_SYS_L3_SIZE;
+}
+
+unsigned long get_board_sys_clk(void)
+{
+ return CONFIG_SYS_CLK_FREQ;
+}
+
+unsigned long get_board_ddr_clk(void)
+{
+ return CONFIG_DDR_CLK_FREQ;
+}
+
+void board_init_f(ulong bootflag)
+{
+ u32 plat_ratio, sys_clk, ccb_clk;
+ ccsr_gur_t *gur = (void *)CONFIG_SYS_MPC85xx_GUTS_ADDR;
+
+ /* Memcpy existing GD at CONFIG_SPL_GD_ADDR */
+ memcpy((void *)CONFIG_SPL_GD_ADDR, (void *)gd, sizeof(gd_t));
+
+ /* Update GD pointer */
+ gd = (gd_t *)(CONFIG_SPL_GD_ADDR);
+
+ console_init_f();
+
+ /* initialize selected port with appropriate baud rate */
+ sys_clk = get_board_sys_clk();
+ plat_ratio = (in_be32(&gur->rcwsr[0]) >> 25) & 0x1f;
+ ccb_clk = sys_clk * plat_ratio / 2;
+
+ NS16550_init((NS16550_t)CONFIG_SYS_NS16550_COM1,
+ ccb_clk / 16 / CONFIG_BAUDRATE);
+
+#if defined(CONFIG_SPL_MMC_BOOT)
+ puts("\nSD boot...\n");
+#elif defined(CONFIG_SPL_SPI_BOOT)
+ puts("\nSPI boot...\n");
+#elif defined(CONFIG_SPL_NAND_BOOT)
+ puts("\nNAND boot...\n");
+#endif
+
+ relocate_code(CONFIG_SPL_RELOC_STACK, (gd_t *)CONFIG_SPL_GD_ADDR, 0x0);
+}
+
+void board_init_r(gd_t *gd, ulong dest_addr)
+{
+ bd_t *bd;
+
+ bd = (bd_t *)(gd + sizeof(gd_t));
+ memset(bd, 0, sizeof(bd_t));
+ gd->bd = bd;
+ bd->bi_memstart = CONFIG_SYS_INIT_L3_ADDR;
+ bd->bi_memsize = CONFIG_SYS_L3_SIZE;
+
+ probecpu();
+ get_clocks();
+ mem_malloc_init(CONFIG_SPL_RELOC_MALLOC_ADDR,
+ CONFIG_SPL_RELOC_MALLOC_SIZE);
+
+#ifndef CONFIG_SPL_NAND_BOOT
+ env_init();
+#endif
+
+#ifdef CONFIG_SPL_MMC_BOOT
+ mmc_initialize(bd);
+#endif
+
+ /* relocate environment function pointers etc. */
+#ifdef CONFIG_SPL_NAND_BOOT
+ nand_spl_load_image(CONFIG_ENV_OFFSET, CONFIG_ENV_SIZE,
+ (uchar *)CONFIG_ENV_ADDR);
+ gd->env_addr = (ulong)(CONFIG_ENV_ADDR);
+ gd->env_valid = 1;
+#else
+ env_relocate();
+#endif
+
+ i2c_init_all();
+
+ gd->ram_size = initdram(0);
+
+#ifdef CONFIG_SPL_MMC_BOOT
+ mmc_boot();
+#elif defined(CONFIG_SPL_SPI_BOOT)
+ spi_boot();
+#elif defined(CONFIG_SPL_NAND_BOOT)
+ nand_boot();
+#endif
+}
diff --git a/board/freescale/t208xrdb/tlb.c b/board/freescale/t208xrdb/tlb.c
index 085d9f5..2ebea36 100644
--- a/board/freescale/t208xrdb/tlb.c
+++ b/board/freescale/t208xrdb/tlb.c
@@ -65,6 +65,7 @@ struct fsl_e_tlb_entry tlb_table[] = {
MAS3_SX|MAS3_SR, MAS2_W|MAS2_G,
0, 2, BOOKE_PAGESZ_256M, 1),
+#ifndef CONFIG_SPL_BUILD
/* *I*G* - PCIe 1, 0x80000000 */
SET_TLB_ENTRY(1, CONFIG_SYS_PCIE1_MEM_VIRT, CONFIG_SYS_PCIE1_MEM_PHYS,
MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
@@ -110,6 +111,7 @@ struct fsl_e_tlb_entry tlb_table[] = {
MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
0, 12, BOOKE_PAGESZ_16M, 1),
#endif
+#endif
#ifdef CONFIG_SYS_DCSRBAR_PHYS
SET_TLB_ENTRY(1, CONFIG_SYS_DCSRBAR, CONFIG_SYS_DCSRBAR_PHYS,
MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
@@ -140,7 +142,7 @@ struct fsl_e_tlb_entry tlb_table[] = {
MAS3_SX|MAS3_SW|MAS3_SR, MAS2_G,
0, 18, BOOKE_PAGESZ_1M, 1),
#endif
-#if defined(CONFIG_SYS_RAMBOOT)
+#if defined(CONFIG_RAMBOOT_PBL) && !defined(CONFIG_SPL_BUILD)
SET_TLB_ENTRY(1, CONFIG_SYS_DDR_SDRAM_BASE, CONFIG_SYS_DDR_SDRAM_BASE,
MAS3_SX|MAS3_SW|MAS3_SR, 0,
0, 19, BOOKE_PAGESZ_2G, 1)
diff --git a/boards.cfg b/boards.cfg
index 4420c46..49f654f 100644
--- a/boards.cfg
+++ b/boards.cfg
@@ -984,9 +984,9 @@ Active powerpc mpc85xx - freescale t208xqds
Active powerpc mpc85xx - freescale t208xqds T2081QDS_NAND T208xQDS:PPC_T2081,RAMBOOT_PBL,RAMBOOT_SPLPBL,NAND
Active powerpc mpc85xx - freescale t208xqds T2081QDS_SRIO_PCIE_BOOT T208xQDS:PPC_T2081,SRIO_PCIE_BOOT_SLAVE,SYS_TEXT_BASE=0xFFF40000
Active powerpc mpc85xx - freescale t208xrdb T2080RDB T208xRDB:PPC_T2080
-Active powerpc mpc85xx - freescale t208xrdb T2080RDB_SDCARD T208xRDB:PPC_T2080,RAMBOOT_PBL,SDCARD,SYS_TEXT_BASE=0xFFF40000
-Active powerpc mpc85xx - freescale t208xrdb T2080RDB_SPIFLASH T208xRDB:PPC_T2080,RAMBOOT_PBL,SPIFLASH,SYS_TEXT_BASE=0xFFF40000
-Active powerpc mpc85xx - freescale t208xrdb T2080RDB_NAND T208xRDB:PPC_T2080,RAMBOOT_PBL,NAND,SYS_TEXT_BASE=0xFFF40000
+Active powerpc mpc85xx - freescale t208xrdb T2080RDB_SDCARD T208xRDB:PPC_T2080,RAMBOOT_PBL,RAMBOOT_SPLPBL,SDCARD
+Active powerpc mpc85xx - freescale t208xrdb T2080RDB_SPIFLASH T208xRDB:PPC_T2080,RAMBOOT_PBL,RAMBOOT_SPLPBL,SPIFLASH
+Active powerpc mpc85xx - freescale t208xrdb T2080RDB_NAND T208xRDB:PPC_T2080,RAMBOOT_PBL,RAMBOOT_SPLPBL,NAND
Active powerpc mpc85xx - freescale t208xrdb T2080RDB_SRIO_PCIE_BOOT T208xRDB:PPC_T2080,SRIO_PCIE_BOOT_SLAVE,SYS_TEXT_BASE=0xFFF40000
Active powerpc mpc85xx - freescale t4qds T4160QDS T4240QDS:PPC_T4160 -
Active powerpc mpc85xx - freescale t4qds T4160QDS_SDCARD T4240QDS:PPC_T4160,RAMBOOT_PBL,SDCARD,SYS_TEXT_BASE=0xFFF40000 -
diff --git a/include/configs/T208xRDB.h b/include/configs/T208xRDB.h
index 728d39c..aacc8b7 100644
--- a/include/configs/T208xRDB.h
+++ b/include/configs/T208xRDB.h
@@ -39,12 +39,76 @@
#define CONFIG_ENV_OVERWRITE
#ifdef CONFIG_RAMBOOT_PBL
-#define CONFIG_RAMBOOT_TEXT_BASE CONFIG_SYS_TEXT_BASE
-#define CONFIG_RESET_VECTOR_ADDRESS 0xfffffffc
#define CONFIG_SYS_FSL_PBL_PBI $(SRCTREE)/board/freescale/t208xrdb/t2080_pbi.cfg
#define CONFIG_SYS_FSL_PBL_RCW $(SRCTREE)/board/freescale/t208xrdb/t2080_rcw.cfg
+
+#define CONFIG_SPL
+#define CONFIG_SPL_MPC8XXX_INIT_DDR_SUPPORT
+#define CONFIG_SPL_ENV_SUPPORT
+#define CONFIG_SPL_SERIAL_SUPPORT
+#define CONFIG_SPL_FLUSH_IMAGE
+#define CONFIG_SPL_TARGET "u-boot-with-spl.bin"
+#define CONFIG_SPL_LIBGENERIC_SUPPORT
+#define CONFIG_SPL_LIBCOMMON_SUPPORT
+#define CONFIG_SPL_I2C_SUPPORT
+#define CONFIG_SPL_DRIVERS_MISC_SUPPORT
+#define CONFIG_FSL_LAW /* Use common FSL init code */
+#define CONFIG_SYS_TEXT_BASE 0x00201000
+#define CONFIG_SPL_TEXT_BASE 0xFFFD0000
+#define CONFIG_SPL_PAD_TO 0x40000
+#define CONFIG_SPL_MAX_SIZE 0x30000
+#define RESET_VECTOR_OFFSET 0x2FFFC
+#define BOOT_PAGE_OFFSET 0x2F000
+#ifdef CONFIG_SPL_BUILD
+#define CONFIG_SPL_SKIP_RELOCATE
+#define CONFIG_SPL_COMMON_INIT_DDR
+#define CONFIG_SYS_CCSR_DO_NOT_RELOCATE
+#define CONFIG_SYS_NO_FLASH
+#endif
+
+#ifdef CONFIG_NAND
+#define CONFIG_SPL_NAND_SUPPORT
+#define CONFIG_SYS_NAND_U_BOOT_SIZE (768 << 10)
+#define CONFIG_SYS_NAND_U_BOOT_DST 0x00200000
+#define CONFIG_SYS_NAND_U_BOOT_START 0x00200000
+#define CONFIG_SYS_NAND_U_BOOT_OFFS (256 << 10)
+#define CONFIG_SYS_LDSCRIPT "arch/powerpc/cpu/mpc85xx/u-boot-nand.lds"
+#define CONFIG_SPL_NAND_BOOT
+#endif
+
+#ifdef CONFIG_SPIFLASH
+#define CONFIG_RESET_VECTOR_ADDRESS 0x200FFC
+#define CONFIG_SPL_SPI_SUPPORT
+#define CONFIG_SPL_SPI_FLASH_SUPPORT
+#define CONFIG_SPL_SPI_FLASH_MINIMAL
+#define CONFIG_SYS_SPI_FLASH_U_BOOT_SIZE (768 << 10)
+#define CONFIG_SYS_SPI_FLASH_U_BOOT_DST (0x00200000)
+#define CONFIG_SYS_SPI_FLASH_U_BOOT_START (0x00200000)
+#define CONFIG_SYS_SPI_FLASH_U_BOOT_OFFS (256 << 10)
+#define CONFIG_SYS_LDSCRIPT "arch/powerpc/cpu/mpc85xx/u-boot.lds"
+#ifndef CONFIG_SPL_BUILD
+#define CONFIG_SYS_MPC85XX_NO_RESETVEC
+#endif
+#define CONFIG_SPL_SPI_BOOT
+#endif
+
+#ifdef CONFIG_SDCARD
+#define CONFIG_RESET_VECTOR_ADDRESS 0x200FFC
+#define CONFIG_SPL_MMC_SUPPORT
+#define CONFIG_SPL_MMC_MINIMAL
+#define CONFIG_SYS_MMC_U_BOOT_SIZE (768 << 10)
+#define CONFIG_SYS_MMC_U_BOOT_DST (0x00200000)
+#define CONFIG_SYS_MMC_U_BOOT_START (0x00200000)
+#define CONFIG_SYS_MMC_U_BOOT_OFFS (260 << 10)
+#define CONFIG_SYS_LDSCRIPT "arch/powerpc/cpu/mpc85xx/u-boot.lds"
+#ifndef CONFIG_SPL_BUILD
+#define CONFIG_SYS_MPC85XX_NO_RESETVEC
+#endif
+#define CONFIG_SPL_MMC_BOOT
#endif
+#endif /* CONFIG_RAMBOOT_PBL */
+
#define CONFIG_SRIO_PCIE_BOOT_MASTER
#ifdef CONFIG_SRIO_PCIE_BOOT_SLAVE
/* Set 1M boot space */
@@ -74,11 +138,7 @@
#define CONFIG_MEM_INIT_VALUE 0xdeadbeef
#endif
-#ifdef CONFIG_SYS_NO_FLASH
-#if !defined(CONFIG_SRIO_PCIE_BOOT_SLAVE) && !defined(CONFIG_RAMBOOT_PBL)
-#define CONFIG_ENV_IS_NOWHERE
-#endif
-#else
+#ifndef CONFIG_SYS_NO_FLASH
#define CONFIG_FLASH_CFI_DRIVER
#define CONFIG_SYS_FLASH_CFI
#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE
@@ -99,11 +159,11 @@
#define CONFIG_ENV_IS_IN_MMC
#define CONFIG_SYS_MMC_ENV_DEV 0
#define CONFIG_ENV_SIZE 0x2000
-#define CONFIG_ENV_OFFSET (512 * 1658)
+#define CONFIG_ENV_OFFSET (512 * 0x800)
#elif defined(CONFIG_NAND)
#define CONFIG_SYS_EXTRA_ENV_RELOC
#define CONFIG_ENV_IS_IN_NAND
-#define CONFIG_ENV_SIZE CONFIG_SYS_NAND_BLOCK_SIZE
+#define CONFIG_ENV_SIZE 0x2000
#define CONFIG_ENV_OFFSET (2 * CONFIG_SYS_NAND_BLOCK_SIZE)
#elif defined(CONFIG_SRIO_PCIE_BOOT_SLAVE)
#define CONFIG_ENV_IS_IN_REMOTE
@@ -129,7 +189,16 @@ unsigned long get_board_ddr_clk(void);
/*
* Config the L3 Cache as L3 SRAM
*/
-#define CONFIG_SYS_INIT_L3_ADDR CONFIG_RAMBOOT_TEXT_BASE
+#define CONFIG_SYS_INIT_L3_ADDR 0xFFFC0000
+#define CONFIG_SYS_L3_SIZE (256 << 10)
+#define CONFIG_SPL_GD_ADDR CONFIG_SYS_INIT_L3_ADDR
+#ifdef CONFIG_NAND
+#define CONFIG_ENV_ADDR (CONFIG_SYS_INIT_L3_ADDR + 4 * 1024)
+#endif
+#define CONFIG_SPL_RELOC_MALLOC_ADDR (CONFIG_SYS_INIT_L3_ADDR + 10 * 1024)
+#define CONFIG_SPL_RELOC_MALLOC_SIZE (50 << 10)
+#define CONFIG_SPL_RELOC_STACK (CONFIG_SYS_INIT_L3_ADDR + 64 * 1024)
+#define CONFIG_SPL_RELOC_STACK_SIZE (20 << 10)
#define CONFIG_SYS_DCSRBAR 0xf0000000
#define CONFIG_SYS_DCSRBAR_PHYS 0xf00000000ull
@@ -301,7 +370,12 @@ unsigned long get_board_ddr_clk(void);
#define CONFIG_SYS_RAMBOOT
#endif
-#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE
+#ifdef CONFIG_SPL_BUILD
+#define CONFIG_SYS_MONITOR_BASE CONFIG_SPL_TEXT_BASE
+#else
+#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */
+#endif
+
#define CONFIG_BOARD_EARLY_INIT_R /* call board_early_init_r function */
#define CONFIG_MISC_INIT_R
#define CONFIG_HWCONFIG
@@ -320,7 +394,7 @@ unsigned long get_board_ddr_clk(void);
#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - \
GENERATED_GBL_DATA_SIZE)
#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
-#define CONFIG_SYS_MONITOR_LEN (512 * 1024)
+#define CONFIG_SYS_MONITOR_LEN (768 * 1024)
#define CONFIG_SYS_MALLOC_LEN (4 * 1024 * 1024)
/*
@@ -516,17 +590,17 @@ unsigned long get_board_ddr_clk(void);
#elif defined(CONFIG_SDCARD)
/*
* PBL SD boot image should stored at 0x1000(8 blocks), the size of the image is
- * about 825KB (1650 blocks), Env is stored after the image, and the env size is
- * 0x2000 (16 blocks), 8 + 1650 + 16 = 1674, enlarge it to 1680.
+ * about 1MB (2048 blocks), Env is stored after the image, and the env size is
+ * 0x2000 (16 blocks), 8 + 2048 + 16 = 2072, enlarge it to 2080.
*/
#define CONFIG_SYS_QE_FMAN_FW_IN_MMC
-#define CONFIG_SYS_QE_FMAN_FW_ADDR (512 * 1680)
-#define CONFIG_CORTINA_FW_ADDR (512 * 1808)
+#define CONFIG_SYS_QE_FMAN_FW_ADDR (512 * 0x820)
+#define CONFIG_CORTINA_FW_ADDR (512 * 0x8a0)
#elif defined(CONFIG_NAND)
#define CONFIG_SYS_QE_FMAN_FW_IN_NAND
-#define CONFIG_SYS_QE_FMAN_FW_ADDR (6 * CONFIG_SYS_NAND_BLOCK_SIZE)
-#define CONFIG_CORTINA_FW_ADDR (7 * CONFIG_SYS_NAND_BLOCK_SIZE)
+#define CONFIG_SYS_QE_FMAN_FW_ADDR (3 * CONFIG_SYS_NAND_BLOCK_SIZE)
+#define CONFIG_CORTINA_FW_ADDR (4 * CONFIG_SYS_NAND_BLOCK_SIZE)
#elif defined(CONFIG_SRIO_PCIE_BOOT_SLAVE)
/*
* Slave has no ucode locally, it can fetch this from remote. When implementing
--
1.8.0
More information about the U-Boot
mailing list