[U-Boot] [PATCH v8 1/2] S5P: Exynos: Add GPIO pin numbering and rename definitions

Akshay Saraswat akshay.s at samsung.com
Wed Apr 16 15:20:56 CEST 2014


Thanks for testing.
Please read inline replies.

>Hello Akshay,
>  04/16/2014 07:32 AM, Akshay Saraswat wrote:
>> This patch includes following changes :
>> * Adds gpio pin numbering support for EXYNOS SOCs.
>>    To have consistent 0..n-1 GPIO numbering the banks are divided
>>    into different parts where ever they have holes in them.
>>
>> * Rename GPIO definitions from GPIO_... to S5P_GPIO_...
>>    These changes were done to enable cmd_gpio for EXYNOS and
>>    cmd_gpio has GPIO_INPUT same as s5p_gpio driver and hence
>>    getting a error during compilation.
>>
>> * Adds support for name to gpio conversion in s5p_gpio to enable
>>    gpio command EXYNOS SoCs. Function has been added to asm/gpio.h
>>    to decode the input gpio name to gpio number.
>>    Example: SMDK5420 # gpio set gpa00
>>
>> Signed-off-by: Leela Krishna Amudala <l.krishna at samsung.com>
>> Signed-off-by: Rajeshwari Shinde <rajeshwari.s at samsung.com>
>> Signed-off-by: Akshay Saraswat <akshay.s at samsung.com>
>> ---
>>   arch/arm/cpu/armv7/exynos/pinmux.c       |  403 +++----
>>   arch/arm/include/asm/arch-exynos/cpu.h   |   17 +-
>>   arch/arm/include/asm/arch-exynos/gpio.h  | 1778 +++++++++++++++++++++++++-----
>>   arch/arm/include/asm/arch-s5pc1xx/gpio.h |  941 +++++++++++++---
>>   board/samsung/arndale/arndale.c          |   11 +-
>>   board/samsung/goni/goni.c                |   26 +-
>>   board/samsung/smdk5250/exynos5-dt.c      |   20 +-
>>   board/samsung/smdk5250/smdk5250.c        |   19 +-
>>   board/samsung/smdk5420/smdk5420.c        |   15 +-
>>   board/samsung/smdkc100/smdkc100.c        |    5 +-
>>   board/samsung/smdkv310/smdkv310.c        |   17 +-
>>   board/samsung/trats/trats.c              |   39 +-
>>   board/samsung/trats2/trats2.c            |   74 +-
>>   board/samsung/universal_c210/universal.c |   51 +-
>>   drivers/gpio/s5p_gpio.c                  |  194 +++-
>>   15 files changed, 2779 insertions(+), 831 deletions(-)
>>
>>
>
>You introduced new method for gpio numbering and I don't know why are 
>you using macro like this:
>"exynos_gpio_get(2, EXYNOS4X12_GPIO_X33)"
>and also new style like only "EXYNOS4X12_GPIO_X33".
>

Even I was wondering why such a macro lies in config file.
But i2c driver is looking for it, so had to modify and keep it.

>
>Those are two different numbers and can't be given to s5p_gpio driver 
>which interprets only new gpio numbering method.
>This code can't work properly.
>

Since, sequential pin number to bank+pin generation is same everywhere,
I thought it's ok to just replace it. Probably the enum mapping has faults.
Need to recalculate.

>
>Please remove old macros and use only proper gpio enum in boards config 
>files.
>We don't need any "get" macro if all gpio numbers are defined explicitly.
>
>You should also modify proper dts files in arch/arm/dts/* .
>
>
>I tested your changes with enums only and after change proper dts file 
>for trats2 there is still data abort.
>So this means that probably enums are not mapped correctly to proper 
>gpio bank addresses.
>
>Do you have an documentation for Exynos4 socs?
>
>I think that this should be checked again with documentation and 
>compiled next to the current code which is simple and just works.
>
>There are also some warnings when checking by checkpatch script.
>

Sure, will fix it. :-)

>
>Thanks
>-- 
>Przemyslaw Marczak
>Samsung R&D Institute Poland
>Samsung Electronics
>p.marczak at samsung.com
>

Regards,
Akshay Saraswat


More information about the U-Boot mailing list