[U-Boot] [PATCH v8 1/2] S5P: Exynos: Add GPIO pin numbering and rename definitions

Przemyslaw Marczak p.marczak at samsung.com
Wed Apr 16 15:48:09 CEST 2014


On 04/16/2014 03:27 PM, Akshay Saraswat wrote:
> Dear Jaehoon Chung,
>
>> Hi, Akshay.
>>
>> Did you test exynos4 board?
>> I have tested your patch-set with the exynos4 board(TRATS2).
>> It didn't work.
>>
>
> No, I didn't test it over Exynos4 boards. I don't have any working.
> Thanks for testing. :-)
>

Did you tested the return gpio bank address for whole Exynos5 gpio enum?

>>
>> Occurred DATA_ABORT.
>> gpio_set_pull(EXYNOS4x12_GPIO_X15,...);
>>
>> Add the comment at below.
>>
>> On 04/16/2014 02:32 PM, Akshay Saraswat wrote:
>>> This patch includes following changes :
>>> * Adds gpio pin numbering support for EXYNOS SOCs.
>>>    To have consistent 0..n-1 GPIO numbering the banks are divided
>>>    into different parts where ever they have holes in them.
>>>
>>> * Rename GPIO definitions from GPIO_... to S5P_GPIO_...
>>>    These changes were done to enable cmd_gpio for EXYNOS and
>>>    cmd_gpio has GPIO_INPUT same as s5p_gpio driver and hence
>>>    getting a error during compilation.
>>>
>>> * Adds support for name to gpio conversion in s5p_gpio to enable
>>>    gpio command EXYNOS SoCs. Function has been added to asm/gpio.h
>>>    to decode the input gpio name to gpio number.
>>>    Example: SMDK5420 # gpio set gpa00
>>>
>>> Signed-off-by: Leela Krishna Amudala <l.krishna at samsung.com>
>>> Signed-off-by: Rajeshwari Shinde <rajeshwari.s at samsung.com>
>>> Signed-off-by: Akshay Saraswat <akshay.s at samsung.com>
>>> ---
>>>   arch/arm/cpu/armv7/exynos/pinmux.c       |  403 +++----
>>>   arch/arm/include/asm/arch-exynos/cpu.h   |   17 +-
>>>   arch/arm/include/asm/arch-exynos/gpio.h  | 1778 +++++++++++++++++++++++++-----
>>>   arch/arm/include/asm/arch-s5pc1xx/gpio.h |  941 +++++++++++++---
>>>   board/samsung/arndale/arndale.c          |   11 +-
>>>   board/samsung/goni/goni.c                |   26 +-
>>>   board/samsung/smdk5250/exynos5-dt.c      |   20 +-
>>>   board/samsung/smdk5250/smdk5250.c        |   19 +-
>>>   board/samsung/smdk5420/smdk5420.c        |   15 +-
>>>   board/samsung/smdkc100/smdkc100.c        |    5 +-
>>>   board/samsung/smdkv310/smdkv310.c        |   17 +-
>>>   board/samsung/trats/trats.c              |   39 +-
>>>   board/samsung/trats2/trats2.c            |   74 +-
>>>   board/samsung/universal_c210/universal.c |   51 +-
>>>   drivers/gpio/s5p_gpio.c                  |  194 +++-
>>>   15 files changed, 2779 insertions(+), 831 deletions(-)
>>>
>>> diff --git a/arch/arm/cpu/armv7/exynos/pinmux.c b/arch/arm/cpu/armv7/exynos/pinmux.c
>>> index 9edb475..e26eb51 100644
>>> --- a/arch/arm/cpu/armv7/exynos/pinmux.c
>>> +++ b/arch/arm/cpu/armv7/exynos/pinmux.c
>>> @@ -13,30 +13,23 @@
>>
>> [..snip..]
>>
>>> -
>>> +#if 0
>>>   /* functions */
>>>   void s5p_gpio_cfg_pin(struct s5p_gpio_bank *bank, int gpio, int cfg);
>>>   void s5p_gpio_direction_output(struct s5p_gpio_bank *bank, int gpio, int en);
>>> @@ -244,6 +29,7 @@ unsigned int s5p_gpio_get_value(struct s5p_gpio_bank *bank, int gpio);
>>>   void s5p_gpio_set_pull(struct s5p_gpio_bank *bank, int gpio, int mode);
>>>   void s5p_gpio_set_drv(struct s5p_gpio_bank *bank, int gpio, int mode);
>>>   void s5p_gpio_set_rate(struct s5p_gpio_bank *bank, int gpio, int mode);
>>> +#endif
>>
>> Why did you use the "#if 0 ~ #endif".
>> If it didn't need to use, it can be removed, isn't?
>>
>
> Apologies, missed it while cleanup. Will remove it.
>
>>
>> Best Regards,
>> Jaehoon Chung
>>
>
> Regards,
> Akshay Saraswat
>

Thank you,
-- 
Przemyslaw Marczak
Samsung R&D Institute Poland
Samsung Electronics
p.marczak at samsung.com


More information about the U-Boot mailing list