[U-Boot] [PATCH 21/26] mpc8260: remove IPHASE4539 board support
Masahiro Yamada
yamada.m at jp.panasonic.com
Mon Dec 15 15:26:26 CET 2014
This board is still a non-generic board.
Signed-off-by: Masahiro Yamada <yamada.m at jp.panasonic.com>
Cc: Wolfgang Grandegger <wg at denx.de>
---
arch/powerpc/cpu/mpc8260/Kconfig | 4 -
board/iphase4539/Kconfig | 9 -
board/iphase4539/MAINTAINERS | 6 -
board/iphase4539/Makefile | 10 -
board/iphase4539/README | 358 -----------------------------
board/iphase4539/flash.c | 474 ---------------------------------------
board/iphase4539/iphase4539.c | 408 ---------------------------------
configs/IPHASE4539_defconfig | 3 -
doc/README.scrapyard | 1 +
include/configs/IPHASE4539.h | 328 ---------------------------
10 files changed, 1 insertion(+), 1600 deletions(-)
delete mode 100644 board/iphase4539/Kconfig
delete mode 100644 board/iphase4539/MAINTAINERS
delete mode 100644 board/iphase4539/Makefile
delete mode 100644 board/iphase4539/README
delete mode 100644 board/iphase4539/flash.c
delete mode 100644 board/iphase4539/iphase4539.c
delete mode 100644 configs/IPHASE4539_defconfig
delete mode 100644 include/configs/IPHASE4539.h
diff --git a/arch/powerpc/cpu/mpc8260/Kconfig b/arch/powerpc/cpu/mpc8260/Kconfig
index 2b3c9c2..56b79ac 100644
--- a/arch/powerpc/cpu/mpc8260/Kconfig
+++ b/arch/powerpc/cpu/mpc8260/Kconfig
@@ -22,9 +22,6 @@ config TARGET_EP82XXM
config TARGET_GW8260
bool "Support gw8260"
-config TARGET_IPHASE4539
- bool "Support IPHASE4539"
-
config TARGET_KM82XX
bool "Support km82xx"
@@ -35,7 +32,6 @@ source "board/cpu86/Kconfig"
source "board/cpu87/Kconfig"
source "board/ep82xxm/Kconfig"
source "board/gw8260/Kconfig"
-source "board/iphase4539/Kconfig"
source "board/keymile/km82xx/Kconfig"
endmenu
diff --git a/board/iphase4539/Kconfig b/board/iphase4539/Kconfig
deleted file mode 100644
index 74594d2..0000000
--- a/board/iphase4539/Kconfig
+++ /dev/null
@@ -1,9 +0,0 @@
-if TARGET_IPHASE4539
-
-config SYS_BOARD
- default "iphase4539"
-
-config SYS_CONFIG_NAME
- default "IPHASE4539"
-
-endif
diff --git a/board/iphase4539/MAINTAINERS b/board/iphase4539/MAINTAINERS
deleted file mode 100644
index ddf6814..0000000
--- a/board/iphase4539/MAINTAINERS
+++ /dev/null
@@ -1,6 +0,0 @@
-IPHASE4539 BOARD
-M: Wolfgang Grandegger <wg at denx.de>
-S: Maintained
-F: board/iphase4539/
-F: include/configs/IPHASE4539.h
-F: configs/IPHASE4539_defconfig
diff --git a/board/iphase4539/Makefile b/board/iphase4539/Makefile
deleted file mode 100644
index 9197b84..0000000
--- a/board/iphase4539/Makefile
+++ /dev/null
@@ -1,10 +0,0 @@
-#
-# (C) Copyright 2006
-# Wolfgang Denk, DENX Software Engineering, wd at denx.de.
-#
-# (C) Copyright 2002 Wolfgang Grandegger <wg at denx.de>
-#
-# SPDX-License-Identifier: GPL-2.0+
-#
-
-obj-y := iphase4539.o flash.o
diff --git a/board/iphase4539/README b/board/iphase4539/README
deleted file mode 100644
index c5146d9..0000000
--- a/board/iphase4539/README
+++ /dev/null
@@ -1,358 +0,0 @@
-
-This file contains basic information on the port of U-Boot to IPHASE4539
-(Interphase 4539 T1/E1/J1 PMC Communications Controller).
-All the changes fit in the common U-Boot infrastructure, providing a new
-IPHASE4539-specific entry in makefiles. To build U-Boot for IPHASE4539,
-type "make IPHASE4539_config", edit the "include/config_IPHASE4539.h"
-file if necessary, then type "make".
-
-
-Common file modifications:
---------------------------
-
-The following common files have been modified by this project:
-(starting from the ppcboot-1.1.5/ directory)
-
-MAKEALL - IPHASE4539 entry added
-Makefile - IPHASE4539_config entry added
-
-
-New files:
-----------
-
-The following new files have been added by this project:
-(starting from the ppcboot-1.1.5/ directory)
-
-board/iphase4539/ - board-specific directory
-board/iphase4539/Makefile - board-specific makefile
-board/iphase4539/config.mk - config file
-board/iphase4539/flash.c - flash driver (for AM29LV033C)
-board/iphase4539/ppcboot.lds - linker script
-board/iphase4539/iphase4539.c - ioport and memory initialization
-include/config_IPHASE4539.h - main configuration file
-
-
-New configuration options:
---------------------------
-
-CONFIG_IPHASE4539
-
- Main board-specific option (should be defined for IPHASE4539).
-
-
-Acceptance criteria tests:
---------------------------
-
-The following tests have been conducted to validate the port of U-Boot
-to IPHASE4539:
-
-1. Operation on serial console:
-
-With SMC1 defined as console in the main configuration file, the U-Boot
-output appeared on the serial terminal connected to the 2.5mm stereo jack
-connector as follows:
-
-------------------------------------------------------------------------------
-=> help
-base - print or set address offset
-bdinfo - print Board Info structure
-bootm - boot application image from memory
-bootp - boot image via network using BootP/TFTP protocol
-bootd - boot default, i.e., run 'bootcmd'
-cmp - memory compare
-coninfo - print console devices and informations
-cp - memory copy
-crc32 - checksum calculation
-dcache - enable or disable data cache
-echo - echo args to console
-erase - erase FLASH memory
-flinfo - print FLASH memory information
-go - start application at address 'addr'
-help - print online help
-icache - enable or disable instruction cache
-iminfo - print header information for application image
-loadb - load binary file over serial line (kermit mode)
-loads - load S-Record file over serial line
-loop - infinite loop on address range
-md - memory display
-mm - memory modify (auto-incrementing)
-mtest - simple RAM test
-mw - memory write (fill)
-nm - memory modify (constant address)
-printenv- print environment variables
-protect - enable or disable FLASH write protection
-rarpboot- boot image via network using RARP/TFTP protocol
-reset - Perform RESET of the CPU
-run - run commands in an environment variable
-saveenv - save environment variables to persistent storage
-setenv - set environment variables
-sleep - delay execution for some time
-source - run script from memory
-tftpboot- boot image via network using TFTP protocol
- and env variables ipaddr and serverip
-version - print monitor version
-? - alias for 'help'
-=>
-------------------------------------------------------------------------------
-
-
-2. Flash driver operation
-
-The following sequence was performed to test the "flinfo" command:
-
-------------------------------------------------------------------------------
-=> flinfo
-
-Bank # 1: AMD AM29LV033C (32 Mbit, uniform sectors)
- Size: 4 MB in 64 Sectors
- Sector Start Addresses:
- FF800000 (RO) FF810000 (RO) FF820000 FF830000 FF840000
- FF850000 FF860000 FF870000 FF880000 FF890000
- FF8A0000 FF8B0000 FF8C0000 FF8D0000 FF8E0000
- FF8F0000 FF900000 FF910000 FF920000 FF930000
- FF940000 FF950000 FF960000 FF970000 FF980000
- FF990000 FF9A0000 FF9B0000 FF9C0000 FF9D0000
- FF9E0000 FF9F0000 FFA00000 FFA10000 FFA20000
- FFA30000 FFA40000 FFA50000 FFA60000 FFA70000
- FFA80000 FFA90000 FFAA0000 FFAB0000 FFAC0000
- FFAD0000 FFAE0000 FFAF0000 FFB00000 (RO) FFB10000 (RO)
- FFB20000 (RO) FFB30000 (RO) FFB40000 FFB50000 FFB60000
- FFB70000 FFB80000 FFB90000 FFBA0000 FFBB0000
- FFBC0000 FFBD0000 FFBE0000 FFBF0000
-------------------------------------------------------------------------------
-
-Note: the Hardware Configuration Word (HWC) of the 8260 is on the
-first sector of the flash and should not be touched. The U-Boot
-environment variables are stored on second sector and U-Boot
-starts at the address 0xFFB00000.
-
-
-The following sequence was performed to test the erase command:
-
-------------------------------------------------------------------------------
-=> cp 0 ff880000 10
-Copy to Flash... done
-=> md ff880000 20
-ff880000: ff000000 60000000 60000000 7c7f1b78 ....`...`...|..x
-ff880010: 7c9e2378 7cbd2b78 7cdc3378 7cfb3b78 |.#x|.+x|.3x|.;x
-ff880020: 3b000000 4811e0f5 48003719 480036a5 ;...H...H.7.H.6.
-ff880030: 480036f9 48003731 48005c5d 7c7a1b78 H.6.H.71H.\]|z.x
-ff880040: ffffffff ffffffff ffffffff ffffffff ................
-ff880050: ffffffff ffffffff ffffffff ffffffff ................
-ff880060: ffffffff ffffffff ffffffff ffffffff ................
-ff880070: ffffffff ffffffff ffffffff ffffffff ................
-=> erase ff880000 ff88ffff
-Erase Flash from 0xff880000 to 0xff88ffff
-.. done
-Erased 1 sectors
-=> md ff880000
-ff880000: ffffffff ffffffff ffffffff ffffffff ................
-ff880010: ffffffff ffffffff ffffffff ffffffff ................
-ff880020: ffffffff ffffffff ffffffff ffffffff ................
-ff880030: ffffffff ffffffff ffffffff ffffffff ................
-ff880040: ffffffff ffffffff ffffffff ffffffff ................
-ff880050: ffffffff ffffffff ffffffff ffffffff ................
-ff880060: ffffffff ffffffff ffffffff ffffffff ................
-ff880070: ffffffff ffffffff ffffffff ffffffff ................
-=> cp 0 ff880000 10
-Copy to Flash... done
-=> md ff880000 20
-ff880000: ff000000 60000000 60000000 7c7f1b78 ....`...`...|..x
-ff880010: 7c9e2378 7cbd2b78 7cdc3378 7cfb3b78 |.#x|.+x|.3x|.;x
-ff880020: 3b000000 4811e0f5 48003719 480036a5 ;...H...H.7.H.6.
-ff880030: 480036f9 48003731 48005c5d 7c7a1b78 H.6.H.71H.\]|z.x
-ff880040: ffffffff ffffffff ffffffff ffffffff ................
-ff880050: ffffffff ffffffff ffffffff ffffffff ................
-ff880060: ffffffff ffffffff ffffffff ffffffff ................
-ff880070: ffffffff ffffffff ffffffff ffffffff ................
-=> erase 1:8
-Erase Flash Sectors 8-8 in Bank # 1
-.. done
-=> md ff880000 20
-ff880000: ffffffff ffffffff ffffffff ffffffff ................
-ff880010: ffffffff ffffffff ffffffff ffffffff ................
-ff880020: ffffffff ffffffff ffffffff ffffffff ................
-ff880030: ffffffff ffffffff ffffffff ffffffff ................
-ff880040: ffffffff ffffffff ffffffff ffffffff ................
-ff880050: ffffffff ffffffff ffffffff ffffffff ................
-ff880060: ffffffff ffffffff ffffffff ffffffff ................
-ff880070: ffffffff ffffffff ffffffff ffffffff ................
-=> cp 0 ff880000 10
-Copy to Flash... done
-=> cp 0 ff890000 10
-=> md ff880000 20
-ff880000: ff000000 60000000 60000000 7c7f1b78 ....`...`...|..x
-ff880010: 7c9e2378 7cbd2b78 7cdc3378 7cfb3b78 |.#x|.+x|.3x|.;x
-ff880020: 3b000000 4811e0f5 48003719 480036a5 ;...H...H.7.H.6.
-ff880030: 480036f9 48003731 48005c5d 7c7a1b78 H.6.H.71H.\]|z.x
-ff880040: ffffffff ffffffff ffffffff ffffffff ................
-ff880050: ffffffff ffffffff ffffffff ffffffff ................
-ff880060: ffffffff ffffffff ffffffff ffffffff ................
-ff880070: ffffffff ffffffff ffffffff ffffffff ................
-=> md ff890000
-ff890000: ff000000 60000000 60000000 7c7f1b78 ....`...`...|..x
-ff890010: 7c9e2378 7cbd2b78 7cdc3378 7cfb3b78 |.#x|.+x|.3x|.;x
-ff890020: 3b000000 4811e0f5 48003719 480036a5 ;...H...H.7.H.6.
-ff890030: 480036f9 48003731 48005c5d 7c7a1b78 H.6.H.71H.\]|z.x
-ff890040: ffffffff ffffffff ffffffff ffffffff ................
-ff890050: ffffffff ffffffff ffffffff ffffffff ................
-ff890060: ffffffff ffffffff ffffffff ffffffff ................
-ff890070: ffffffff ffffffff ffffffff ffffffff ................
-=> erase 1:8-9
-Erase Flash Sectors 8-9 in Bank # 1
-.... done
-=> md ff880000 20
-ff880000: ffffffff ffffffff ffffffff ffffffff ................
-ff880010: ffffffff ffffffff ffffffff ffffffff ................
-ff880020: ffffffff ffffffff ffffffff ffffffff ................
-ff880030: ffffffff ffffffff ffffffff ffffffff ................
-ff880040: ffffffff ffffffff ffffffff ffffffff ................
-ff880050: ffffffff ffffffff ffffffff ffffffff ................
-ff880060: ffffffff ffffffff ffffffff ffffffff ................
-ff880070: ffffffff ffffffff ffffffff ffffffff ................
-=> md ff890000
-ff890000: ffffffff ffffffff ffffffff ffffffff ................
-ff890010: ffffffff ffffffff ffffffff ffffffff ................
-ff890020: ffffffff ffffffff ffffffff ffffffff ................
-ff890030: ffffffff ffffffff ffffffff ffffffff ................
-ff890040: ffffffff ffffffff ffffffff ffffffff ................
-ff890050: ffffffff ffffffff ffffffff ffffffff ................
-ff890060: ffffffff ffffffff ffffffff ffffffff ................
-ff890070: ffffffff ffffffff ffffffff ffffffff ................
-=>
-------------------------------------------------------------------------------
-
-
-The following sequence was performed to test the Flash programming commands:
-
-------------------------------------------------------------------------------
-=> erase ff880000 ff88ffff
-Erase Flash from 0xff880000 to 0xff88ffff
-.. done
-Erased 1 sectors
-=> cp 0 ff880000 10
-Copy to Flash... done
-=> md 0 20
-00000000: ff000000 60000000 60000000 7c7f1b78 ....`...`...|..x
-00000010: 7c9e2378 7cbd2b78 7cdc3378 7cfb3b78 |.#x|.+x|.3x|.;x
-00000020: 3b000000 4811e0f5 48003719 480036a5 ;...H...H.7.H.6.
-00000030: 480036f9 48003731 48005c5d 7c7a1b78 H.6.H.71H.\]|z.x
-00000040: 3c83c000 2c040000 40823378 7c0000a6 <...,... at .3x|...
-00000050: 60000030 7c1b03a6 3c00c000 600035ec `..0|...<...`.5.
-00000060: 7c1a03a6 4c000064 00000000 00000000 |...L..d........
-00000070: 00000000 00000000 00000000 00000000 ................
-=> md ff880000 20
-ff880000: ff000000 60000000 60000000 7c7f1b78 ....`...`...|..x
-ff880010: 7c9e2378 7cbd2b78 7cdc3378 7cfb3b78 |.#x|.+x|.3x|.;x
-ff880020: 3b000000 4811e0f5 48003719 480036a5 ;...H...H.7.H.6.
-ff880030: 480036f9 48003731 48005c5d 7c7a1b78 H.6.H.71H.\]|z.x
-ff880040: ffffffff ffffffff ffffffff ffffffff ................
-ff880050: ffffffff ffffffff ffffffff ffffffff ................
-ff880060: ffffffff ffffffff ffffffff ffffffff ................
-ff880070: ffffffff ffffffff ffffffff ffffffff ................
-=>
-------------------------------------------------------------------------------
-
-
-The following sequence was performed to test storage of the environment
-variables in Flash:
-
-------------------------------------------------------------------------------
-=> setenv foo bar
-=> saveenv
-Un-Protected 1 sectors
-Erasing Flash...
-.. done
-Erased 1 sectors
-Saving Environment to Flash...
-Protected 1 sectors
-=> reset
-...
-=> printenv
-...
-foo=bar
-...
-Environment size: 339/65532 bytes
-=>
-------------------------------------------------------------------------------
-
-
-The following sequence was performed to test image download and run over
-Ethernet interface (both interfaces were tested):
-
-------------------------------------------------------------------------------
-=> tftpboot 40000 hello_world.bin
-ARP broadcast 1
-TFTP from server 10.0.0.1; our IP address is 10.0.0.8
-Filename 'hello_world.bin'.
-Load address: 0x40000
-Loading: #############
-done
-Bytes transferred = 65932 (1018c hex)
-=> go 40004
-## Starting application at 0x00040004 ...
-Hello World
-argc = 1
-argv[0] = "40004"
-argv[1] = "<NULL>"
-Hit any key to exit ...
-
-## Application terminated, rc = 0x0
-=>
-------------------------------------------------------------------------------
-
-
-3. Known Problems
-
-None for the moment.
-
-
-----------------------------------------------------------------------------
-U-Boot and Linux for Interphase 4539 T1/E1/J1 PMC Communications Controller
-----------------------------------------------------------------------------
-
-U-Boot:
-
- Configure and make U-Boot:
-
- $ cd <path>/u-boot
- $ make IPHASE4539_config
- $ make dep
- $ make
- $ cp -p u-boot.bin /tftpboot
-
- Load u-boot.bin into the Flash memory at 0xffb00000.
-
-
-Linux:
-
- Configure and make Linux:
-
- $ cd <patch>/linux-2.4
- $ make IPHASE4539_config
- $ make oldconfig
- $ make dep
- $ make uImage
- $ cp -p arch/powerpc/mbxboot/uImage /tftpboot
-
- Load uImage via tftp and boot it.
-
-
-Flash organisation:
-
- The following preliminary layout of the Flash memory
- is defined:
-
- 0xff800000 ( 0 - 64 kB): Hardware Configuration Word.
- 0xff810000 ( 64 kB - 128 kB): U-Boot Environment.
- 0xff820000 ( 128 kB - 3 MB): RAMdisk.
- 0xffb00000 ( 3 MB - 3328 kB): U-Boot.
- 0xffb40000 (3328 KB - 4 MB): Linux Kernel.
-
-
-For further information concerning U-Boot and Linux please consult
-the "DENX U-Boot and Linux Guide".
-
-
-(C) 2002 Wolfgang Grandegger, DENX Software Engineering, wg at denx.de
-===================================================================
diff --git a/board/iphase4539/flash.c b/board/iphase4539/flash.c
deleted file mode 100644
index 3c2dad6..0000000
--- a/board/iphase4539/flash.c
+++ /dev/null
@@ -1,474 +0,0 @@
-/*
- * (C) Copyright 2001
- * Josh Huber <huber at mclx.com>, Mission Critical Linux, Inc.
- *
- * (C) Copyright 2002
- * Wolfgang Denk, DENX Software Engineering, wd at denx.de.
- *
- * Adapted for Interphase 4539 by Wolfgang Grandegger <wg at denx.de>.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#include <config.h>
-#include <common.h>
-#include <flash.h>
-#include <asm/io.h>
-
-flash_info_t flash_info[CONFIG_SYS_MAX_FLASH_BANKS];
-
-extern int hwc_flash_size(void);
-static ulong flash_get_size (u32 addr, flash_info_t *info);
-static int flash_get_offsets (u32 base, flash_info_t *info);
-static int write_word (flash_info_t *info, ulong dest, ulong data);
-static void flash_reset (u32 addr);
-
-#define out8(a,v) *(volatile unsigned char*)(a) = v
-#define in8(a) *(volatile unsigned char*)(a)
-#define in32(a) *(volatile unsigned long*)(a)
-#define iobarrier_rw() eieio()
-
-unsigned long flash_init (void)
-{
- unsigned int i;
- unsigned long flash_size = 0;
- unsigned long bank_size;
- unsigned int bank = 0;
-
- /* Init: no FLASHes known */
- for (i=0; i < CONFIG_SYS_MAX_FLASH_BANKS; ++i) {
- flash_info[i].flash_id = FLASH_UNKNOWN;
- flash_info[i].sector_count = 0;
- flash_info[i].size = 0;
- }
-
- /* Initialise the BOOT Flash */
- if (bank == CONFIG_SYS_MAX_FLASH_BANKS) {
- puts ("Warning: not all Flashes are initialised !");
- return flash_size;
- }
-
- bank_size = flash_get_size (CONFIG_SYS_FLASH_BASE, flash_info + bank);
- if (bank_size) {
-#if CONFIG_SYS_MONITOR_BASE >= CONFIG_SYS_FLASH_BASE && \
- CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE + CONFIG_SYS_MAX_FLASH_SIZE
- /* monitor protection ON by default */
- flash_protect(FLAG_PROTECT_SET,
- CONFIG_SYS_MONITOR_BASE,
- CONFIG_SYS_MONITOR_BASE + monitor_flash_len - 1,
- flash_info + bank);
-#endif
-
-#ifdef CONFIG_ENV_IS_IN_FLASH
- /* ENV protection ON by default */
- flash_protect(FLAG_PROTECT_SET,
- CONFIG_ENV_ADDR,
- CONFIG_ENV_ADDR + CONFIG_ENV_SECT_SIZE - 1,
- flash_info + bank);
-#endif
-
- /* HWC protection ON by default */
- flash_protect(FLAG_PROTECT_SET,
- CONFIG_SYS_FLASH_BASE,
- CONFIG_SYS_FLASH_BASE + 0x10000 - 1,
- flash_info + bank);
-
- flash_size += bank_size;
- bank++;
- } else {
- puts ("Warning: the BOOT Flash is not initialised !");
- }
-
- return flash_size;
-}
-
-/*
- * The following code cannot be run from FLASH!
- */
-static ulong flash_get_size (u32 addr, flash_info_t *info)
-{
- volatile uchar value;
-#if 0
- int i;
-#endif
-
- /* Write auto select command: read Manufacturer ID */
- out8(addr + 0x0555, 0xAA);
- iobarrier_rw();
- udelay(10);
- out8(addr + 0x02AA, 0x55);
- iobarrier_rw();
- udelay(10);
- out8(addr + 0x0555, 0x90);
- iobarrier_rw();
- udelay(10);
-
- value = in8(addr);
- iobarrier_rw();
- udelay(10);
- switch (value | (value << 16)) {
- case AMD_MANUFACT:
- info->flash_id = FLASH_MAN_AMD;
- break;
-
- case FUJ_MANUFACT:
- info->flash_id = FLASH_MAN_FUJ;
- break;
-
- default:
- info->flash_id = FLASH_UNKNOWN;
- flash_reset (addr);
- return 0;
- }
-
- value = in8(addr + 1); /* device ID */
- iobarrier_rw();
-
- switch (value) {
- case AMD_ID_LV033C:
- info->flash_id += FLASH_AM033C;
- info->size = hwc_flash_size();
- if (info->size > CONFIG_SYS_MAX_FLASH_SIZE) {
- printf("U-Boot supports only %d MB\n",
- CONFIG_SYS_MAX_FLASH_SIZE);
- info->size = CONFIG_SYS_MAX_FLASH_SIZE;
- }
- info->sector_count = info->size / 0x10000;
- break; /* => 4 MB */
-
- default:
- info->flash_id = FLASH_UNKNOWN;
- flash_reset (addr);
- return (0); /* => no or unknown flash */
-
- }
-
- if (!flash_get_offsets (addr, info)) {
- flash_reset (addr);
- return 0;
- }
-
-#if 0
- /* check for protected sectors */
- for (i = 0; i < info->sector_count; i++) {
- /* read sector protection at sector address, (A7 .. A0) = 0x02 */
- /* D0 = 1 if protected */
- value = in8(info->start[i] + 2);
- iobarrier_rw();
- info->protect[i] = (value & 1) != 0;
- }
-#endif
-
- /*
- * Reset bank to read mode
- */
- flash_reset (addr);
-
- return (info->size);
-}
-
-static int flash_get_offsets (u32 base, flash_info_t *info)
-{
- unsigned int i, size;
-
- switch (info->flash_id & FLASH_TYPEMASK) {
- case FLASH_AM033C:
- /* set sector offsets for uniform sector type */
- size = info->size / info->sector_count;
- for (i = 0; i < info->sector_count; i++) {
- info->start[i] = base + i * size;
- }
- break;
- default:
- return 0;
- }
-
- return 1;
-}
-
-int flash_erase (flash_info_t *info, int s_first, int s_last)
-{
- volatile u32 addr = info->start[0];
- int flag, prot, sect, l_sect;
- ulong start, now, last;
-
- if (s_first < 0 || s_first > s_last) {
- if (info->flash_id == FLASH_UNKNOWN) {
- printf ("- missing\n");
- } else {
- printf ("- no sectors to erase\n");
- }
- return 1;
- }
-
- if (info->flash_id == FLASH_UNKNOWN ||
- info->flash_id > FLASH_AMD_COMP) {
- printf ("Can't erase unknown flash type %08lx - aborted\n",
- info->flash_id);
- return 1;
- }
-
- prot = 0;
- for (sect=s_first; sect<=s_last; ++sect) {
- if (info->protect[sect]) {
- prot++;
- }
- }
-
- if (prot) {
- printf ("- Warning: %d protected sectors will not be erased!\n",
- prot);
- } else {
- printf ("\n");
- }
-
- l_sect = -1;
-
- /* Disable interrupts which might cause a timeout here */
- flag = disable_interrupts();
-
- out8(addr + 0x555, 0xAA);
- iobarrier_rw();
- out8(addr + 0x2AA, 0x55);
- iobarrier_rw();
- out8(addr + 0x555, 0x80);
- iobarrier_rw();
- out8(addr + 0x555, 0xAA);
- iobarrier_rw();
- out8(addr + 0x2AA, 0x55);
- iobarrier_rw();
-
- /* Start erase on unprotected sectors */
- for (sect = s_first; sect<=s_last; sect++) {
- if (info->protect[sect] == 0) { /* not protected */
- addr = info->start[sect];
- out8(addr, 0x30);
- iobarrier_rw();
- l_sect = sect;
- }
- }
-
- /* re-enable interrupts if necessary */
- if (flag)
- enable_interrupts();
-
- /* wait at least 80us - let's wait 1 ms */
- udelay (1000);
-
- /*
- * We wait for the last triggered sector
- */
- if (l_sect < 0)
- goto DONE;
-
- start = get_timer (0);
- last = start;
- addr = info->start[l_sect];
- while ((in8(addr) & 0x80) != 0x80) {
- if ((now = get_timer(start)) > CONFIG_SYS_FLASH_ERASE_TOUT) {
- printf ("Timeout\n");
- return 1;
- }
- /* show that we're waiting */
- if ((now - last) > 1000) { /* every second */
- putc ('.');
- last = now;
- }
- iobarrier_rw();
- }
-
-DONE:
- /* reset to read mode */
- flash_reset (info->start[0]);
-
- printf (" done\n");
- return 0;
-}
-
-/*
- * Copy memory to flash, returns:
- * 0 - OK
- * 1 - write timeout
- * 2 - Flash not erased
- */
-int write_buff (flash_info_t *info, uchar *src, ulong addr, ulong cnt)
-{
- ulong cp, wp, data;
- int i, l, rc;
-
- wp = (addr & ~3); /* get lower word aligned address */
-
- /*
- * handle unaligned start bytes
- */
- if ((l = addr - wp) != 0) {
- data = 0;
- for (i=0, cp=wp; i<l; ++i, ++cp) {
- data = (data << 8) | (*(uchar *)cp);
- }
- for (; i<4 && cnt>0; ++i) {
- data = (data << 8) | *src++;
- --cnt;
- ++cp;
- }
- for (; cnt==0 && i<4; ++i, ++cp) {
- data = (data << 8) | (*(uchar *)cp);
- }
-
- if ((rc = write_word(info, wp, data)) != 0) {
- return (rc);
- }
- wp += 4;
- }
-
- /*
- * handle word aligned part
- */
- while (cnt >= 4) {
- data = 0;
- for (i=0; i<4; ++i) {
- data = (data << 8) | *src++;
- }
- if ((rc = write_word(info, wp, data)) != 0) {
- return (rc);
- }
- wp += 4;
- cnt -= 4;
- }
-
- if (cnt == 0) {
- return (0);
- }
-
- /*
- * handle unaligned tail bytes
- */
- data = 0;
- for (i=0, cp=wp; i<4 && cnt>0; ++i, ++cp) {
- data = (data << 8) | *src++;
- --cnt;
- }
- for (; i<4; ++i, ++cp) {
- data = (data << 8) | (*(uchar *)cp);
- }
-
- return (write_word(info, wp, data));
-}
-
-/*
- * Write a word to Flash, returns:
- * 0 - OK
- * 1 - write timeout
- * 2 - Flash not erased
- */
-static int write_word (flash_info_t *info, ulong dest, ulong data)
-{
- volatile u32 addr = info->start[0];
- ulong start;
- int flag, i;
-
- /* Check if Flash is (sufficiently) erased */
- if ((in32(dest) & data) != data) {
- return (2);
- }
- /* Disable interrupts which might cause a timeout here */
- flag = disable_interrupts();
-
- /* first, perform an unlock bypass command to speed up flash writes */
- out8(addr + 0x555, 0xAA);
- iobarrier_rw();
- out8(addr + 0x2AA, 0x55);
- iobarrier_rw();
- out8(addr + 0x555, 0x20);
- iobarrier_rw();
-
- /* write each byte out */
- for (i = 0; i < 4; i++) {
- char *data_ch = (char *)&data;
- out8(addr, 0xA0);
- iobarrier_rw();
- out8(dest+i, data_ch[i]);
- iobarrier_rw();
- udelay(10); /* XXX */
- }
-
- /* we're done, now do an unlock bypass reset */
- out8(addr, 0x90);
- iobarrier_rw();
- out8(addr, 0x00);
- iobarrier_rw();
-
- /* re-enable interrupts if necessary */
- if (flag)
- enable_interrupts();
-
- /* data polling for D7 */
- start = get_timer (0);
- while ((in32(dest) & 0x80808080) != (data & 0x80808080)) {
- if (get_timer(start) > CONFIG_SYS_FLASH_WRITE_TOUT) {
- return (1);
- }
- iobarrier_rw();
- }
-
- flash_reset (addr);
-
- return (0);
-}
-
-/*
- * Reset bank to read mode
- */
-static void flash_reset (u32 addr)
-{
- out8(addr, 0xF0); /* reset bank */
- iobarrier_rw();
-}
-
-void flash_print_info (flash_info_t *info)
-{
- int i;
-
- if (info->flash_id == FLASH_UNKNOWN) {
- printf ("missing or unknown FLASH type\n");
- return;
- }
-
- switch (info->flash_id & FLASH_VENDMASK) {
- case FLASH_MAN_AMD: printf ("AMD "); break;
- case FLASH_MAN_FUJ: printf ("FUJITSU "); break;
- case FLASH_MAN_BM: printf ("BRIGHT MICRO "); break;
- default: printf ("Unknown Vendor "); break;
- }
-
- switch (info->flash_id & FLASH_TYPEMASK) {
- case FLASH_AM033C: printf ("AM29LV033C (32 Mbit, uniform sectors)\n");
- break;
- default: printf ("Unknown Chip Type\n");
- break;
- }
-
- if (info->size % 0x100000 == 0) {
- printf (" Size: %ld MB in %d Sectors\n",
- info->size / 0x100000, info->sector_count);
- }
- else if (info->size % 0x400 == 0) {
- printf (" Size: %ld KB in %d Sectors\n",
- info->size / 0x400, info->sector_count);
- }
- else {
- printf (" Size: %ld B in %d Sectors\n",
- info->size, info->sector_count);
- }
-
- printf (" Sector Start Addresses:");
- for (i=0; i<info->sector_count; ++i) {
- if ((i % 5) == 0)
- printf ("\n ");
- printf (" %08lX%s",
- info->start[i],
- info->protect[i] ? " (RO)" : " "
- );
- }
- printf ("\n");
-}
diff --git a/board/iphase4539/iphase4539.c b/board/iphase4539/iphase4539.c
deleted file mode 100644
index d40d2b6..0000000
--- a/board/iphase4539/iphase4539.c
+++ /dev/null
@@ -1,408 +0,0 @@
-/*
- * (C) Copyright 2002 Wolfgang Grandegger <wg at denx.de>
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#include <common.h>
-#include <ioports.h>
-#include <mpc8260.h>
-#include <asm/io.h>
-#include <asm/immap_8260.h>
-
-int hwc_flash_size (void);
-int hwc_local_sdram_size (void);
-int hwc_main_sdram_size (void);
-int hwc_serial_number (void);
-int hwc_mac_address (char *str);
-int hwc_manufact_date (char *str);
-int seeprom_read (int addr, uchar * data, int size);
-
-/*
- * I/O Port configuration table
- *
- * if conf is 1, then that port pin will be configured at boot time
- * according to the five values podr/pdir/ppar/psor/pdat for that entry
- *
- * The port definitions are taken from the old firmware (see
- * also SYS/H/4539.H):
- *
- * ppar psor pdir podr pdat
- * PA: 0x02ffffff 0x02c00000 0xfc403fe6 0x00000000 0x02403fc0
- * PB: 0x0fffdeb0 0x000000b0 0x0f032347 0x00000000 0x0f000290
- * PC: 0x030ffa55 0x030f0040 0xbcf005ea 0x00000000 0xc0c0ba7d
- * PD: 0x09c04e3c 0x01000e3c 0x0a7ff1c3 0x00000000 0x00ce0ae9
- */
-const iop_conf_t iop_conf_tab[4][32] = {
-
- /* Port A configuration */
- { /* conf ppar psor pdir podr pdat */
- {0, 1, 0, 0, 0, 0}, /* PA31 FCC1_TXENB SLAVE */
- {0, 1, 0, 1, 0, 0}, /* PA30 FCC1_TXCLAV SLAVE */
- {0, 1, 0, 1, 0, 0}, /* PA29 FCC1_TXSOC */
- {0, 1, 0, 0, 0, 0}, /* PA28 FCC1_RXENB SLAVE */
- {0, 1, 0, 0, 0, 0}, /* PA27 FCC1_RXSOC */
- {0, 1, 0, 1, 0, 0}, /* PA26 FCC1_RXCLAV SLAVE */
- {0, 1, 0, 1, 0, 1}, /* PA25 FCC1_TXD0 */
- {0, 1, 0, 1, 0, 1}, /* PA24 FCC1_TXD1 */
- {0, 1, 0, 1, 0, 1}, /* PA23 FCC1_TXD2 */
- {0, 1, 0, 1, 0, 1}, /* PA22 FCC1_TXD3 */
- {0, 1, 0, 1, 0, 1}, /* PA21 FCC1_TXD4 */
- {0, 1, 0, 1, 0, 1}, /* PA20 FCC1_TXD5 */
- {0, 1, 0, 1, 0, 1}, /* PA19 FCC1_TXD6 */
- {0, 1, 0, 1, 0, 1}, /* PA18 FCC1_TXD7 */
- {0, 1, 0, 0, 0, 0}, /* PA17 FCC1_RXD7 */
- {0, 1, 0, 0, 0, 0}, /* PA16 FCC1_RXD6 */
- {0, 1, 0, 0, 0, 0}, /* PA15 FCC1_RXD5 */
- {0, 1, 0, 0, 0, 0}, /* PA14 FCC1_RXD4 */
- {0, 1, 0, 0, 0, 0}, /* PA13 FCC1_RXD3 */
- {0, 1, 0, 0, 0, 0}, /* PA12 FCC1_RXD2 */
- {0, 1, 0, 0, 0, 0}, /* PA11 FCC1_RXD1 */
- {0, 1, 0, 0, 0, 0}, /* PA10 FCC1_RXD0 */
- {0, 1, 1, 1, 0, 1}, /* PA9 TDMA1_L1TXD */
- {0, 1, 1, 0, 0, 0}, /* PA8 TDMA1_L1RXD */
- {0, 0, 0, 0, 0, 0}, /* PA7 CONFIG0 */
- {0, 1, 1, 0, 0, 1}, /* PA6 TDMA1_L1RSYNC */
- {0, 0, 0, 1, 0, 0}, /* PA5 FCC2:RxAddr[2] */
- {0, 0, 0, 1, 0, 0}, /* PA4 FCC2:RxAddr[1] */
- {0, 0, 0, 1, 0, 0}, /* PA3 FCC2:RxAddr[0] */
- {0, 0, 0, 1, 0, 0}, /* PA2 FCC2:TxAddr[0] */
- {0, 0, 0, 1, 0, 0}, /* PA1 FCC2:TxAddr[1] */
- {0, 0, 0, 1, 0, 0} /* PA0 FCC2:TxAddr[2] */
- },
- /* Port B configuration */
- { /* conf ppar psor pdir podr pdat */
- {0, 0, 0, 1, 0, 0}, /* PB31 FCC2_RXSOC */
- {0, 0, 0, 1, 0, 0}, /* PB30 FCC2_TXSOC */
- {0, 0, 0, 1, 0, 0}, /* PB29 FCC2_RXCLAV */
- {0, 0, 0, 0, 0, 0}, /* PB28 CONFIG2 */
- {0, 1, 1, 0, 0, 1}, /* PB27 FCC2_TXD0 */
- {0, 1, 1, 0, 0, 0}, /* PB26 FCC2_TXD1 */
- {0, 0, 0, 1, 0, 0}, /* PB25 FCC2_TXD4 */
- {0, 1, 1, 0, 0, 1}, /* PB24 FCC2_TXD5 */
- {0, 0, 0, 1, 0, 0}, /* PB23 FCC2_TXD6 */
- {0, 1, 0, 1, 0, 1}, /* PB22 FCC2_TXD7 */
- {0, 1, 0, 0, 0, 0}, /* PB21 FCC2_RXD7 */
- {0, 1, 0, 0, 0, 0}, /* PB20 FCC2_RXD6 */
- {0, 1, 0, 0, 0, 0}, /* PB19 FCC2_RXD5 */
- {0, 0, 0, 1, 0, 0}, /* PB18 FCC2_RXD4 */
- {1, 1, 0, 0, 0, 0}, /* PB17 FCC3_RX_DV */
- {1, 1, 0, 0, 0, 0}, /* PB16 FCC3_RX_ER */
- {1, 1, 0, 1, 0, 0}, /* PB15 FCC3_TX_ER */
- {1, 1, 0, 1, 0, 0}, /* PB14 FCC3_TX_EN */
- {1, 1, 0, 0, 0, 0}, /* PB13 FCC3_COL */
- {1, 1, 0, 0, 0, 0}, /* PB12 FCC3_CRS */
- {1, 1, 0, 0, 0, 0}, /* PB11 FCC3_RXD3 */
- {1, 1, 0, 0, 0, 0}, /* PB10 FCC3_RXD2 */
- {1, 1, 0, 0, 0, 0}, /* PB9 FCC3_RXD1 */
- {1, 1, 0, 0, 0, 0}, /* PB8 FCC3_RXD0 */
- {1, 1, 0, 1, 0, 1}, /* PB7 FCC3_TXD0 */
- {1, 1, 0, 1, 0, 1}, /* PB6 FCC3_TXD1 */
- {1, 1, 0, 1, 0, 1}, /* PB5 FCC3_TXD2 */
- {1, 1, 0, 1, 0, 1}, /* PB4 FCC3_TXD3 */
- {0, 0, 0, 0, 0, 0}, /* PB3 */
- {0, 0, 0, 0, 0, 0}, /* PB2 */
- {0, 0, 0, 0, 0, 0}, /* PB1 */
- {0, 0, 0, 0, 0, 0}, /* PB0 */
- },
- /* Port C configuration */
- { /* conf ppar psor pdir podr pdat */
- {0, 1, 0, 0, 0, 1}, /* PC31 CLK1 */
- {0, 0, 0, 1, 0, 0}, /* PC30 U1MASTER_N */
- {0, 1, 0, 0, 0, 1}, /* PC29 CLK3 */
- {0, 0, 0, 1, 0, 1}, /* PC28 -MT90220_RST */
- {0, 1, 0, 0, 0, 1}, /* PC27 CLK5 */
- {0, 0, 0, 1, 0, 1}, /* PC26 -QUADFALC_RST */
- {0, 1, 1, 1, 0, 1}, /* PC25 BRG4 */
- {1, 0, 0, 1, 0, 0}, /* PC24 MDIO */
- {1, 0, 0, 1, 0, 0}, /* PC23 MDC */
- {0, 1, 0, 0, 0, 1}, /* PC22 CLK10 */
- {0, 0, 0, 1, 0, 0}, /* PC21 */
- {0, 1, 0, 0, 0, 1}, /* PC20 CLK12 */
- {0, 1, 0, 0, 0, 1}, /* PC19 CLK13 */
- {1, 1, 0, 0, 0, 1}, /* PC18 CLK14 */
- {0, 1, 0, 0, 0, 0}, /* PC17 CLK15 */
- {1, 1, 0, 0, 0, 1}, /* PC16 CLK16 */
- {0, 1, 1, 0, 0, 0}, /* PC15 FCC1_TXADDR0 SLAVE */
- {0, 1, 1, 0, 0, 0}, /* PC14 FCC1_RXADDR0 SLAVE */
- {0, 1, 1, 0, 0, 0}, /* PC13 FCC1_TXADDR1 SLAVE */
- {0, 1, 1, 0, 0, 0}, /* PC12 FCC1_RXADDR1 SLAVE */
- {0, 0, 0, 1, 0, 0}, /* PC11 FCC2_RXD2 */
- {0, 0, 0, 1, 0, 0}, /* PC10 FCC2_RXD3 */
- {0, 0, 0, 1, 0, 1}, /* PC9 LTMODE */
- {0, 0, 0, 1, 0, 1}, /* PC8 SELSYNC */
- {0, 1, 1, 0, 0, 0}, /* PC7 FCC1_TXADDR2 SLAVE */
- {0, 1, 1, 0, 0, 0}, /* PC6 FCC1_RXADDR2 SLAVE */
- {0, 0, 0, 1, 0, 0}, /* PC5 FCC2_TXCLAV MASTER */
- {0, 0, 0, 1, 0, 0}, /* PC4 FCC2_RXENB MASTER */
- {0, 0, 0, 1, 0, 0}, /* PC3 FCC2_TXD2 */
- {0, 0, 0, 1, 0, 0}, /* PC2 FCC2_TXD3 */
- {0, 0, 0, 0, 0, 1}, /* PC1 PTMC -PTEENB */
- {0, 0, 0, 1, 0, 1}, /* PC0 COMCLK_N */
- },
- /* Port D configuration */
- { /* conf ppar psor pdir podr pdat */
- {0, 0, 0, 1, 0, 1}, /* PD31 -CAM_RST */
- {0, 0, 0, 1, 0, 0}, /* PD30 FCC2_TXENB */
- {0, 1, 1, 0, 0, 0}, /* PD29 FCC1_RXADDR3 SLAVE */
- {0, 1, 1, 0, 0, 1}, /* PD28 TDMC1_L1TXD */
- {0, 1, 1, 0, 0, 0}, /* PD27 TDMC1_L1RXD */
- {0, 1, 1, 0, 0, 1}, /* PD26 TDMC1_L1RSYNC */
- {0, 0, 0, 1, 0, 1}, /* PD25 LED0 -OFF */
- {0, 0, 0, 1, 0, 1}, /* PD24 LED5 -OFF */
- {1, 0, 0, 1, 0, 1}, /* PD23 -LXT971_RST */
- {0, 1, 1, 0, 0, 1}, /* PD22 TDMA2_L1TXD */
- {0, 1, 1, 0, 0, 0}, /* PD21 TDMA2_L1RXD */
- {0, 1, 1, 0, 0, 1}, /* PD20 TDMA2_L1RSYNC */
- {0, 0, 0, 1, 0, 0}, /* PD19 FCC2_TXADDR3 */
- {0, 0, 0, 1, 0, 0}, /* PD18 FCC2_RXADDR3 */
- {0, 1, 0, 1, 0, 0}, /* PD17 BRG2 */
- {0, 0, 0, 1, 0, 0}, /* PD16 */
- {0, 0, 0, 1, 0, 0}, /* PD15 PT2TO1 */
- {0, 0, 0, 1, 0, 1}, /* PD14 PT4TO3 */
- {0, 0, 0, 1, 0, 1}, /* PD13 -SWMODE */
- {0, 0, 0, 1, 0, 1}, /* PD12 -PTMODE */
- {0, 0, 0, 1, 0, 0}, /* PD11 FCC2_RXD0 */
- {0, 0, 0, 1, 0, 0}, /* PD10 FCC2_RXD1 */
- {1, 1, 0, 1, 0, 1}, /* PD9 SMC1_SMTXD */
- {1, 1, 0, 0, 0, 1}, /* PD8 SMC1_SMRXD */
- {0, 1, 1, 0, 0, 0}, /* PD7 FCC1_TXADDR3 SLAVE */
- {0, 0, 0, 1, 0, 0}, /* PD6 IMAMODE */
- {0, 0, 0, 0, 0, 0}, /* PD5 CONFIG2 */
- {0, 1, 0, 1, 0, 0}, /* PD4 BRG8 */
- {0, 0, 0, 0, 0, 0}, /* PD3 */
- {0, 0, 0, 0, 0, 0}, /* PD2 */
- {0, 0, 0, 0, 0, 0}, /* PD1 */
- {0, 0, 0, 0, 0, 0}, /* PD0 */
- }
-};
-
-phys_size_t initdram (int board_type)
-{
- volatile immap_t *immap = (immap_t *) CONFIG_SYS_IMMR;
- volatile memctl8260_t *memctl = &immap->im_memctl;
- volatile uchar *base;
- ulong maxsize;
- int i;
-
- memctl->memc_psrt = CONFIG_SYS_PSRT;
- memctl->memc_mptpr = CONFIG_SYS_MPTPR;
-
-#ifndef CONFIG_SYS_RAMBOOT
- immap->im_siu_conf.sc_ppc_acr = 0x00000026;
- immap->im_siu_conf.sc_ppc_alrh = 0x01276345;
- immap->im_siu_conf.sc_ppc_alrl = 0x89ABCDEF;
- immap->im_siu_conf.sc_lcl_acr = 0x00000000;
- immap->im_siu_conf.sc_lcl_alrh = 0x01234567;
- immap->im_siu_conf.sc_lcl_alrl = 0x89ABCDEF;
- immap->im_siu_conf.sc_tescr1 = 0x00004000;
- immap->im_siu_conf.sc_ltescr1 = 0x00004000;
-
- /* Init Main SDRAM */
-#define OP_VALUE 0x404A241A
-#define OP_VALUE_M (OP_VALUE & 0x87FFFFFF);
- base = (uchar *) CONFIG_SYS_SDRAM_BASE;
- memctl->memc_psdmr = 0x28000000 | OP_VALUE_M;
- *base = 0xFF;
- memctl->memc_psdmr = 0x08000000 | OP_VALUE_M;
- for (i = 0; i < 8; i++)
- *base = 0xFF;
- memctl->memc_psdmr = 0x18000000 | OP_VALUE_M;
- *(base + 0x110) = 0xFF;
- memctl->memc_psdmr = OP_VALUE;
- memctl->memc_lsdmr = 0x4086A522;
- *base = 0xFF;
-
- /* We must be able to test a location outsize the maximum legal size
- * to find out THAT we are outside; but this address still has to be
- * mapped by the controller. That means, that the initial mapping has
- * to be (at least) twice as large as the maximum expected size.
- */
- maxsize = (1 + (~memctl->memc_or1 | 0x7fff)) / 2;
-
- maxsize = get_ram_size((long *)base, maxsize);
-
- memctl->memc_or1 |= ~(maxsize - 1);
-
- if (maxsize != hwc_main_sdram_size ())
- printf ("Oops: memory test has not found all memory!\n");
-#endif
-
- icache_enable ();
- /* return total ram size of SDRAM */
- return (maxsize);
-}
-
-int checkboard (void)
-{
- char string[32];
-
- hwc_manufact_date (string);
-
- printf ("Board: Interphase 4539 (#%d %s)\n",
- hwc_serial_number (),
- string);
-
-#ifdef DEBUG
- printf ("Manufacturing date: %s\n", string);
- printf ("Serial number : %d\n", hwc_serial_number ());
- printf ("FLASH size : %d MB\n", hwc_flash_size () >> 20);
- printf ("Main SDRAM size : %d MB\n", hwc_main_sdram_size () >> 20);
- printf ("Local SDRAM size : %d MB\n", hwc_local_sdram_size () >> 20);
- hwc_mac_address (string);
- printf ("MAC address : %s\n", string);
-#endif
-
- return 0;
-}
-
-int misc_init_r (void)
-{
- char *s, str[32];
- int num;
-
- if ((s = getenv ("serial#")) == NULL &&
- (num = hwc_serial_number ()) != -1) {
- sprintf (str, "%06d", num);
- setenv ("serial#", str);
- }
- if ((s = getenv ("ethaddr")) == NULL && hwc_mac_address (str) == 0) {
- setenv ("ethaddr", str);
- }
- return (0);
-}
-
-/***************************************************************
- * We take some basic Hardware Configuration Parameter from the
- * Serial EEPROM conected to the PSpan bridge. We keep it as
- * simple as possible.
- */
-int hwc_flash_size (void)
-{
- uchar byte;
-
- if (!seeprom_read (0x40, &byte, sizeof (byte))) {
- switch ((byte >> 2) & 0x3) {
- case 0x1:
- return 0x0400000;
- break;
- case 0x2:
- return 0x0800000;
- break;
- case 0x3:
- return 0x1000000;
- default:
- return 0x0100000;
- }
- }
- return -1;
-}
-int hwc_local_sdram_size (void)
-{
- uchar byte;
-
- if (!seeprom_read (0x40, &byte, sizeof (byte))) {
- switch ((byte & 0x03)) {
- case 0x1:
- return 0x0800000;
- case 0x2:
- return 0x1000000;
- default:
- return 0; /* not present */
- }
- }
- return -1;
-}
-int hwc_main_sdram_size (void)
-{
- uchar byte;
-
- if (!seeprom_read (0x41, &byte, sizeof (byte))) {
- return 0x1000000 << ((byte >> 5) & 0x7);
- }
- return -1;
-}
-int hwc_serial_number (void)
-{
- int sn = -1;
-
- if (!seeprom_read (0xa0, (uchar *) &sn, sizeof (sn))) {
- sn = cpu_to_le32 (sn);
- }
- return sn;
-}
-int hwc_mac_address (char *str)
-{
- char mac[6];
-
- if (!seeprom_read (0xb0, (uchar *)mac, sizeof (mac))) {
- sprintf (str, "%02x:%02x:%02x:%02x:%02x:%02x\n",
- mac[0], mac[1], mac[2], mac[3], mac[4], mac[5]);
- } else {
- strcpy (str, "ERROR");
- return -1;
- }
- return 0;
-}
-int hwc_manufact_date (char *str)
-{
- uchar byte;
- int value;
-
- if (seeprom_read (0x92, &byte, sizeof (byte)))
- goto out;
- value = byte;
- if (seeprom_read (0x93, &byte, sizeof (byte)))
- goto out;
- value += byte << 8;
- sprintf (str, "%02d/%02d/%04d",
- value & 0x1F, (value >> 5) & 0xF,
- 1980 + ((value >> 9) & 0x1FF));
- return 0;
-
- out:
- strcpy (str, "ERROR");
- return -1;
-}
-
-#define PSPAN_ADDR 0xF0020000
-#define EEPROM_REG 0x408
-#define EEPROM_READ_CMD 0xA000
-#define PSPAN_WRITE(a,v) \
- *((volatile unsigned long *)(PSPAN_ADDR+(a))) = v; eieio()
-#define PSPAN_READ(a) \
- *((volatile unsigned long *)(PSPAN_ADDR+(a)))
-
-int seeprom_read (int addr, uchar * data, int size)
-{
- ulong val, cmd;
- int i;
-
- for (i = 0; i < size; i++) {
-
- cmd = EEPROM_READ_CMD;
- cmd |= ((addr + i) << 24) & 0xff000000;
-
- /* Wait for ACT to authorize write */
- while ((val = PSPAN_READ (EEPROM_REG)) & 0x80)
- eieio ();
-
- /* Write command */
- PSPAN_WRITE (EEPROM_REG, cmd);
-
- /* Wait for data to be valid */
- while ((val = PSPAN_READ (EEPROM_REG)) & 0x80)
- eieio ();
- /* Do it twice, first read might be erratic */
- while ((val = PSPAN_READ (EEPROM_REG)) & 0x80)
- eieio ();
-
- /* Read error */
- if (val & 0x00000040) {
- return -1;
- } else {
- data[i] = (val >> 16) & 0xff;
- }
- }
- return 0;
-}
diff --git a/configs/IPHASE4539_defconfig b/configs/IPHASE4539_defconfig
deleted file mode 100644
index d49ea52..0000000
--- a/configs/IPHASE4539_defconfig
+++ /dev/null
@@ -1,3 +0,0 @@
-CONFIG_PPC=y
-CONFIG_MPC8260=y
-CONFIG_TARGET_IPHASE4539=y
diff --git a/doc/README.scrapyard b/doc/README.scrapyard
index 7f76aae..af4b00c 100644
--- a/doc/README.scrapyard
+++ b/doc/README.scrapyard
@@ -12,6 +12,7 @@ The list should be sorted in reverse chronological order.
Board Arch CPU Commit Removed Last known maintainer/contact
=================================================================================================
+IPHASE4539 powerpc mpc8260 - - Wolfgang Grandegger <wg at denx.de>
muas3001 powerpc mpc8260 - - Heiko Schocher <hs at denx.de>
PM825 powerpc mpc8260 - - Wolfgang Denk <wd at denx.de>
PM826 powerpc mpc8260 - - Wolfgang Denk <wd at denx.de>
diff --git a/include/configs/IPHASE4539.h b/include/configs/IPHASE4539.h
deleted file mode 100644
index e402075..0000000
--- a/include/configs/IPHASE4539.h
+++ /dev/null
@@ -1,328 +0,0 @@
-/*
- * (C) Copyright 2002 Wolfgang Grandegger <wg at denx.de>
- *
- * This file is based on similar values for other boards found in
- * other U-Boot config files, mainly tqm8260.h and mpc8260ads.h.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-/*
- * Config header file for a Interphase 4539 PMC, 64 MB SDRAM, 4MB Flash.
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-/*-----------------------------------------------------------------------
- * High Level Configuration Options
- * (easy to change)
- */
-
-#define CONFIG_IPHASE4539 1 /* ...on a Interphase 4539 PMC */
-
-#define CONFIG_SYS_TEXT_BASE 0xffb00000
-
-#define CONFIG_CPM2 1 /* Has a CPM2 */
-
-/*-----------------------------------------------------------------------
- * select serial console configuration
- *
- * if either CONFIG_CONS_ON_SMC or CONFIG_CONS_ON_SCC is selected, then
- * CONFIG_CONS_INDEX must be set to the channel number (1-2 for SMC, 1-4
- * for SCC).
- *
- * if CONFIG_CONS_NONE is defined, then the serial console routines must
- * defined elsewhere (for example, on the cogent platform, there are serial
- * ports on the motherboard which are used for the serial console - see
- * cogent/cma101/serial.[ch]).
- */
-#define CONFIG_CONS_ON_SMC /* define if console on SMC */
-#undef CONFIG_CONS_ON_SCC /* define if console on SCC */
-#undef CONFIG_CONS_NONE /* define if console on something else */
-#define CONFIG_CONS_INDEX 1 /* which serial channel for console */
-
-/*-----------------------------------------------------------------------
- * select ethernet configuration
- *
- * if either CONFIG_ETHER_ON_SCC or CONFIG_ETHER_ON_FCC is selected, then
- * CONFIG_ETHER_INDEX must be set to the channel number (1-4 for SCC, 1-3
- * for FCC)
- *
- * if CONFIG_ETHER_NONE is defined, then either the ethernet routines must be
- * defined elsewhere (as for the console), or CONFIG_CMD_NET must be unset.
- */
-#undef CONFIG_ETHER_ON_SCC /* define if ether on SCC */
-#define CONFIG_ETHER_ON_FCC /* define if ether on FCC */
-#undef CONFIG_ETHER_NONE /* define if ether on something else */
-#define CONFIG_ETHER_INDEX 3 /* which channel for ether */
-
-#if defined(CONFIG_ETHER_ON_FCC) && (CONFIG_ETHER_INDEX == 3)
-
-/*-----------------------------------------------------------------------
- * - Rx-CLK is CLK14
- * - Tx-CLK is CLK16
- * - Select bus for bd/buffers (see 28-13)
- * - Half duplex
- */
-# define CONFIG_SYS_CMXFCR_MASK3 (CMXFCR_FC3 | CMXFCR_RF3CS_MSK | CMXFCR_TF3CS_MSK)
-# define CONFIG_SYS_CMXFCR_VALUE3 (CMXFCR_RF3CS_CLK14 | CMXFCR_TF3CS_CLK16)
-# define CONFIG_SYS_CPMFCR_RAMTYPE 0
-# define CONFIG_SYS_FCC_PSMR (FCC_PSMR_FDE|FCC_PSMR_LPB)
-
-#endif /* CONFIG_ETHER_ON_FCC, CONFIG_ETHER_INDEX */
-
-/* other options */
-
-#define CONFIG_8260_CLKIN 66666666 /* in Hz */
-#define CONFIG_BAUDRATE 19200
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_SUBNETMASK
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_BOOTFILESIZE
-
-/*
- * select i2c support configuration
- *
- * Supported configurations are {none, software, hardware} drivers.
- * If the software driver is chosen, there are some additional
- * configuration items that the driver uses to drive the port pins.
- */
-#define CONFIG_SYS_I2C
-#define CONFIG_SYS_I2C_SOFT /* I2C bit-banged */
-#define CONFIG_SYS_I2C_SOFT_SPEED 400000
-#define CONFIG_SYS_I2C_SOFT_SLAVE 0x7F
-/*
- * Software (bit-bang) I2C driver configuration
- */
-#define I2C_PORT 3 /* Port A=0, B=1, C=2, D=3 */
-#define I2C_ACTIVE (iop->pdir |= 0x00010000)
-#define I2C_TRISTATE (iop->pdir &= ~0x00010000)
-#define I2C_READ ((iop->pdat & 0x00010000) != 0)
-#define I2C_SDA(bit) if(bit) iop->pdat |= 0x00010000; \
- else iop->pdat &= ~0x00010000
-#define I2C_SCL(bit) if(bit) iop->pdat |= 0x00020000; \
- else iop->pdat &= ~0x00020000
-#define I2C_DELAY udelay(5) /* 1/4 I2C clock duration */
-
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-
-
-#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */
-#define CONFIG_BOOTCOMMAND "bootm 100000" /* autoboot command */
-#define CONFIG_BOOTARGS "root=/dev/ram rw"
-
-#if defined(CONFIG_CMD_KGDB)
-#undef CONFIG_KGDB_ON_SMC /* define if kgdb on SMC */
-#define CONFIG_KGDB_ON_SCC /* define if kgdb on SCC */
-#undef CONFIG_KGDB_NONE /* define if kgdb on something else */
-#define CONFIG_KGDB_INDEX 2 /* which serial channel for kgdb */
-#define CONFIG_KGDB_BAUDRATE 115200 /* speed to run kgdb serial port at */
-#endif
-
-#undef CONFIG_WATCHDOG /* disable platform specific watchdog */
-
-/*-----------------------------------------------------------------------
- * Miscellaneous configurable options
- */
-#define CONFIG_SYS_LONGHELP /* undef to save memory */
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
-#else
-#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
-#endif
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
-#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
-#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
-
-#define CONFIG_SYS_MEMTEST_START 0x00100000 /* memtest works on */
-#define CONFIG_SYS_MEMTEST_END 0x00F00000 /* 1 ... 15 MB in DRAM */
-
-#define CONFIG_CLOCKS_IN_MHZ 1 /* clocks passed to Linux in MHz */
- /* for versions < 2.4.5-pre5 */
-
-#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */
-
-#define CONFIG_SYS_RESET_ADDRESS 0x04400000
-
-#define CONFIG_MISC_INIT_R 1 /* We need misc_init_r() */
-
-/*-----------------------------------------------------------------------
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
-
-/*-----------------------------------------------------------------------
- * Start addresses for the final memory configuration (Setup by the
- * startup code). Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0.
- */
-#define CONFIG_SYS_SDRAM_BASE 0x00000000
-#define CONFIG_SYS_FLASH_BASE 0xFF800000
-
-#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE
-#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */
-#define CONFIG_SYS_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */
-
-/*-----------------------------------------------------------------------
- * FLASH organization
- */
-#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max num of memory banks */
-#define CONFIG_SYS_MAX_FLASH_SECT 64 /* max num of sects on one chip */
-#define CONFIG_SYS_MAX_FLASH_SIZE (CONFIG_SYS_MAX_FLASH_SECT * 0x10000) /* 4 MB */
-
-#define CONFIG_SYS_FLASH_ERASE_TOUT 2400000 /* Flash Erase Timeout (in ms) */
-#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (in ms) */
-
-/* Environment in FLASH, there is little space left in Serial EEPROM */
-#define CONFIG_ENV_IS_IN_FLASH 1
-#define CONFIG_ENV_SECT_SIZE 0x10000 /* We use one complete sector */
-#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + 0x10000) /* 2. sector */
-
-
-/*-----------------------------------------------------------------------
- * Hard Reset Configuration Words
- *
- * if you change bits in the HRCW, you must also change the CONFIG_SYS_*
- * defines for the various registers affected by the HRCW e.g. changing
- * HRCW_DPPCxx requires you to also change CONFIG_SYS_SIUMCR.
- */
-#define CONFIG_SYS_HRCW_MASTER ( ( HRCW_BPS01 | HRCW_EBM ) |\
- ( HRCW_L2CPC10 | HRCW_ISB110 ) |\
- ( HRCW_MMR11 | HRCW_APPC10 ) |\
- ( HRCW_CS10PC01 | HRCW_MODCK_H0101 ) \
- ) /* 0x14863245 */
-
-/* no slaves */
-#define CONFIG_SYS_HRCW_SLAVE1 0
-#define CONFIG_SYS_HRCW_SLAVE2 0
-#define CONFIG_SYS_HRCW_SLAVE3 0
-#define CONFIG_SYS_HRCW_SLAVE4 0
-#define CONFIG_SYS_HRCW_SLAVE5 0
-#define CONFIG_SYS_HRCW_SLAVE6 0
-#define CONFIG_SYS_HRCW_SLAVE7 0
-
-/*-----------------------------------------------------------------------
- * Internal Memory Mapped Register
- */
-#define CONFIG_SYS_IMMR 0xFF000000 /* We keep original value */
-
-/*-----------------------------------------------------------------------
- * Definitions for initial stack pointer and data area (in DPRAM)
- */
-#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_IMMR
-#define CONFIG_SYS_INIT_RAM_SIZE 0x4000 /* Size of used area in DPRAM */
-#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
-
-/*-----------------------------------------------------------------------
- * Cache Configuration
- */
-#define CONFIG_SYS_CACHELINE_SIZE 32 /* For MPC8260 CPU */
-#if defined(CONFIG_CMD_KGDB)
-# define CONFIG_SYS_CACHELINE_SHIFT 5 /* log base 2 of the above value */
-#endif
-
-/*-----------------------------------------------------------------------
- * HIDx - Hardware Implementation-dependent Registers 2-11
- *-----------------------------------------------------------------------
- * HID0 also contains cache control.
- *
- * HID1 has only read-only information - nothing to set.
- */
-#define CONFIG_SYS_HID0_INIT (HID0_ICE|HID0_DCE|HID0_ICFI|HID0_DCI|\
- HID0_IFEM|HID0_ABE)
-#define CONFIG_SYS_HID0_FINAL (HID0_IFEM|HID0_ABE)
-#define CONFIG_SYS_HID2 0
-
-/*-----------------------------------------------------------------------
- * RMR - Reset Mode Register 5-5
- *-----------------------------------------------------------------------
- * turn on Checkstop Reset Enable
- */
-#define CONFIG_SYS_RMR RMR_CSRE
-
-/*-----------------------------------------------------------------------
- * BCR - Bus Configuration 4-25
- *-----------------------------------------------------------------------
- */
-#define CONFIG_SYS_BCR 0xA01C0000
-
-/*-----------------------------------------------------------------------
- * SIUMCR - SIU Module Configuration 4-31
- *-----------------------------------------------------------------------
- */
-#define CONFIG_SYS_SIUMCR 0X4205C000
-
-/*-----------------------------------------------------------------------
- * SYPCR - System Protection Control 4-35
- * SYPCR can only be written once after reset!
- *-----------------------------------------------------------------------
- * Watchdog & Bus Monitor Timer max, 60x Bus Monitor enable
- */
-#if defined (CONFIG_WATCHDOG)
-#define CONFIG_SYS_SYPCR (SYPCR_SWTC|SYPCR_BMT|SYPCR_PBME|SYPCR_LBME|\
- SYPCR_SWRI|SYPCR_SWP|SYPCR_SWE)
-#else
-#define CONFIG_SYS_SYPCR (SYPCR_SWTC|SYPCR_BMT|SYPCR_PBME|SYPCR_LBME|\
- SYPCR_SWRI|SYPCR_SWP)
-#endif /* CONFIG_WATCHDOG */
-
-/*-----------------------------------------------------------------------
- * TMCNTSC - Time Counter Status and Control 4-40
- * Clear once per Second and Alarm Interrupt Status, Set 32KHz timersclk,
- * and enable Time Counter
- *-----------------------------------------------------------------------
- */
-#define CONFIG_SYS_TMCNTSC (TMCNTSC_SEC|TMCNTSC_ALR|TMCNTSC_TCF|TMCNTSC_TCE)
-
-/*-----------------------------------------------------------------------
- * PISCR - Periodic Interrupt Status and Control 4-42
- *-----------------------------------------------------------------------
- * Clear Periodic Interrupt Status, Set 32KHz timersclk, and enable
- * Periodic timer
- */
-#define CONFIG_SYS_PISCR (PISCR_PS|PISCR_PTF|PISCR_PTE)
-
-/*-----------------------------------------------------------------------
- * SCCR - System Clock Control 9-8
- *-----------------------------------------------------------------------
- * Ensure DFBRG is Divide by 16
- */
-#define CONFIG_SYS_SCCR 0
-
-/*-----------------------------------------------------------------------
- * RCCR - RISC Controller Configuration 13-7
- *-----------------------------------------------------------------------
- */
-#define CONFIG_SYS_RCCR 0
-
-/*-----------------------------------------------------------------------
- * Init Memory Controller:
- *
- * Bank Bus Machine PortSz Device
- * ---- --- ------- ------ ------
- * 0 60x GPCM 64 bit FLASH
- * 1 60x SDRAM 64 bit SDRAM
- */
-
-#define CONFIG_SYS_BR0_PRELIM ((CONFIG_SYS_FLASH_BASE & BRx_BA_MSK) | 0x0801)
-#define CONFIG_SYS_OR0_PRELIM 0xFF800882
-#define CONFIG_SYS_BR1_PRELIM ((CONFIG_SYS_SDRAM_BASE & BRx_BA_MSK) | 0x0041)
-#define CONFIG_SYS_OR1_PRELIM 0xF8002CD0
-
-#define CONFIG_SYS_PSDMR 0x404A241A
-#define CONFIG_SYS_MPTPR 0x00007400
-#define CONFIG_SYS_PSRT 0x00000007
-
-#endif /* __CONFIG_H */
--
1.9.1
More information about the U-Boot
mailing list