[U-Boot] [PATCH v1 5/6] mmc: kona: Add Kona mmc driver

Darwin Rambo drambo at broadcom.com
Tue Feb 4 17:22:00 CET 2014



On 14-02-03 05:12 PM, Jaehoon Chung wrote:
> On 02/04/2014 06:03 AM, Darwin Rambo wrote:
>> Add support for the Kona SDHCI found on Broadcom mobile SoCs.
>>
>> Signed-off-by: Darwin Rambo <drambo at broadcom.com>
>> Reviewed-by: Steve Rae <srae at broadcom.com>
>> Reviewed-by: Tim Kryger <tkryger at linaro.org>
>> ---
>>  drivers/mmc/Makefile     |    1 +
>>  drivers/mmc/kona_sdhci.c |  125 ++++++++++++++++++++++++++++++++++++++++++++++
>>  2 files changed, 126 insertions(+)
>>  create mode 100644 drivers/mmc/kona_sdhci.c
>>
>> diff --git a/drivers/mmc/Makefile b/drivers/mmc/Makefile
>> index e793ed9..931922b 100644
>> --- a/drivers/mmc/Makefile
>> +++ b/drivers/mmc/Makefile
>> @@ -21,6 +21,7 @@ obj-$(CONFIG_OMAP_HSMMC) += omap_hsmmc.o
>>  obj-$(CONFIG_PXA_MMC_GENERIC) += pxa_mmc_gen.o
>>  obj-$(CONFIG_SDHCI) += sdhci.o
>>  obj-$(CONFIG_BCM2835_SDHCI) += bcm2835_sdhci.o
>> +obj-$(CONFIG_KONA_SDHCI) += kona_sdhci.o
>>  obj-$(CONFIG_S5P_SDHCI) += s5p_sdhci.o
>>  obj-$(CONFIG_SH_MMCIF) += sh_mmcif.o
>>  obj-$(CONFIG_SPEAR_SDHCI) += spear_sdhci.o
>> diff --git a/drivers/mmc/kona_sdhci.c b/drivers/mmc/kona_sdhci.c
>> new file mode 100644
>> index 0000000..69e6f17
>> --- /dev/null
>> +++ b/drivers/mmc/kona_sdhci.c
>> @@ -0,0 +1,125 @@
>> +/*
>> + * Copyright 2013 Broadcom Corporation.  All rights reserved.
>> + *
>> + * SPDX-License-Identifier:      GPL-2.0+
>> + */
>> +
>> +#include <common.h>
>> +#include <malloc.h>
>> +#include <sdhci.h>
>> +#include <asm/errno.h>
>> +#include <asm/kona-common/clk.h>
>> +
>> +#define SDHCI_CORECTRL_OFFSET		0x00008000
>> +#define SDHCI_CORECTRL_EN		0x01
>> +#define SDHCI_CORECTRL_RESET		0x02
>> +
>> +#define SDHCI_CORESTAT_OFFSET		0x00008004
>> +#define SDHCI_CORESTAT_CD_SW		0x01
>> +
>> +#define SDHCI_COREIMR_OFFSET		0x00008008
>> +#define SDHCI_COREIMR_IP		0x01
>> +
>> +static int init_mmc_core(struct sdhci_host *host)
> 
> I think that function name is used to "_kona_".
> This function isn't general mmc function, right?

Correct. I should rename it to init_kona_mmc_core(). Thanks.

> 
> Best Regards,
> Jaehoon Chung
> 
>> +{
>> +	unsigned int mask;
>> +	unsigned int timeout;
>> +
>> +	if (sdhci_readb(host, SDHCI_SOFTWARE_RESET) & SDHCI_RESET_ALL) {
>> +		printf("%s: sd host controller reset error\n", __func__);
>> +		return 1;
>> +	}
>> +
>> +	/* For kona a hardware reset before anything else. */
>> +	mask = sdhci_readl(host, SDHCI_CORECTRL_OFFSET) | SDHCI_CORECTRL_RESET;
>> +	sdhci_writel(host, mask, SDHCI_CORECTRL_OFFSET);
>> +
>> +	/* Wait max 100 ms */
>> +	timeout = 1000;
>> +	do {
>> +		if (timeout == 0) {
>> +			printf("%s: reset timeout error\n", __func__);
>> +			return 1;
>> +		}
>> +		timeout--;
>> +		udelay(100);
>> +	} while (0 ==
>> +		 (sdhci_readl(host, SDHCI_CORECTRL_OFFSET) &
>> +		  SDHCI_CORECTRL_RESET));
>> +
>> +	/* Clear the reset bit. */
>> +	mask = mask & ~SDHCI_CORECTRL_RESET;
>> +	sdhci_writel(host, mask, SDHCI_CORECTRL_OFFSET);
>> +	udelay(10);
>> +
>> +	/* Enable AHB clock */
>> +	mask = sdhci_readl(host, SDHCI_CORECTRL_OFFSET);
>> +	sdhci_writel(host, mask | SDHCI_CORECTRL_EN, SDHCI_CORECTRL_OFFSET);
>> +
>> +	/* Enable interrupts */
>> +	sdhci_writel(host, SDHCI_COREIMR_IP, SDHCI_COREIMR_OFFSET);
>> +
>> +	/* Make sure Card is detected in controller */
>> +	mask = sdhci_readl(host, SDHCI_CORESTAT_OFFSET);
>> +	sdhci_writel(host, mask | SDHCI_CORESTAT_CD_SW, SDHCI_CORESTAT_OFFSET);

BTW I think that this is a good spot to test and wait for CARD_PRESENT
with timeout. I should add it here. This avoids timing issues if the
core code tries to power up the card before it is recognized. Thanks.

>> +
>> +	return 0;
>> +}
>> +
>> +int kona_sdhci_init(int dev_index, u32 min_clk, u32 quirks)
>> +{
>> +	int ret = 0;
>> +	u32 max_clk;
>> +	void *reg_base;
>> +	struct sdhci_host *host = NULL;
>> +
>> +	host = (struct sdhci_host *)malloc(sizeof(struct sdhci_host));
>> +	if (!host) {
>> +		printf("%s: sdhci host malloc fail!\n", __func__);
>> +		return -ENOMEM;
>> +	}
>> +	switch (dev_index) {
>> +	case 0:
>> +		reg_base = (void *)CONFIG_SYS_SDIO_BASE0;
>> +		ret = clk_sdio_enable(reg_base, CONFIG_SYS_SDIO0_MAX_CLK,
>> +					&max_clk);
>> +		break;
>> +	case 1:
>> +		reg_base = (void *)CONFIG_SYS_SDIO_BASE1;
>> +		ret = clk_sdio_enable(reg_base, CONFIG_SYS_SDIO1_MAX_CLK,
>> +					&max_clk);
>> +		break;
>> +	case 2:
>> +		reg_base = (void *)CONFIG_SYS_SDIO_BASE2;
>> +		ret = clk_sdio_enable(reg_base, CONFIG_SYS_SDIO2_MAX_CLK,
>> +					&max_clk);
>> +		break;
>> +	case 3:
>> +		reg_base = (void *)CONFIG_SYS_SDIO_BASE3;
>> +		ret = clk_sdio_enable(reg_base, CONFIG_SYS_SDIO3_MAX_CLK,
>> +					&max_clk);
>> +		break;
>> +	default:
>> +		printf("%s: sdio dev index %d not supported\n",
>> +		       __func__, dev_index);
>> +		ret = -EINVAL;
>> +	}
>> +	if (ret)
>> +		return ret;
>> +
>> +	host->name = "kona-sdhci";
>> +	host->ioaddr = reg_base;
>> +	host->quirks = quirks;
>> +	host->host_caps = MMC_MODE_HC;
>> +
>> +	if (init_mmc_core(host))
>> +		return -EINVAL;
>> +
>> +	if (quirks & SDHCI_QUIRK_REG32_RW)
>> +		host->version = sdhci_readl(host, SDHCI_HOST_VERSION - 2) >> 16;
>> +	else
>> +		host->version = sdhci_readw(host, SDHCI_HOST_VERSION);
>> +
>> +	add_sdhci(host, max_clk, min_clk);
>> +	return ret;
>> +}
>>
> 


More information about the U-Boot mailing list