[U-Boot] [PATCH V2 09/12] board:origen: Enable device tree on Origen
Piotr Wilczek
p.wilczek at samsung.com
Thu Feb 13 15:10:27 CET 2014
This patch enables to run Origen board on device tree.
Uart, DRAM and MMC init functions are removed as their
generic replacements form the common board file are used.
The config file is modified to contain only board specific options.
Signed-off-by: Piotr Wilczek <p.wilczek at samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park at samsung.com>
Cc: Chander Kashyap <k.chander at samsung.com>
Cc: Minkyu Kang <mk7.kang at samsung.com>
---
Changes for v2:
- no changes;
board/samsung/dts/exynos4210-origen.dts | 45 ++++++++++++
board/samsung/origen/origen.c | 112 +++--------------------------
include/configs/origen.h | 117 +++++++++++--------------------
3 files changed, 94 insertions(+), 180 deletions(-)
create mode 100644 board/samsung/dts/exynos4210-origen.dts
diff --git a/board/samsung/dts/exynos4210-origen.dts b/board/samsung/dts/exynos4210-origen.dts
new file mode 100644
index 0000000..5c9d2ae
--- /dev/null
+++ b/board/samsung/dts/exynos4210-origen.dts
@@ -0,0 +1,45 @@
+/*
+ * Samsung's Exynos4210 based Origen board device tree source
+ *
+ * Copyright (c) 2014 Samsung Electronics Co., Ltd.
+ * http://www.samsung.com
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+/dts-v1/;
+/include/ "skeleton.dtsi"
+/include/ "exynos4.dtsi"
+
+/ {
+ model = "Insignal Origen evaluation board based on Exynos4210";
+ compatible = "insignal,origen", "samsung,exynos4210";
+
+ chosen {
+ bootargs ="";
+ };
+
+ aliases {
+ serial0 = "/serial at 13800000";
+ console = "/serial at 13820000";
+ mmc2 = "sdhci at 12530000";
+ };
+
+ sdhci at 12510000 {
+ status = "disabled";
+ };
+
+ sdhci at 12520000 {
+ status = "disabled";
+ };
+
+ sdhci at 12530000 {
+ samsung,bus-width = <4>;
+ samsung,timing = <1 2 3>;
+ cd-gpios = <&gpio 0x2008002 0>;
+ };
+
+ sdhci at 12540000 {
+ status = "disabled";
+ };
+};
\ No newline at end of file
diff --git a/board/samsung/origen/origen.c b/board/samsung/origen/origen.c
index 15f77ca..d502f02 100644
--- a/board/samsung/origen/origen.c
+++ b/board/samsung/origen/origen.c
@@ -11,129 +11,35 @@
#include <asm/arch/mmc.h>
#include <asm/arch/periph.h>
#include <asm/arch/pinmux.h>
+#include <usb.h>
DECLARE_GLOBAL_DATA_PTR;
-struct exynos4_gpio_part1 *gpio1;
-struct exynos4_gpio_part2 *gpio2;
-int board_init(void)
+u32 get_board_rev(void)
{
- gpio1 = (struct exynos4_gpio_part1 *) EXYNOS4_GPIO_PART1_BASE;
- gpio2 = (struct exynos4_gpio_part2 *) EXYNOS4_GPIO_PART2_BASE;
-
- gd->bd->bi_boot_params = (PHYS_SDRAM_1 + 0x100UL);
return 0;
}
-static int board_uart_init(void)
+int exynos_init(void)
{
- int err;
-
- err = exynos_pinmux_config(PERIPH_ID_UART0, PINMUX_FLAG_NONE);
- if (err) {
- debug("UART0 not configured\n");
- return err;
- }
-
- err = exynos_pinmux_config(PERIPH_ID_UART1, PINMUX_FLAG_NONE);
- if (err) {
- debug("UART1 not configured\n");
- return err;
- }
-
- err = exynos_pinmux_config(PERIPH_ID_UART2, PINMUX_FLAG_NONE);
- if (err) {
- debug("UART2 not configured\n");
- return err;
- }
-
- err = exynos_pinmux_config(PERIPH_ID_UART3, PINMUX_FLAG_NONE);
- if (err) {
- debug("UART3 not configured\n");
- return err;
- }
-
return 0;
}
-#ifdef CONFIG_BOARD_EARLY_INIT_F
-int board_early_init_f(void)
-{
- int err;
- err = board_uart_init();
- if (err) {
- debug("UART init failed\n");
- return err;
- }
- return err;
-}
-#endif
-
-int dram_init(void)
+int board_usb_init(int index, enum usb_init_type init)
{
- gd->ram_size = get_ram_size((long *)PHYS_SDRAM_1, PHYS_SDRAM_1_SIZE)
- + get_ram_size((long *)PHYS_SDRAM_2, PHYS_SDRAM_2_SIZE)
- + get_ram_size((long *)PHYS_SDRAM_3, PHYS_SDRAM_3_SIZE)
- + get_ram_size((long *)PHYS_SDRAM_4, PHYS_SDRAM_4_SIZE);
-
return 0;
}
-void dram_init_banksize(void)
-{
- gd->bd->bi_dram[0].start = PHYS_SDRAM_1;
- gd->bd->bi_dram[0].size = get_ram_size((long *)PHYS_SDRAM_1, \
- PHYS_SDRAM_1_SIZE);
- gd->bd->bi_dram[1].start = PHYS_SDRAM_2;
- gd->bd->bi_dram[1].size = get_ram_size((long *)PHYS_SDRAM_2, \
- PHYS_SDRAM_2_SIZE);
- gd->bd->bi_dram[2].start = PHYS_SDRAM_3;
- gd->bd->bi_dram[2].size = get_ram_size((long *)PHYS_SDRAM_3, \
- PHYS_SDRAM_3_SIZE);
- gd->bd->bi_dram[3].start = PHYS_SDRAM_4;
- gd->bd->bi_dram[3].size = get_ram_size((long *)PHYS_SDRAM_4, \
- PHYS_SDRAM_4_SIZE);
-}
-
-#ifdef CONFIG_DISPLAY_BOARDINFO
-int checkboard(void)
+#ifdef CONFIG_USB_CABLE_CHECK
+int usb_cable_connected(void)
{
- printf("\nBoard: ORIGEN\n");
return 0;
}
#endif
-#ifdef CONFIG_GENERIC_MMC
-int board_mmc_init(bd_t *bis)
+#ifdef CONFIG_BOARD_EARLY_INIT_F
+int exynos_early_init_f(void)
{
- int i, err;
-
- /*
- * MMC2 SD card GPIO:
- *
- * GPK2[0] SD_2_CLK(2)
- * GPK2[1] SD_2_CMD(2)
- * GPK2[2] SD_2_CDn
- * GPK2[3:6] SD_2_DATA[0:3](2)
- */
- for (i = 0; i < 7; i++) {
- /* GPK2[0:6] special function 2 */
- s5p_gpio_cfg_pin(&gpio2->k2, i, GPIO_FUNC(0x2));
-
- /* GPK2[0:6] drv 4x */
- s5p_gpio_set_drv(&gpio2->k2, i, GPIO_DRV_4X);
-
- /* GPK2[0:1] pull disable */
- if (i == 0 || i == 1) {
- s5p_gpio_set_pull(&gpio2->k2, i, GPIO_PULL_NONE);
- continue;
- }
-
- /* GPK2[2:6] pull up */
- s5p_gpio_set_pull(&gpio2->k2, i, GPIO_PULL_UP);
- }
-
- err = s5p_mmc_init(2, 4);
- return err;
+ return 0;
}
#endif
diff --git a/include/configs/origen.h b/include/configs/origen.h
index f46b833..2c973cb 100644
--- a/include/configs/origen.h
+++ b/include/configs/origen.h
@@ -6,115 +6,79 @@
* SPDX-License-Identifier: GPL-2.0+
*/
-#ifndef __CONFIG_H
-#define __CONFIG_H
+#ifndef __CONFIG_ORIGEN_H
+#define __CONFIG_ORIGEN_H
+
+#include <configs/exynos4-dt.h>
+
+#define CONFIG_SYS_PROMPT "ORIGEN # "
+
+#undef CONFIG_DEFAULT_DEVICE_TREE
+#define CONFIG_DEFAULT_DEVICE_TREE exynos4210-origen
/* High Level Configuration Options */
-#define CONFIG_SAMSUNG 1 /* SAMSUNG core */
-#define CONFIG_S5P 1 /* S5P Family */
#define CONFIG_EXYNOS4210 1 /* which is a EXYNOS4210 SoC */
#define CONFIG_ORIGEN 1 /* working with ORIGEN*/
-#include <asm/arch/cpu.h> /* get chip and board defs */
-
-#define CONFIG_ARCH_CPU_INIT
-#define CONFIG_DISPLAY_CPUINFO
-#define CONFIG_DISPLAY_BOARDINFO
-#define CONFIG_BOARD_EARLY_INIT_F
-
#define CONFIG_SYS_DCACHE_OFF 1
+/* ORIGEN has 4 bank of DRAM */
+#define CONFIG_NR_DRAM_BANKS 4
#define CONFIG_SYS_SDRAM_BASE 0x40000000
-#define CONFIG_SYS_TEXT_BASE 0x43E00000
+#define PHYS_SDRAM_1 CONFIG_SYS_SDRAM_BASE
+#define SDRAM_BANK_SIZE (256 << 20) /* 256 MB */
-/* input clock of PLL: ORIGEN has 24MHz input clock */
-#define CONFIG_SYS_CLK_FREQ 24000000
+/* memtest works on */
+#define CONFIG_SYS_MEMTEST_START CONFIG_SYS_SDRAM_BASE
+#define CONFIG_SYS_MEMTEST_END (CONFIG_SYS_SDRAM_BASE + 0x6000000)
+#define CONFIG_SYS_LOAD_ADDR (CONFIG_SYS_SDRAM_BASE + 0x3E00000)
-#define CONFIG_SETUP_MEMORY_TAGS
-#define CONFIG_CMDLINE_TAG
-#define CONFIG_INITRD_TAG
-#define CONFIG_CMDLINE_EDITING
+#define CONFIG_SYS_TEXT_BASE 0x43E00000
#define CONFIG_MACH_TYPE MACH_TYPE_ORIGEN
-/* Power Down Modes */
-#define S5P_CHECK_SLEEP 0x00000BAD
-#define S5P_CHECK_DIDLE 0xBAD00000
-#define S5P_CHECK_LPA 0xABAD0000
-
/* Size of malloc() pool */
-#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + (1 << 20))
+#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + (80 * SZ_1M))
/* select serial console configuration */
-#define CONFIG_SERIAL2 1 /* use SERIAL 2 */
+#define CONFIG_SERIAL2
#define CONFIG_BAUDRATE 115200
-#define EXYNOS4_DEFAULT_UART_OFFSET 0x020000
-#define CONFIG_SKIP_LOWLEVEL_INIT
+/* Console configuration */
+#define CONFIG_SYS_CONSOLE_INFO_QUIET
+#define CONFIG_SYS_CONSOLE_IS_IN_ENV
+
+#define CONFIG_BOOTARGS "Please use defined boot"
+#define CONFIG_BOOTCOMMAND "run mmcboot"
+#define CONFIG_DEFAULT_CONSOLE "console=ttySAC1,115200n8\0"
-/* SD/MMC configuration */
-#define CONFIG_GENERIC_MMC
-#define CONFIG_MMC
-#define CONFIG_SDHCI
-#define CONFIG_S5P_SDHCI
+#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_LOAD_ADDR \
+ - GENERATED_GBL_DATA_SIZE)
-/* PWM */
-#define CONFIG_PWM 1
+#define CONFIG_SYS_MEM_TOP_HIDE (1 << 20) /* ram console */
-/* allow to overwrite serial and ethaddr */
-#define CONFIG_ENV_OVERWRITE
+#define CONFIG_SYS_MONITOR_BASE 0x00000000
-/* Command definition*/
-#include <config_cmd_default.h>
+/* Power Down Modes */
+#define S5P_CHECK_SLEEP 0x00000BAD
+#define S5P_CHECK_DIDLE 0xBAD00000
+#define S5P_CHECK_LPA 0xABAD0000
#undef CONFIG_CMD_PING
#define CONFIG_CMD_ELF
#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_MMC
-#define CONFIG_CMD_FAT
#undef CONFIG_CMD_NET
#undef CONFIG_CMD_NFS
-#define CONFIG_BOOTDELAY 3
-#define CONFIG_ZERO_BOOTDELAY_CHECK
/* MMC SPL */
#define CONFIG_SPL
#define COPY_BL2_FNPTR_ADDR 0x02020030
#define CONFIG_SPL_TEXT_BASE 0x02021410
+#undef CONFIG_BOOTCOMMAND
#define CONFIG_BOOTCOMMAND "fatload mmc 0 40007000 uImage; bootm 40007000"
-/* Miscellaneous configurable options */
-#define CONFIG_SYS_LONGHELP /* undef to save memory */
-#define CONFIG_SYS_HUSH_PARSER /* use "hush" command parser */
-#define CONFIG_SYS_PROMPT "ORIGEN # "
-#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size*/
-#define CONFIG_SYS_PBSIZE 384 /* Print Buffer Size */
-#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
-#define CONFIG_DEFAULT_CONSOLE "console=ttySAC2,115200n8\0"
-/* Boot Argument Buffer Size */
-#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
-/* memtest works on */
-#define CONFIG_SYS_MEMTEST_START CONFIG_SYS_SDRAM_BASE
-#define CONFIG_SYS_MEMTEST_END (CONFIG_SYS_SDRAM_BASE + 0x6000000)
-#define CONFIG_SYS_LOAD_ADDR (CONFIG_SYS_SDRAM_BASE + 0x3E00000)
-
-/* ORIGEN has 4 bank of DRAM */
-#define CONFIG_NR_DRAM_BANKS 4
-#define SDRAM_BANK_SIZE (256UL << 20UL) /* 256 MB */
-#define PHYS_SDRAM_1 CONFIG_SYS_SDRAM_BASE
-#define PHYS_SDRAM_1_SIZE SDRAM_BANK_SIZE
-#define PHYS_SDRAM_2 (CONFIG_SYS_SDRAM_BASE + SDRAM_BANK_SIZE)
-#define PHYS_SDRAM_2_SIZE SDRAM_BANK_SIZE
-#define PHYS_SDRAM_3 (CONFIG_SYS_SDRAM_BASE + (2 * SDRAM_BANK_SIZE))
-#define PHYS_SDRAM_3_SIZE SDRAM_BANK_SIZE
-#define PHYS_SDRAM_4 (CONFIG_SYS_SDRAM_BASE + (3 * SDRAM_BANK_SIZE))
-#define PHYS_SDRAM_4_SIZE SDRAM_BANK_SIZE
-
-/* FLASH and environment organization */
-#define CONFIG_SYS_NO_FLASH 1
-#undef CONFIG_CMD_IMLS
#define CONFIG_IDENT_STRING " for ORIGEN"
#define CONFIG_CLK_1000_400_200
@@ -122,17 +86,17 @@
/* MIU (Memory Interleaving Unit) */
#define CONFIG_MIU_2BIT_21_7_INTERLEAVED
-#define CONFIG_ENV_IS_IN_MMC 1
-#define CONFIG_SYS_MMC_ENV_DEV 0
+#undef CONFIG_ENV_SIZE
#define CONFIG_ENV_SIZE (16 << 10) /* 16 KB */
#define RESERVE_BLOCK_SIZE (512)
#define BL1_SIZE (16 << 10) /*16 K reserved for BL1*/
+#undef CONFIG_ENV_OFFSET
#define CONFIG_ENV_OFFSET (RESERVE_BLOCK_SIZE + BL1_SIZE)
-#define CONFIG_DOS_PARTITION 1
#define CONFIG_SPL_LDSCRIPT "board/samsung/common/exynos-uboot-spl.lds"
#define CONFIG_SPL_MAX_FOOTPRINT (14 * 1024)
+#undef CONFIG_SYS_INIT_SP_ADDR
#define CONFIG_SYS_INIT_SP_ADDR 0x02040000
/* U-boot copy size from boot Media to DRAM.*/
@@ -140,7 +104,6 @@
#define BL2_START_OFFSET ((CONFIG_ENV_OFFSET + CONFIG_ENV_SIZE)/512)
#define BL2_SIZE_BLOC_COUNT (COPY_BL2_SIZE/512)
-/* Enable devicetree support */
-#define CONFIG_OF_LIBFDT
+#undef CONFIG_CMD_I2C
#endif /* __CONFIG_H */
--
1.7.9.5
More information about the U-Boot
mailing list